Привет всем !!

OBTAINING FREE ENERGY FROM NIKOLA TESLA TRANSFORMER BY TIGER2007

On the Internet exist a lot of documents which saying that the Tesla transformer or T.T is a power source, but nowhere did not told about how to correct adjust it. Let's try!! T.T (Tesla Transformer) is the simple device which the ordinary school boys can make, but for adjusting and trimming T.T at least an 2 channel oscillograph and signal-generator are necessary equipment, for example self-made PWM generator on TL494. The description of schemes on TL494 can be found easy on Internet. This generator is good because it has a possibility of separate adjustments of dutycycle and frequency.

And so we will begin!! Everything what is necessary is a plastic PVC pipe and 40 meters of a Magnet or enamelled wire, also some high-voltage impulse capacitors. For example there is a plastic PVC pipe 40 cm in length and 11см in diameter and 40м Magnit wire - 0.3mm diameter. Winded on a pipe we got a winding 34.5см in length from 115 turns. Now we need an inductor (primary winding). We will follow Nikola Tesla recommendations and we will measure for the pur primary a piece of the same Magnit wire four times more shortly, than for the secondary winding – 10m. Diameter of  primary coil should be at least 1,5-2 times or even more bigger than diameter of secondary.

Let's say for example we have found a piece of plastic pipe 14 cm in diameter, we winded the primary on it. The primary winding is 70 mm in length from 22,75 turns. Everything we got, so now we will fix our design, fastening the primary. It’s desirable for making so that it could be moved on both sides several cm. ATTENTION - WE DO NOT SPARKING ANYWHERE.  Let's collect the elementary scheme (1), we will connect an oscillograph through a sensing loop on secondary,  also signal generator on the primary and we will play with frequency and duty cycles of impulses. Done !! What did we seen? We have seen distinct impulses followed with a dumped ringing oscilations of tested coil. Let's now adjust frequency and duty cycle of generator so that distinctly we can see 2-3 starting impulses and 5-8  dumped ringing.

Now we will do a little count. We will search for exactly one frequency, ONLY ONE FOR RESONANCE, among thousand others, namely that frequency on which wave-length is 4 times more than a length of the wire which has been winded in coil. For example  40m multiplied on 4 – we receive 160m – which was required wave-length and there corresponds exactly frequency 1,875MHz. Here I intentionally didn't considered shortening factor of a wire, as a rule, wires comes from unknown brands and this velocity factor many times isn't known. We will see everything on oscillograph.

Further we will connect on secondary coil, variable HV capacitor and do adjust-ments, or fine tunings by soldering additional capacitors in parallel to main HV variable  capacitor (2). Capacitors will be in units of pF or maybe – in tens of pF. It is possible to take variable capacitor from the old receivers, the truth is, we need to measure his capacity and to find appropriate high voltage capacitor closest measured value, or to make one. Working voltage of the capacitor should be not less than 10KV.

At some instant time we will see on oscillograph increase in amplitude of free oscillations and what is the most interesting – damping of waves will be very very slow-ly. It is a mode of a standing waves in T.T – on the ends of our coil now exist two antinodes and a signal almost without loss have reflected from the ends of secondary contour. There is a free energy and we have got something at last.
 
Now we have taken a little free energy. We will connect one channel oscillograph  probe on terminals of primary and observe carefully (3.). We will  see – start impulses of generator and dumped oscillations of the inductor at very high frequency. Here is very usefull two beams oscillograph, with one beam we will supervise oscillations in the primary coil, with other oscillations in the secondary of T.T. Trimming primary coil frequency by adding additional capacitors, we will get summing capacity about 100 – 200pF. At some instant time we will see increase in amplitude of oscillations, as we  approaching the resonant frequency of a primary contour, we will try to move primary coil along his axis. At the moment of coincidence of frequencies and phases of oscillations between primary and secondary coil we will observe the following …. In the primary coil dumped oscillations will be clearly visible. In a secondary winding …. We do not trust our eyes!!!! Dumped  oscillations were turned into the increasing oscillations!!! And the amplitude in the secondary considerably grew up. On two beam oscillograph it is clearly visible … Appear like primary dumped oscillations pushing oscillations into secondary and their amplitude in secondary grows during some time,as a rule 3-5 oscillations, then starts to fall very slowly. Now we have everything, we have free energy. 

Well now is possible to disconnect signal generator and to connect spark-gap on our primary.

...........................
Notes:

Primary coil should have good Q-factor (quality factor), and it’s not necessary to seek to big factor of transformation.
The question about output of energy is a separate subject.
It is necessary to tell you that everything that here was written – was repeated.

