Author Topic: Kapanadze Cousin - DALLY FREE ENERGY (Read 11881870 times)

Hoppy · « **Reply #1125 on:** April 29, 2013, 07:24:50 PM »

Quote from: Vortex1 on April 26, 2013, 04:17:16 PM

The most obvious is the long red twisted pair. It seems way too long for the job and may meander down over the edge of the table to a power supply or battery below. (kako chibridze video)

Regarding the akula video, my impression of the back of the chair does not appear to be a twin wire as it too carefully follows the contour curve of what we would expect to see. Besides there are no such wires shown on the top of the board or visible coming out of a hole in the board.

IMO the most likely way that the chibridze video could be faked, would have been to take a mains live feed up through a hole in the demo board into the centre of the air coil and connect this to one side of L4. The mains supply is then conveniently controlled by the switch, with the neutral side coming through the croc clip lead, which is called the earth lead in the demo. The red twisted pair is flicked out of the way in one clip and there is a view that shows the complete length of the twisted pair clear of the demo board edge.

With regards to the Aukula video, on further observation, I don't think there is a wire under the upper red arrow but there does appear to be twin cable sitting on top of the timber seat edging, following it in a curve around the chair under the lower arrow. If you look very carefully, the cable drops over the side of the chair. The other side of the cable probably drops down the back of the chair and is concealed from camera view by the top left hand corner of the back rest. I've attached the video clip again for easy access.

Edit: Video clip is Aukula self-runner, not Tungus as labelled.

NickZ · « **Reply #1126 on:** April 29, 2013, 07:57:38 PM »

Ok, so I was playing with my new Galaxy cell phone that I just got as a gift, and I just viewed this video from Eric (link below), about cell phones and cell phone towers, RF and such.
So, I look out my living room window, and this is what I see (pic below), less than 80 yards away from my living room window, staring me in the face, so I took a picture.
RF, anyone???
Rhuematism? I can't even spell it, but I sure can feel it. Feels like I'm getting on to 200 years old now, while I'm only 22.

Eric's video on cell phones and RF radiation from their towers.
http://www.youtube.com/watch?v=p8pQCykblNw

itsu · « **Reply #1127 on:** April 29, 2013, 10:07:35 PM »

Quote from: Hoppy on April 29, 2013, 02:36:17 PM

Important information still needed: Details for winding the air cored choke L4, the value of C3 and the primary winding voltage on T1.

Nice build Hoppy, and good questions.

For the value of C3, could this not be the flyback internal capacitor which would be between 1.5 and 3nF?

http://ezinearticles.com/?Understanding-Monitor-Flyback-Transformers-Internal-Capacitor&id=469722

Regards Itsu

Vortex1 · « **Reply #1128 on:** April 29, 2013, 10:36:11 PM »

Cpacitor C3 is the yellow disc at 1:40 in the Ikako video. This does not say there is not a capacitor also in the flyback.

I have traced out all the wiring in this video and it conforms well to the schematic "_00002.jpg"

MenofFather · « **Reply #1129 on:** April 29, 2013, 10:36:19 PM »

Quote from: anandml on April 29, 2013, 04:25:57 AM

Akku or dally device replication details present in this image. please anyone translate this image it maybe helpful for all..... I got this file from TUNGUS-TK video. I think now this file is removed by author from the video part

Tungus-TK is not Aukula, somebody make mistake and combine Akula video with Tungus-TK schematic. Tungus-TK not claim, that it have overunity.

T-1000 · « **Reply #1130 on:** April 29, 2013, 11:21:52 PM »

Quote from: Hoppy on April 29, 2013, 02:36:17 PM

I have attached a photo of the coil / spark gap, transformers and transistors / heat sinks I will be connecting up for my Chibinidze device replication.

Please let me know if you will need help with tuning as it is tricky part when you need to have resonance in series on same air core transformer...

Quote from: MenofFather on April 29, 2013, 10:36:19 PM

Tungus-TK is not Aukula, somebody make mistake and combine Akula video with Tungus-TK schematic. Tungus-TK not claim, that it have overunity.

The circuits are different, the description and schematics in the end of akula's video are not of his as well. The only thing what relates those two is the effect inside of coils.

P.S> Who seek knowledge may look on this video of Eric Dollard history readings - http://www.youtube.com/watch?v=UA2tLgL0HqE

NickZ · « **Reply #1131 on:** April 30, 2013, 03:02:20 AM »

Tungus is not akula0083, and someone placed the wrong diagram in the end of the two videos. The right diagram is supposed to be the one that is hand drawn, but who knows for sure. Why was the right diagram removed, or not shown, or is the hand drawn one even the right diagram?
Who knows anything for sure. This all smell fishy to me. As the video from akula is clearly trying to show a self running device.
Could the point be to steer us all in the wrong direction? So, that nobody will be able to replicate it. Maybe it is a self runner, but someone doesn't want that to be known, and this is all about that?
Any way, I've decided to wait and see...and give this some time, for the dust to clear.
But, in the mean time I'll continue with changes on my previous build towards this unknown direction, while getting nowhere, quick.

T-1000 · « **Reply #1132 on:** April 30, 2013, 04:06:51 AM »

Quote from: NickZ on April 30, 2013, 03:02:20 AM

But, in the mean time I'll continue with changes on my previous build towards this unknown direction, while getting nowhere, quick.

There is one direction... To see what happens when you have katcher/exciter effect meeting current on series quarter wave resonance and making standing wave where voltage is 90 degrees to current and when katcher/exciter coil is inside of current providing transformer.

