Author Topic: The Master Of Magnetics "Steven Mark" (Read 1242944 times)

HMM · « **Reply #750 on:** September 26, 2006, 07:59:00 AM »

Hey,
Has anybody tried using segments of wire all in parallel as the collector coil. I remember a post saying it would allow more current to be taken.

Mike

raburgeson · « **Reply #751 on:** September 26, 2006, 10:44:53 AM »

People say they want totally independent control of distribution of the coil rotation. It's simple take 2 12 volt motors mount them in a box (Plastic probably) run them independently with 2 cheap train transformers. Put a plastic plate with 2 holes to fit past the armitures. Place 2 large plastic washers over the armitures that have a large enough diameter to hold 4 contacts bent to make contact with the distributor disks. Make 2 metal disks drill in the center to fit the armature with nylon bushings availible in your area. Paint epoxy on motor side, might have made a lock screw on this side,leave a 90 degree V point end towards the center hole. Make brushes from brass shim stock, it's springy. Cut the back so it is a male spade. Input power goes to the unpainted side. The brush you make for it can be mounted anywhere, make it too long you will need fairly thick stock. Anytime after the plastic washer is set in place you can drill a small hole just outside the edge, screw in a flat head screw for a set screw. Then you can loosen it and set the timing. Wire 1 motor clockwise the other counter-clockwise. If you want to input several signals at once make a spade harness, crimp several wires onto a female spade and put males on the other ends. Turn the whole assembly upside down and cut some thin strips of plastic and an old soldering iron and plastic weld the box in place. That way you wont be forever rebending your contacts.
I just found 2 old sewing machine motors but am still looking for lower draw dc, I'll get them by the weekend.

mrd10 · « **Reply #752 on:** September 26, 2006, 11:21:07 AM »

Hi All,

I have been reading all, and have been thinking about this alot, and this is what I will start off with after I finish up torbays magnet motor/gen
which is in the magnets section in this forum.

The picture I pasted, I believe holds some of or all of the key, and is what i will be starting off with, it was one of the pics on this forum under the stevens files:- http://www.overunity.com/stevenmark/ I know someone mentioned this already, but it hit me on how he has made these devices

From the videos look at the solid versions, looks very similar to the naked one Ive attached, look where the output wires are, I believe he is feeding two different frequencies into two seperate sections of coil but on one of the rings, these coils are as shown in the pic, and the magnet on the back has something to do with it as well. I'm new to transformers as such, but i've been trying to learn by reading and understanding, it's like i can't stop thinking about it, as i play it in my mind over and over

Just thought I'd give everyone some direction of what they should try first.

cheers,

Mrd

raburgeson · « **Reply #753 on:** September 26, 2006, 06:34:05 PM »

Has anyone rotated the fields fast yet. Did you get a light head throb at a very slow speed? would litz wire be better for the inside coil?

raburgeson · « **Reply #754 on:** September 26, 2006, 06:51:15 PM »

So far I'm just puting in 5 volt dc and trying to see if I get noise generation. Steven said to experiment to learn what the interaction of the coils do. I'm not as far advanced as most in here, I'm just looking and trying to learn. I haven't even read all the posts yet so I'm keeping this low voltage for the moment. I could add a signal from a noise generator, that might be interesting, or maybe hook up sterrio output to it to find out what's better rock or country. Actually I would like to see how the fields interact first.

Coiling does suck doesn't it and had super glue screw up my insulation and there by not stick. Ended up using duco cement and a quick tie gun to hold things in place over night, I could use some good ideas on wrapping also.

Dingus Mungus · « **Reply #755 on:** September 26, 2006, 07:33:17 PM »

Quote from: -[marco]- on September 26, 2006, 06:27:55 PM

Quote from: ctglabs on September 26, 2006, 06:03:47 PM
Marco,

Please watch the video, are you sure it is the right video?!
Hmm, perhaps this is what is meant by the large wires for the collectors?
Can you post the right video for us?