EVERYTHING WAS CHECKED BY TIGER2007 - 14. 11. 2010.

The question about output of energy is a separate subject.

Yeah, but that is where it gets interesting! All that Tesla primary stuff is known.
Simply hanging a load on the output without extraction concept of some sort will kill the resonance and just load the source down and that's what everybody mindlessly does.

opposite wind 1/4 wave current transformer i n s i d e secondary

Hi!

Zeitmaschine are you reading at moment?

Someone has posted a patent (application) not more then 2 month ago. I suppose it was here, and it was Zeitmaschine.
Content was, a array of Tesla-HV-Secondary with INSIDE (third) low voltage current coil.

Does anybody show me the way to that patent again?

Thanks!

@all1

I need help for a Russian translation of some parts of the Green Box video.

1) At 7:55 before they connected the ground wire to the water pipe, the fat guy with black vest measured the voltage on that pipe and saw 06.4 volts. This was before any grounding wire was added to the pipe. This is very important because when he measured that, the other fat guy came and took the probe in his hand to stop the measurement process. You can also see a stray thick wire is lying right next to the base of the water pipe. WHY??????????? This is of concern. Why would he measure 6.4 volts. It could be 6.4 volts but it could also be pulsing at 100kHz at several amps or more and you wuold not even notice it existing as a rider frequency that can permeate the complete system as an added energy source.

2) At 22:00 they had just connected the radiator ground wire and started up the device but the bulbs were not well lit and at 22:30 the fat guy measured the amperage at the ground wire and only spoke out the reading. What was that reading?

3) After that there was a lot of commotion while they figured out what was wrong. Then one of the guys unscrewed a few bulbs and three of them were lit up and the fat guy read again the amps at 23:38. What was that reading and if possible can we have a general idea on what they were talking about?

4) After that at 23:53 the fat guy and TK went to measure voltage across one bulb it read  -1137, -170, 393, 319, 238, 100, 061, 096, 030, 068, 085, 070, 043, 085, and during all these great voltage fluctuations we could notice the weak bulb brightness fluctuations. What were they talking about?

5) TK seems pissed off and he grabs the chairs holding up the bulbs and moves it and at 24:30 he gives a wire to the other guy. What did he tell that guy to do. (Later we see the guy connecting that lamp wire directly to the  water pipe).

6) At 24:36 TK does some connection changes at the green box. What was he saying.

7) At 43:33 the guy that put the wire  onto the water pipe tells TK something and I heard the word "negative". What was he asking.

There is so much in the green box video we do not know simply because we do not understand the language. Ideally we would have need for a timed translation so we can put that video into full context.

Something went wrong when he put the radiator on and during that commotion things may have been said that would not have been said otherwise.

My other question is when they put the radiator on and before they unscrewed the bulbs, at 22:17 when they tried the rad as ground and when he turned on the green box switch, why was there only one bulb lit? If those bulbs are in parallel, each one should have been lit to 1/5th. We need to listen before this time stamp to hear if they are talking about unscrewing some bulbs that they could have done before the rad test.  But I don,t think so if the video was a normal progression of the events.

This is very important information and it is really too bad that I cannot speak Russian. I heard a few Armenian words in this video. Can TK speak Armenian?

@all2

I still have not received my TO3 zener diodes. I  have been doing alot of experiments with the transformer and diodes. Also some may be interested in what @lasersaber had been up to here;

http://www.youtube.com/watch?v=Zt5zulKQ1XE&feature=youtu.be

wattsup

Except from the part where the woman interviews him (russian), they actually speak georgian language (not russian) all the time.
Somewhere on the first 100 pages or so of this thread (page  8   i posted a rough translation that a georgian person i know was so kind to do.
http://www.overunity.com/7679/selfrunning-free-energy-devices-up-to-5-kw-from-tariel-kapanadze/msg189159/#msg189159

I believe having read that one of 'TK's gang' is from armenia.

In the thread you give a link to, the following translated comment is made: "Bring lamps, we must check the potential difference between earth and water supply"

Question: Why should there be enough difference in potential to run the light bulbs. Possible answer: Because the water supply pipe is connected to live mains or some other potential above ground!

@wattsup,thanks for lasersaber link, the circuit he has posted looks very promising and with a few tweeks could work for larger output if scaled up using 1:10 transformer and larger cap. Transistors doubled or trebled to withstand load.Lots to try.
ps. If Kapanadze gens work like this it explains a lot, earth required and 50hz input and output.
Regards
Keith

Of course it is a real bad idea if the pipe is not insulated from earth 

And the pipe would then of course also carry 'non-conductive water' right?