hi carl  ,
until now i measured 2 possibilaties.
the most outside wires and the wire from bottom 1 and top 3 coil.

in my next video you can see what happens when the output begins to feed the input.
marco.

Wow, just viewed the video, what is the voltage of the bulb you are lighting?

Looks like inductive pickup to the coils, how were they configured/connected?

Carl

Marco,

Have you tried to measure the voltage going to the bulb yet? If so what was it? IF not could you try to? maybe try a regular light bulb and see if it lights.

Carl

Dave,

I'm thinking he is acting as an antenna (transmitter) and the coil is picking up the signal (receiving antenna). I am thinking the center coil is providing the magnetic bias we are looking for. I am wondering if Marco adds a control coil and induces the signal there he might experience the same effect. I am thinking this is worth a try. What do you guys think?


Carl

Quote from: argona369 on October 13, 2006, 10:36:53 PM

Quote from: -[marco]- on October 13, 2006, 07:57:27 PM

Quote from: starcruiser on October 13, 2006, 07:38:04 PM

Quote from: -[marco]- on October 13, 2006, 07:03:20 PM

i have.
it looks like less with the wires looped.
it getting scary cause im measurin things that cant be.

Marco all 4 possibilities? with coils (top and bottom ones) both Clockwise, both counter clockwise (in relation to the center coils winding) as well as fliping the connections on the top and bottom so the top coils outside winding is connecting to the bottom coils inside and visa versa to see if the output varies substantially.

Carl

hi carl  ,
until now i measured 2 possibilaties.
the most outside wires and the wire from bottom 1 and top 3 coil.

in my next video you can see what happens when the output begins to feed the input.
marco.

Hi, amassing, truly amassing.
RE: part-3.wmv

Is this how its set up?

3 coils of iron wire (not parallel wound with copper)

All same direction wound. I.e. all clockwise (or counter-clockwise) looking downwards.

(a)Outside wire bottom to inside wire top.
(b)Inside wire bottom to outside wire top, 12 volt bulb in series in-between connection,
Or bulb connected between connections  a,b?

Middle coil fed ?juice? ac or dc? Voltage?

Mp3 players output center wire (hot) to finger. Sine wave? Frequency?

Other hand near coils pile


Cliff,

guys i said the bulb was for you to see how the coils react to my hand otherwise you would only hear the sound.
so the bulb is switched in with the juice wich is collector coil 2.
i did shortcut the outside two collectors cause then it reacted better.
in the beginning it reacted about ten centimeter now i got it to react as im standing a meter away from it.
its amazing and im still thinking about what sort of field it is.
as i grab the coils the frequency goes down but the output goes oup about 35 volt max.
then you can feel it resonating.
i did also quickly wrap a control coil around it as i put the jack on it then it goes to maximum output at once.the jack picks up the signal from the coil feeds it back into the transmitter and all starts over again.

marco.

This reminds me of the old days of antenna based TV reception, when you had to stand in certain places and move around the room to get the signal to come in right. This also happens with radio reception. The other day I went to the movies with a friend of mine and radio reception at his house was crappy, but when he started walking up to the car it started getting clearer.

So when you wrap the control wires around it @ 90 it pumps the reception up to full instantly. Interesting, do you still get any reaction with your hand/body moving closer or farther away? I would think not. So basically your body was the control. When it had no control, you held the input jack with your hand, and waved the other hand closer and farther away and that made the light go bright and dim. Now that you have a control around it. Do you hold one end of the control wire to produce the effect?

What will be interesting to see, is how the output raises with a proper control winding...

Is it the hot side or the cold side that you can light the light with? TEM/LMD on steroids anyone?

I'll edit it.

Hi Dave,

The last posts in this forum are really amazing.
My post is an answer to your question and it is not related to the last posts here.
My set up for a bifilar coil experiment was next:

Equipment:
Function Generator, Oscilloscope with 1mv/div max sensitivity. Digital multimeter with ability to measure 0.0001 volt. Power Source Signal ? a car audio amplifier 300W. Frequency range was between 1 KHz and 15 KHz.

Coil:
Winding was done with 4 wires at a time, single layer, high quality coil, ferrite rod. Let?s number the wires from either side as 1, 2, 3, and 4. Assuming it, numbers 1 and 4 are representing the input bifilar coil. Numbers 2 and 3 represent output coil. In other words, the input coil are 2 wires outside and the output coil are 2 wires in the middle. The number of turns is 50. The wire type is 20G. At the other end the coils (1 and 4, 2 and 3) were connected in order to form two bifilar coils, output coil is in the middle of each turn of the input coil.

Testing for symmetry:
This is important. If the quality of windings is not good, you will be getting an output signal as a result of the asymmetry and not as a result of the HOOPER-MONSTEIN effect. How to test it? I had another coil wound on the ferrite rod. I powered that coil for a short time with about 70W signal and checked the signal in both bifilar coils. It was zero. When testing it, you have to load the output coil with some resistor, otherwise, you will be testing ?antenna effect? instead of real asymmetry/noise. I don?t remember exactly, but my each bifilar coil was 0.26 Ohm. The output coil was connected to 10-Ohm resistor to avoid any ?antenna effect?.

Results:
The set up was tested with the input power between 0 and 50W. The max output power was somewhere in the middle. With low input, it is obvious, the output was low too. With max input, the output was also low, which can be explain as increased cancellation of the magnetic flux because of the close proximity between each turn (4 wires) in the bifilar coils. The load was tested with a resistor between 10 Ohm and 1K. There was no difference in the output signal or input power consumption. The max amplitude of the output was around 0.5 V and was just enough to light a led.

Unusual:
When the output signal was connected to LC in series, the resonance was occurring with a very high hysteresis. The point of resonance was occurring far (higher frequency) after where it was supposed to be. When the frequency was going down, a perfect resonance continued to exist until the frequency was reaching the point far below the point of resonance and then abruptly disappearing.

Let me know if something wasn?t explained clear.

Kames.

As a reminder:
There are over 100 dead scientists so far who had the ability to speak.
One of them was the promoter of free energy, Doctor Eugene Mallove
http://www.zpenergy.com/modules.php?name=News&file=article&sid=738

How much you want to bet Tom bearden will be next. Anyone who speaks up will be shut down. Look, we all know the story about who thinks they can save the day ends their days.

No disrespect, Mr. Bearden. But we all know the costs and the enemies. Anyone pusuing this adventure can look at themselves as enemies of the state.

This thread has existed so far because of the safety in numbers. There is no such thing as 'Conspiracy theory'.
I wish us all well in this endeveavor.

I hate to post like this, but there are those that constantly say 'It can't be done, cause it would have already been done.' And I for one am tired of it. There are things far greater than our understanding that we have yet to come upon.
Gutenberg:
How many centuries did it take to get printed material?
Lister:
Operation using Lister's carbolic spray invented in 1869
Although his methods initially met with indifference and hostility, doctors gradually began to support his antiseptic techniques.
In 1870 Lister's antiseptic methods were used, by Germany, during the Franco-Prussian war saving many Prussian soldier's lives. In Germany, by 1878, Robert Koch was demonstrating the usefulness of steam for sterilizing surgical instruments and dressings.

126k abortions everyday.
tens of thousands starve to death every day.http://www.theradicaltruth.com/Footnotes/ff-starve-fn.htm
And these things can be done?

We are still barbarians... We so speedily stand behind doubt and avarice and kill the dreams of visionaries so quickly.
I will not be condemned by the status quo. Sorry to defile this thread.

--giantkiller, hence the name.