Dave.

hi dave ,

it is the right video.
the amusement park ride is lika big capacitor
they take it up verry slowly....then when its up the release all energy abruptly, then stop the ride abrubtly as its down...it kicks back up and so on.
so for those people are the elektrons/wires and one has more mass so it makes visible diffrence.

its kinda symbolic

ROFL!!!

Thats one of the best anecdotal examples ever... Truely though I believe you're correct in your observations, while each coil is in a state of discharge it produces an extra kick from a harmonic resonance that extra energy is fed to another coil to help energize that coil to the point where it can then discharge and achieve the same effects. So it would be like many roller costers powering each other, but it still made perfect sense to me. LOL!

raburgeson · « **Reply #756 on:** September 26, 2006, 07:44:53 PM »

Thanks for the warning Dave I'm once bitten by 660 and twice shy. I think my large coil sucks and I shoud make another one.

raburgeson · « **Reply #757 on:** September 27, 2006, 12:39:09 AM »

I hope Steven is still talking to us. I know the group is hell bent towards reverse engineering because of the way the controling companies hide advances. But the group is in a mode that is not called for in this case. Steven Mark is not the establishment, he is a man seening the work that would help the world being shelved. He has offered his tutoring in the right direction as much as the law will allow. Please people he has spent 15 years developing and I am sure he will share the knowledge gained, Steven and the company he worked for hold patents. They did not borrow from other patents. They found a way to collect ambient magnetic force, this causes gain, gain=overunity or you can better say he is collecting energy that is not on a meter. In an early post (not an exact quote) Steve said the circuit will draw in magnetic flux like an antenna draws in a signal. Put aside you're aggression you got from trying to learn how other circuits work from sources that hid information. I looked at the propaganda this man has endured and he deserves our attention, calm down and become students.

Alright, lets say you manage to reverse engineer this circuit and you don't understand why it works. Lets also say you build a flying machine, this machine works fine but when you try to past the ionosphere it no longer works. Suddenly you are in the suns magnetic field and storms and what do you know...squat. Learn about this circuit from the inventer, he's probably putting himself in harms way making himself available to you.

gn0stik · « **Reply #758 on:** September 27, 2006, 07:34:40 AM »

Quote from: raburgeson on September 27, 2006, 12:39:09 AM

I hope Steven is still talking to us. I know the group is hell bent towards reverse engineering because of the way the controling companies hide advances. But the group is in a mode that is not called for in this case. Steven Mark is not the establishment, he is a man seening the work that would help the world being shelved. He has offered his tutoring in the right direction as much as the law will allow. Please people he has spent 15 years developing and I am sure he will share the knowledge gained, Steven and the company he worked for hold patents. They did not borrow from other patents. They found a way to collect ambient magnetic force, this causes gain, gain=overunity or you can better say he is collecting energy that is not on a meter. In an early post (not an exact quote) Steve said the circuit will draw in magnetic flux like an antenna draws in a signal. Put aside you're aggression you got from trying to learn how other circuits work from sources that hid information. I looked at the propaganda this man has endured and he deserves our attention, calm down and become students.

Alright, lets say you manage to reverse engineer this circuit and you don't understand why it works. Lets also say you build a flying machine, this machine works fine but when you try to past the ionosphere it no longer works. Suddenly you are in the suns magnetic field and storms and what do you know...squat. Learn about this circuit from the inventer, he's probably putting himself in harms way making himself available to you.

