Quote from T-1000:
   it included 2 parametric circuits with opposite polarity connected together and each leg involves resonance in parallel+standing wave+resonance in series creating surge right on standing wave pin point where Voltage from one coil meets Amperage from another and generates excessive effect...
 
   What does this mean, I've heard you say it many times, but I don't understand how to do it. Can you draw a diagram and be more specific???
   I'm not concerned about the self running aspect for now, but,  to focus on the actual cause of making a big output, from a small input source. Who, if anyone, has done what you are mentioning?

   T-1000, Verpies, and All:
   I think that we really need to focus on what is making these devices work.  Let's just forget about the voltage source, inverter, and first rectifier, for now. As well as the feed back coil, cap, and second inverter. As these are not what is making this device produce an unconventional output. So, what is left? That is what we need to look into...

I tried to explain all these circumstances from my point of view what might make devices work (that still needs hard evidence with independed experiment) starting with post in http://www.overunity.com/12736/kapanadze-cousin-dally-free-energy/msg357338/#msg357338

From my view what is essential is to have there 5 things at once - resonance on paralel(L1C1) in primary, feedback from secondary to flip-flop circuit for breaking power input when secondary is starting to draw current so coils stop affecting power source, on the same air coil to have quarter wave resonant frequency between choke and secondary(L2C3L3) and resonance on same frequency on seeries and most important - creating standing wave between choke L2 as voltage source and L3 as current source. From the point where they both make standing wave you have shockwave what needs to be utilized by the load.
These all conditions are critical and need to be precise so with this environment you create something what is not in conventional physics...

  Void, I just read you post that you mention in your last post. I had missed it before, I will consider it.

Hi Nick. What I am talking about with the primary series resonant circuit and how the choke would likely be tuned is not theory. I was basing my comments on the hand drawn schematic which Akula's previous demo board seemed to follow fairly closely. In a prior video Akula showed some tests with driving a series resonant circuit and how it produced high current. This is the same primary circuit configuration used in the hand drawn schematic as well. Since Akula seems to have followed the hand drawn schematic fairly closely (except for maybe some parts the main coil configuration), then I am pretty certain that is how he set up the primary circuit in the previous Akula demo video.

Using a series resonant circuit for the primary circuit would require that your transistor driver circuit be frequency adjustable. You would have to set the frequency of the transistor driver circuit to run right at the resonant frequency of the series resonant primary circuit. This resonant frequency is easy to find if you have an adjustable sinewave generator and an oscilloscope. If you don't have an oscilloscope, you could use a clamp on type ammeter over a wire in the primary circuit and adjust the transistor driver frequency until you read maximum current. You don't need to care about an accurate current reading as you are just adjusting for maximum current flow in the primary series circuit. If you don't have a frequency adjustable transistor driver circuit, then it will be tougher to tune. You would have to vary either the total inductance of the windings or change the series capacitor value, to make the primary resonant frequency match your transistor driver frequency . That is not so easy as just adjusting the frequency of your transistor driver to match the primary resonant frequency.

If the choke coil in the main coil assembly is parallel to a capacitor as shown in the hand drawn schematic (tank circuit), then this parallel tank circuit would probably be tuned to the exact same frequency that you are driving the primary at, which is the primary's series resonant frequency. It looks like the main output coil secondary winding in the hand drawn schematic is not tuned for resonance, and so the goal with it may well be to just wind it with magnet wire with a whole lot of turns so it steps up the secondary voltage to a high enough voltage to light the lights even when the lights are connected in.

That all seems fairly straight forward over all. So what might make the circuit produce over unity then? Well, the choke coil configured for parallel resonance with a capacitor and with the choke coil placed inside the other coils might contribute to some sort of boost in performance, but it would be hard to see how that might give over unity by itself. That aluminum sheeting that is wrapped around the coil form, which is between the choke coil and all the other coils, might be contributing something unusual to the whole arrangement, but who knows.

