Zeitmaschine: It cannot be coaxial cable because that would be electromagnetically shielded. It has to be heavily insulated (against static) high voltage cable.
High voltage cable is quite capable of handling a couple of kilowatts safely. Say 10 amps, Maybe 15 amps at mains voltages.
It may be coaxial cable with the braid stripped off. TK does this all the time.

Since I have this photo just at hand: It shows a very nice work of Mr. Flim-Flam!

Most likely the whole device is accommodated in box one - and only in box one. Box two passes the grid power. The three switches are there at best to switch the power on and off. Box three passes the output power through the dummy coil to the lamps. Box four passes the ground cable to box one.

No noise, no heat, no vibration, no radiation, no adjustments, no nothing. Any further questions?

Yes: What fits in a box approx. 20×20×10cm that can generate 2KW of electric power?

FreeEnergyLT

Pulsed transistors producing radiant energy maybe?

Anyone think this can help
Houston, that just the proper order of operations when working the equations that include Q. L which inductance is in Henrys, that's always ideal. Winding resistance is the loss, and if you use a 1000 feet. The primary of T1 is just over 1 foot long, and 1000 feet of 9AWG wire has 0.8077 ohms of resistance. So, if XL = 1 ohm at 1MHz, Q = XL/0.0008077. Q is only a figure of merit, I've heard it called Quality, Flyback Value, and a few other things. Once, you've calculated the Q, you've included the wire loss. So, if the winding resistance were 1 Ohm, Q would equal one.

I want to use that primary. But, it really looks like I'm going to have to decrease the power in the first stage in order to keep the cores from saturating in later stages. Saturation isn't really the problem anyway, with each stage a step up. The current per stage is lower and lower, the voltage is higher and higher. Current will saturate a magnetic core, voltage won't. Voltage will cause an eddy current when it breaksdown and causes are between granuals of metal that the core is composed of.

I solved the modeling problem, if you went to those links. I even know that I gooffed in the number of turns on T2 and T3. There's a design rule of thumb, and when I use it, I don't screw up. So, you're really seeing me flunk my own self test. Not completely because I know where my mistakes are. The Output Impedance of T1, is used to calculate the minimum inductance value of the primary required for T2, the output impedance of T2, is used to calculate the value of inductance of the primary of T3. The simple rule of thumb is that the inductive reactance of any resonant stage following the first must be at 2 times greater than the output of the previous stage.

Using ideal component values is typical in designing any circuit. Because, it gives you an idea of what the circuit will be operating like. You calculate losses once you've selected all of your components. One capcitor is not the same as another, and the quality has everything to do with it. If it's only good up to 100 volts and your circuit is going to be operating at 1000, you can't use no matter how many amperes it can handle. If it can handle 20KV, that doesn't mean that it's any good at 100 amperes if that's how much current is passing through the circuit by design. The leads will heat up once you get past 1 ampere. So, you'd need a doorknob capacitor. Some heat up internally due to the thickness of the plate and they can't the handle 1 ampere without heat expansion causing the value to change during operation. It's not a tuning capacitor, and it's not a controlled change, and will throw off your center frequency. If you wanted everything tuned to 1MHz, that capacitor won't stay the right value.

I don't believe that you understand the solution, or the problem. We have enough of the right components to operate that circuit design all the way up to 2.5KW with available components all day long, and well over Unity.
Well, I know this much, my wire diameters are fine. Ran a few calculations and T2 could work if you stacked 4 T-400-2, the dash two is a red core, and it's powdered iron. And T-2 if the winding pitch is adjusted to distribute the windings evenly winding on the stack as if it were a solenoid, and not using the cores for a toroid style winding, the primary of T2 can handle all of the energy and will only rise 3°C. That's ideal for lighting, especially the unloaded secondary design.

T3, most likely will require 1 to 2 more cores, even though that may not make any sense. The quartz tube coil at this point would be wrapped around the outside diameter. If you made the coil the smaller than that, it would fit inside cores and you would have put the light somewhere the sun didn't shine. I had said before that I would have to wind on the edge of one of these cores to actually calculate inductance per turn. So, it would be easier to wind with coated wire, and measure the inductance every few turns, until it reaches the proper value.

