Hi Stefan and All:
   I was watching this video today of Kooler and his HV system, might work for something like is needed to charge the quartz sand in the reactor,  looks and is kind of dangerous though. Can't get too close to it.
    http://www.overunityresearch.com/index.php?topic=418.0

Hello Thomas,

Hartman found a network and an underground river, with the help of profesonal.
sifted quartz sand in small pieces
heated it to 100% dry
I loaded the "reactor" by Tesla transformer with 6000 volts
This picture shows what the voltage received from the reactor
Synchronize pyramid by cutting small pieces of "condenser"
I got about 250-260 mV AC
Multimeter is connected between the "plus" and ground piramide
the same  teminals a fan connected
after I turned it by hand
fan rotates one, two seconds
and stops
what happens, where I'm wrong?
Here is a video: http://www.youtube.com/madsatbg#p/a/u/0/r3I3s01A-zc

at best wishes
 madsatbg

Did you get the same reading problems with your multimeter and the sand?
My video (in english with explanations inside):
http://www.youtube.com/watch?v=aWgscVRubFU

@Pascuser and all who do measurements:

Since some time I try to get electricity out of the electro smog surrounding us. While building different antennas and circuits I observed the following:

Whatever antenna I built, I always found 0.5 to 1.8 Volts when measuring with a good Multimeter in the AC setting, specially when I provide a good ground connection.

So, one has to be very careful when interpreting such results. Unless you live in a very remote area, you are surrounded by mobile phone towers, WLAN-transmitters, Radio and TV stations and power lines and you can see some Voltage whenever you have some sort of antenna on one Multimeter probe and a good earth connection on the other Multimeter probe in the AC setting. When you use a high frequency diode you can also see it in the DC setting.

It is easy to measure some Voltage, but it is very difficult to get some decent Amperage. So, the received "power" (Watts) is very little with a crude antenna.

A further interesting fact is that your body can either act as an antenna or as "ground". So, build whatever antenna you want (e.g. use a short wire), connect one probe of the Multimeter to this "antenna" and touch the other probe of the Multimeter (wetting your fingers will help) and you will see some Voltage in the AC-setting (0.5 to 1.8 Volt). The "better" your Multimeter is, the easier it will be to see a Voltage in the AC setting.

This post does not say anything about the Trawöger pyramid, it is just a reminder that electro smog is everywhere and influences measurements in the AC setting of a sensitive Multimeter. Trawöger claims up to 15 Watts from his pyramid, which can not come from electro smog according to my hobby research into electro smog. But the measurements I saw in the forums done by replicators with their "generators (copper tube coils)" look very much like electro smog to me.

Greetings, Conrad

You made my day good and now i will drink a beer :-)

thanks Thomas
I am so happy тоо,when you think that my pyramid
work and thank your I believe in free energy and people who openly share
 
I join you and drink a beer for success and free energy

cheers  madsatbg

p.s.will follow your advice

To madsatbg:

Congratulation for this big step on the way to sucess !!!

You are the one with the golden fingers !!!

@Madsatbg.Align the pyramid exactly North , and then turn the pyramid 1 - 2 towards EAST . That is 1 or 2 degrees CLOCKWISE as seen from above . This is based on aircraft type compass where numbers are use . North is zereo and east is 90 degrees , so starting from north , plus 2 degrees means 2 degrees towards the east . For those who are confused , the photo  in the above post is of the v6 pyramid from 5 years ago .
 Could you please confirm if your inner pipe is of 10 mm or 15 mm diameter?

Could you please confirm if your inner pipe is of 10 mm or 15 mm diameter?

Hi neptune,
Yes, I use 15 mm inner pipe.
I use 20 mm PVC tube for "capacitor", but I filled the pipe with
Straw PU-Foam

regards

@madsatbg
Thanks for telling us the sizes.
I live in Canada, and even though we use metric for street signs,
building materials are still in inches. 
The 10mm tubing is 3/8 inches here but is only available in rolled up tube which must be straightened.
16mm is 1/2 inch copper tubing and is commonly available here.
30mm is 1 inch copper tubing and is commonly available here as well.

@Trawöger  can I use the 16mm tube inside the 30mm tube with the same lengths you used? 
Also can we use 20mm PVC pipe for the capacitor?  That is 3/4 inch pipe and is common here as well. 
If so that will make things very simple for us in  Canada and USA to replicate.
If not can you work out any changes we need make for here.