I think the best approach to try to set this up would be to build a frequency adjustable transistor driver circuit so you can easily drive the primary series circuit right at its exact resonant frequency. This resonant frequency may change a bit when you add or make changes to the other coils, so having a frequency adjustable driver would allow you to fine tune the driver frequency as you make any other changes to the whole coil assembly. Once you get your coils wound and you find the right driver frequency, you would then tune the choke and parallel capacitor to match the driver frequency you are using. There may be a bit of a back and forth there as you tune up the choke tank circuit, as it may impact the primary resonant frequency as you change the choke tank circuit tuning. Having a frequency adjustable driver circuit would make the tuning much easier here as well.

The question I would have is, is that aluminum sheeting connected to anything such as another coil, or is it just placed in there with no connection? Without having more specific details I think the best you could do there is experiment with a few different ways to connect the aluminum sheeting in, and compare to leaving it unconnected. I will see if I can find some time to do some experiments with this sort of setup over the next month or so. I am also interested in trying this out.

  quote:
  " You would have to set the frequency of the transistor driver circuit to run right at the resonant frequency of the series resonant primary circuit."

  Ok, I get that. Maybe the transistor, or drive circuit output, can also be frequency tuned by using an AC wall dimmer, along with variable capacitor from a radio, etz... and the light output from the leds (that I use on top of the small inductors) can be used as indicator lights, which can help to tune for the higher output. 
Just a thought.
 Otherwise, I know that this may all be like trying to find a radio station, on a radio that has no tuning knob.

  EDIT: After I posted the comments above, I found this in another forum. It is from a Tariel Kapanadze patent, and I thought that it would also fit in well right here:

  Well then, with that overwhelming evidence, it looks like you guys have more than enough proof to start your own thread now.
  So that the people who would really like to move along and further advance on these threads, can do so without any more negative, disruptive, and ludicrous comments. Your true intentions must be now just to troll.
So it seams...

                                               "Don't feed the TROLLS"
 
    New thread:

   "ALL FAKE KAPANADZE REPLICATIONS".

After I posted the comments above, I found this in another forum. It is from a Tariel Kapanadze patent, and I thought that it would also fit in well right here:

It is common practice in many patent applications to write about the device and how it works in very obscure terms, to make it hard for people to figure out exactly how to replicate the device. This also seems to have been done in the Kapanadze patent applications. I can't make out a whole lot out of what is said in the Kapanadze patents applications, although I should probably read through them again and see if can get at least some idea of how his devices are supposed to work. It is mostly indecipherable to me however.

Dear NickZ.

I have been following this thread quite closely of late because there are many similarities to the devices we are currently working on.

I DO have to agree with the comments that Void has recently made. One of the most important "pieces of kit" you will need to persue any of these projects is an LCR meter.

I know very well they are expensive, it took me two years to save for one. and believe it or not it was imported from the USA!! But for finding resonance easily I'm afraid you will need to get one.

I obtained most of my "kit" from a local training school. I went in "cap in hand" and explained what I was doing, but don't mention Free energy!! And believe it or not they gave me a scope and a frequency counter!! So give a few places a ring, you never know?

BTW this is the site I visit for LC resonance calcs........http://www.whatcircuits.com/lc-resonance-frequency-calculator/

All the best, Grum.

   Grum:
   Thanks for the info, good to hear from you. Although I do appreciate your ideas and information, I am not able to follow through with it. Someday these things may come to me in any case. 
I'm good at finding my way in the dark, with my heart guiding my way, and can find my way even in the worst storms.  But, for now, I must find a horse that I can ride. As Dr. Stiffler once recommended to me.
  As you can see from my pictures, I've done quite a bit, while spending, well, Zilch.
  I will upload some more pics and videos, as soon as I can find my camera to pc cable, which is lost in my house.

  Please, don't give up on your project, we all need to get onto the real deal here, as this is not just too good to be true. It is true, and not to be ignored. Mark my works... I am a permanent fixture, not going anywhere, you'll see.
  I'll return to the other thread, when ever they stop peddling fake wares, as I can't deal with that, although they seam to get around.
                               What goes around, comes around...