NickZ · « **Reply #1133 on:** April 30, 2013, 04:46:29 AM »

@ T-1000 and All:
Ok, just how would you go about it? lets say that you have a working Exciter on 12v, and 1000mA.
Trying to keep the akula device in mind for this, not the other one. As I don't want HV spark gaps in my house making noise, creating ozone, spewing RF, and affecting things.

In my case a LS 3.0 circuit, can also function to give pulses to an Exciter air core/coil.
What would be the next step?
Would you use a yoke, for the primary/secondary, then further going to an Exciter air core, with an inner coil, with or without the aluminum or copper tube with the slit?
The akula device uses an air core with another inside air core, without the slit tube.
So, the slit tube is NOT needed.
As you can see I'm confused! So, if anyone can give us a hand, please do so.

BTW: Grum, I don't know about what you are currently working on, but, with my device if the polarity between the primary and the secondary is not right, it won't work, at all.

NickZ

Hoppy · « **Reply #1134 on:** April 30, 2013, 08:56:49 AM »

Quote from: T-1000 on April 29, 2013, 11:21:52 PM

Please let me know if you will need help with tuning as it is tricky part when you need to have resonance in series on same air core transformer...

Thanks, I will give you a shout if it shows any sign of life - without the 'X' wire of course.

Hoppy · « **Reply #1135 on:** April 30, 2013, 01:01:32 PM »

Attached is a photo of the complete build. As expected, there is not a glimmer of light from my 40W lamp I've tried many cap values in place of the 0.5uF and spark gap distances to no avail. The oscillator, flyback and spark gap are working fine at an oscillator frequency of around 64KHz. My transistor base resistors are 2K2 and spark gap cap is 550pF. Transistors are MJE13005.

I'm going to try the 'X' wire next - wish me luck

T-1000 · « **Reply #1136 on:** April 30, 2013, 02:25:14 PM »

Quote from: Hoppy on April 30, 2013, 01:01:32 PM

Attached is a photo of the complete build. As expected, there is not a glimmer of light from my 40W lamp I've tried many cap values in place of the 0.5uF and spark gap distances to no avail. The oscillator, flyback and spark gap are working fine at an oscillator frequency of around 64KHz. My transistor base resistors are 2K2 and spark gap cap is 550pF. Transistors are MJE13005.

I'm going to try the 'X' wire next - wish me luck

What is your choke wire length?
The resonant frequency wave length of it is ~ by wire length * 0.7, the current coils total length should be 4 times less with 4 times wider wire for quick resonant condition(resonance in series on same transformer with standing wave)...

Also to understand effect the following circuit needs to be studed closely: http://imgbin.org/index.php?page=image&id=13184 - C1L1 resonance in paralel, L2C2L3 resonance in series, L2L3 wire lenth ratio 4:1 , everything on single air core transformer.

dllabarre · « **Reply #1137 on:** April 30, 2013, 03:10:38 PM »

Quote from: Hoppy on April 30, 2013, 01:01:32 PM

Attached is a photo of the complete build. As expected, there is not a glimmer of light from my 40W lamp I've tried many cap values in place of the 0.5uF and spark gap distances to no avail. The oscillator, flyback and spark gap are working fine at an oscillator frequency of around 64KHz. My transistor base resistors are 2K2 and spark gap cap is 550pF. Transistors are MJE13005.

Hoppy
What did you wind the choke wire on? ferrite rod?
DonL

dllabarre · « **Reply #1138 on:** April 30, 2013, 03:16:47 PM »

Quote from: T-1000 on April 30, 2013, 02:25:14 PM

The resonant frequency wave length of it is ~ by wire length * 0.7, the current coils total length should be 4 times less with 4 times wider wire for quick resonant condition(resonance in series on same transformer with standing wave)...

T-1000
Do you mean the total length of both 80 turn coils added together?
DonL

Hoppy · « **Reply #1139 on:** April 30, 2013, 04:34:40 PM »

Quote from: T-1000 on April 30, 2013, 02:25:14 PM

What is your choke wire length?
The resonant frequency wave length of it is ~ by wire length * 0.7, the current coils total length should be 4 times less with 4 times wider wire for quick resonant condition(resonance in series on same transformer with standing wave)...

Also to understand effect the following circuit needs to be studed closely: http://imgbin.org/index.php?page=image&id=13184 - C1L1 resonance in paralel, L2C2L3 resonance in series, L2L3 wire lenth ratio 4:1 , everything on single air core transformer.

Thanks T1000. However, I'm sure that there is not enough power from the flyback for the performance shown in the video, even with a tuned setup. As you probably have more experience in tuning than me and as this circuit is an easy build, give this setup a go yourself and see if you can light the lamp as in the video without an 'X' wire. It does work better with L2 reverse connected in relation to L3, when I can at least see some ringing spikes on T1 primary, although again no flicker on the lamp.

News:

User Menu

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY (Read 11881870 times)

Hoppy

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

itsu

Re: Kapanadze Cousin - DALLY FREE ENERGY

Vortex1

Re: Kapanadze Cousin - DALLY FREE ENERGY

MenofFather

Re: Kapanadze Cousin - DALLY FREE ENERGY

T-1000

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

T-1000

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

Hoppy

Re: Kapanadze Cousin - DALLY FREE ENERGY

Hoppy

Re: Kapanadze Cousin - DALLY FREE ENERGY

T-1000

Re: Kapanadze Cousin - DALLY FREE ENERGY

dllabarre

Re: Kapanadze Cousin - DALLY FREE ENERGY

dllabarre

Re: Kapanadze Cousin - DALLY FREE ENERGY

Hoppy

Re: Kapanadze Cousin - DALLY FREE ENERGY