T1 is 1 to 100, T2 is 1 to 4, and T3 is 1 to 2 and the secondary is left open for the bare wire, and the bulb is just a gas at a pressure of 0.01 torr. Even though I had revise this somewhat, you do have the design rules of thumb.

Input voltage times 1.414 equals the voltage across the primary of T1, current times 1.414 equals the current through T1's primary.

Output impedance is then 10000 ohms. XL of T2's primary must be 2 times greater at 1MHz, or 3.18 mH. Then you multiply the current and voltage again by 1.414 due to the capacitor in parallel with T2's primary. T3's primary should be at 18mH. At that point, I would switch to MPP cores, or Metglas in the same arrangement as defined for T2. It should have a higher permeability in order to reduce the number of turns of wire required. Only MPP and Metglas cores operate cool enough, and Metglas should outperform MPP at those frequencies if the design request is sent to the manufacture for the core size and operating frequency. It would be custom and you would want it's dimension to match the T-400s.

Hi A.king, i just watched video 200W from stivep, the 100kw turkey, the 2kw from 2007, and all the ground are braided copper wire ( or aluminum wire ) like you said, could he want static discharges in the centre of a coaxial cable.

Static discharges are an unwanted byproduct at a certain point in any radiant energy device. TK grounded them. Someone has already posted an experiment on this thread whereby the disconnection of an earth caused his experimental device to go out of phase. This has happened to me also. We have already covered this point. The disinfo agents know this and dump clutter on this thread so the truth is lost many pages back. Look up radiant energy creation by Bedini and Bearden. You should spend a lot of time assimilating the concept. They have a patent issued on it. TK simply improved the concept. Tesla invented radiant energy. Bearden and Bedini should not have received that patent.

Hi A.king, i just watched video 200W from stivep, the 100kw turkey, the 2kw from 2007, and all the ground are braided copper wire ( or aluminum wire ) like you said, could he want static discharges in the centre of a coaxial cable.

For me it may be much simpler. He had braid left from dismantling coaxial cable so he used it.

They canceled 3 pages? ....

Leo48

Actually as I posted before, I have inside information. TK was panicking earlier this year because he needed braided wire for his device to work and his local suppliers had run out. I do not know if it was the high voltage part alone or the complete thing.
If you have static residue, you need a large area to help disperse it. Ordinary wire can leak static easily. The only answer is to do some experiments with earth grounding and see for ourselves. I am aware  that a simple static leakage can cause massive loss of power. Even Bedini could not loop his devices. Bedini shows videos of himself lighting ne2 bulbs from the floor and from his battery casings - so I think we have to be carefull about generalisations.

Eric Dollard pointed out that an extremely low ground path resistance is required like in his energy transmission experiment between S.F. and L.A.
The braided wire would exhibit lower resistance and provide higher Q factor for more VARs.
Interesting to hear that TK considers it essential to the functionality of his device. Thanks for mentioning that.

I have reviewed all the info and have figured it out. His patent does not have a HV generator, but has a frequency generator. So where does the HV come from .... think....
His device is most comparable to Dollard, Tesla's radiant energy, and Bedini- Bearden's radiant energy patent. It is not taught in physics.
I will not do an instructable because I am still working on it and there are too many negative forces watching this forum. Those who experiment will figure it out.
Put it this way - I am getting private messages which confirm what I am telling you.
So I welcome any new pictures or genuine video translations and information.

Well there is not that many possibilities.
Suppose that he does not use a standard HV generator with a high turns factor HV transformer.
Closest bet would be a resonant coil with a high Q factor much like how a real Tesla coil that manages to create that high voltages
but fed with low voltage like 12Volt -230 Volt to 2kV (Never seen anything like it however)
Another option would be voltage multipliers, cascade circuits, charge pumps but they would yield DC HV.
Electrostatic HV like in Testatika.
Electrostatic HV fields play a role in a couple of OU set-ups.