Nice sentiments, but who..... uhhh.... are you talking to... exactly?

dean_mcgowan · « **Reply #759 on:** September 27, 2006, 08:33:58 AM »

500 bucks .. would be a pretty expensive toy to pull apart to see how it works

dean_mcgowan · « **Reply #760 on:** September 27, 2006, 08:35:44 AM »

does it spin in the correct direction in the southern hemisphere :|

dean_mcgowan · « **Reply #761 on:** September 27, 2006, 10:57:21 AM »

it took engineers 6 years to attach a compass needle to a a piss week motor and power it with a solar panel

pure genius.. and what were they doing in their spare time .. smoking bongs

supersam · « **Reply #762 on:** September 27, 2006, 04:43:22 PM »

back them off 18 degrees and you'll have the thing hitting on 5 cilinders instead of four it has got to help! 72 degrees X 5= 360 degrees. you have to start at least thinking about the golden numbers.

lol
sam

Dingus Mungus · « **Reply #763 on:** September 27, 2006, 05:21:40 PM »

Quote from: tao on September 27, 2006, 08:17:59 AM

The globe encloses a photoreceptor that gathers room light to power an internal drive

The machine uses photocell photon energy convertion to power a small asymetricly weighted dc motor. The unidirectional 'wobble' allows the smooth globe to rotate within the smooth base due to a lack of friction and the added energy from the ambient light. The globe would turn which ever direction the motor is spinning, meaning if the globe spun clockwise right side up, it would then spin counter clockwise if the globe was flipped upside down. This device in no way havests any power from the ionisphere or earth magnetic field...

Just trying to help...

giantkiller · « **Reply #764 on:** September 27, 2006, 05:37:43 PM »

On my circuit, thanks CTGlabs, I have direction and speed seperate from the other drive channel. Each one is made up of 2 controllers with 4 lines for 4 coils. Each controller has direction and speed. On board? So if I speed one controller at 10 hz and the other at 50 hz ccw, the lissajous is 1:5. Magnetically the pattern is a crossover interference pattern of 5. Change the speed of either and you change performance.
Try this: http://www.ngsir.netfirms.com/englishhtm/Lissajous.htm or
http://www.mathcats.com/explore/lissajous/lissajous.html. On this on, press 'F' or 'S' and you see will the Mag field for the HAMEL disk! Anyone that read his publish will know that he experienced the frequency changes as his device reached unity, overunity and extreme power push against the base magneitc field of earth. No different than high power transmisions. But the big difference in doing it magentically I can control then interference harmonic. The HAMEL disk, when ramping up to runaway mode, went through distinct changes from screaming to glowing to huge power field generation and then it shot up into the sky. He never saw it again. Gee that sounds like Area 51 material.

Today, I go and get parts for the PHYZX engr. Magnetic field Lissajous controller. That is the name and consider it published. Feel free to devise.

Thank guys. You know I'll keep publishing what I do. And the steps taken so far in the last two weeks are very important. Each one could be considered a new direction for different results/products. The screaming ferrite bead? Sounds like Hamel disk again. I think repulsion is at hand.

Avacado!

News:

User Menu

Author Topic: The Master Of Magnetics "Steven Mark" (Read 1242944 times)

HMM

Re: The Master Of Magnetics "Steven Mark"

raburgeson

Re: The Master Of Magnetics "Steven Mark"

mrd10

Re: The Master Of Magnetics "Steven Mark"

raburgeson

Re: The Master Of Magnetics "Steven Mark"

raburgeson

Re: The Master Of Magnetics "Steven Mark"

Dingus Mungus

Re: The Master Of Magnetics "Steven Mark"

raburgeson

Re: The Master Of Magnetics "Steven Mark"

raburgeson

Re: The Master Of Magnetics "Steven Mark"

gn0stik

Re: The Master Of Magnetics "Steven Mark"

dean_mcgowan

Re: The Master Of Magnetics "Steven Mark"

dean_mcgowan

Re: The Master Of Magnetics "Steven Mark"

dean_mcgowan

Re: The Master Of Magnetics "Steven Mark"

supersam

Re: The Master Of Magnetics "Steven Mark"

Dingus Mungus

Re: The Master Of Magnetics "Steven Mark"

giantkiller

Re: The Master Of Magnetics "Steven Mark"