Bart
Its Not Dead ,Its Evolving......................
I think I heard a Heart beat??[In the Mens Bathroom 
]
Scary !!
Well there will be lots to discuss soon.............
Chet
PS
I would love to hear what Wesley has to say about Shokacs
Pic! BTW ShowKac NFG ON The VID IMHO
Quick :
As I'm ruining out to make some money.but I'll be back
wire inside coil is capacitor
You have factor of capacitance between wire and tube but you have............ o fu.k
.......... dont take me for my tong...........
I think I have got it.
1. capacitance between wire and tube
2.capacitance between winds of wire ( each individual circle of wind- between themselves)
3.capacitance between tube winds ( each individual circle of wind- between themselves)
4. if you connect tube than you dealing with bifilar is'n that one of possible factors of controversy of TK coil?
depending on how you connect the ends of the tube !!!!!
Whatever Shokac did it does not matter for now because I did not read it nor analyze it as of yet.
what matters is that I haver got a hint.!!!
I'll Be back
Wesley
PS: capacitive coupling ( Vladimir Utkin- my Hero)
think about it
Ok I'm back instead of posting new post I just continue this one
Lets think.
concentric cable= wire in copper tube.= shielding
Picture by Shockac is wire in coper tubing
1.We can threat it as coaxial cable only if we ground shield
2.Coaxial cable has SW(standing wave) and SWR (SW-ratio) is the measurement of power flow of EW.(electromagnetic Waves)
When energy can not go out completely because of impedance
of coax than part of this energy is reflected and returned back
SWR 1:1 is ideal for coax.
With the length of the coax you may notice with your hand warm spots. The spots are the concentration of energy points with SWR at high. Part of this energy is lost as heat in these points. the biggest impact is the energy returned to the power source ( Power transistor or tube or circuit)
Transmatch/ antenna tuner/ output resonance circuit
is the impedance matching device to tune impedance of the load(say e.g.antenna) to the impedance of power amplifier( say power transistor or tube with resonance circuit)
In most common scenario it is 50 ohm standard.
wire in the tube is almost ideal coaxial cable (but does not have 50 ohm impedance. And only if the shield is grounded.
So let's say Shocac show picture of:
a.coaxial cable...with high SWR
b.coaxial cable with out connected ground
c.concentric capacitive coupling component
d.bifilar.
e. leaky coaxial cable ( if we make holes in geometrical spacing in the inner service of the pipe so the holes are directed to the main primary coil.)
Note: do not confuse yourself with the word "primary"
"Primary" in here does not mean "primary winding"
but does not eliminate it's role as primary winding if one want's to use it as "primary winding for the circuit "
if "a"
than
-shield will prevent wire inside to interact with the main primary coil inside
-but shield will interact with main primary coil inside The amount of SWR will determine
hot spots of power and the number of hotspots( edys current in tubing)
- part of the energy will be reversely reflected to the source as BEMF cosing phase shift
- interaction will create response of the main coil(the one inside tubing)only in these points ( very interesting)
if we go further we may drill holes in the place of hot spots to let energy out and interact with main primary coil
Note:The problem I see in here is stability of the frequency as the position of hot spots and/or holes depends of frequency delivered
if "b"
than
Outer shield will no longer be shield but second plate of capacitor. Question than is how the electromagnetic wave is spread and or what is the characteristic of propagation
(Next Sunday I will discuss it on scientific meting)
-there will be secondary electromagnetic field created around the tubing, as the reflection of that what is going on in inner wire.
if "c"
than
-this is only pointing to the existence of such capacitive coupling in any of these examples, but the role of such coupling in anyone of these examples will add to different effect as the end result.
-So we have capacitive coupling between two coils from which the tube is not connected anywhere at all .If we deliver frequency of length equal space between wire and tube than
"maximum every sign shape in within the tube will create hot-spot om the tube.but than frequency should be in GHz( example 1.2GHz= wavelength 23cm) In reality we do not deal with such diameter of concentric nor coaxial.Even diameter of coil by itself is nowhere near this in TK device.
Note: square wave signal from generator contains singular sign wave components from low to GHz
in each of the square shapes so we may or may not be dealing with interaction of components in regards to that interaction
That might explain why Square shape was utilized at the beginning of by everyone including me and TK.
-but we have to remember that almost 100% of direct interaction of the wire is limited only to tubing and tubing is direct interface to anything ( if any)
id :d"
than
wow......... it is getting interesting here.. uch.............
remember that controversy with gas? ..........
how about if we connect the wire inside the tube with edge of the tube at the end......
and than we use electrical tape to rap an" just the insulation of the wire without copper inside" for others "
to believe that there is"outgoing connection from tubing coil.
what did we achieved is bifilar and than we have to play with to ends inside green box.
-and what if we in did made connection of end of the wire with end of tubing... we will still maintain capacitive coupling altered by shape ,frequency (properties of signal delivered)
-and what if instead "fake wire"(insulation without the wire) we take real wire but not connect this wire to point of connection of tube and inner wire....
now we can play with three ends
one is wire inside tube
second is the tube end
third is the real outgoing wire
lets see what happened if we never connected anyone of them
but rap them together keeping them insulated( and fake connection by using electrical tape)
we than-
WE HAVE CREATED 3WAY CAPACITOR or three plates capacitor something like capacitive bridge.. or capacitive switch.
please picture
(from the left side wire connected to plate)
than
(plate inside-in the middle with wire connected)
than
( from right side wire connected to third plate)
for me it is that what is going on with
earth(plate at left)
my piece of wire e.g antenna at say 100f high)
and ionosphere
the difference of potential between earth and the ionosphere is 36000V so the antenna (in the middle) represents responsive charge with regards to distance to one of them
note" the problem that I have with that philosophy id that capacitive coupling relation is significant between wire inside tube and tube but is small between the third wire ( if one exist)
As the point of
"contact=diameter of third wire= gauge"
represents small square mm area
but concept is interesting as this would create sort of KBE if "capacitive transistor"
if "e"
than
leaky coaxial cable is very much known in the field of communication it interacts if improperly installed or power level is to high with everything in subways cosing a lot of problems
Please find by yourself in the most comfortable language information about leaky coaxial cable
