Triple Torque Amplification Theory:

The attached file has information of three ways that torque is amplified in one device.
1.)  Through layered stator and rotor core tabs configured and tested
to increase the torque by 238%
2.)  Permanent magnet assist: This approach doubles the flux flowing in
the area where the interaction between the stator and rotor core pieces.
3.)  Core material increase the flux flow over air core coils. 
Dr. Robert Holcomb talks about this as a large improvement in device performance.

I use all of these amplifications in one device.
I files have a lot more information of ways to improve electromechanical
devices.

Lunkster

Well i made it through the first 10 pages, but that was about it.

It is clear you have more learning to do about many things-( as do we all).
For example--you claim that the copper wire in a generator would run out of electrons after driving a load for some time, and you have come up with a theory that PMs suck electrons out of space, and throw them into the copper wire, which is why the copper wire never runs out of electrons. Fact is, no electrons enter or leave a circuit, as all conductors have their own electrons. So all the generator actually does, is pump the electrons around the circuit, load, and generator. In the case of DC, electrons flow out of !what you call! the negative side of the generator, through the circuit, and back into the positive side of the generator, where the motion of the magnetic fields within the generator, pump/push the electrons through the generator windings, and then back out the negative side again.

Now, the electron moves quite slowly through the conductors, but when you have billions of electrons all flowing slowly, then you have billions of electrons leaving the generator every second, and this number increases with size of said generator, or at what speed and load is placed on the generator.

So no, the copper windings within a generator will not run out of electrons, as you need a completed path in order to have electron flow.
And no, electrons are not sucked out of space, and thrown into the windings by magnets.

If you want an efficient motor, then make sure your magnets and coils are fixed (motionless), and have only the rotor turn.


Brad.

Brad,

Thank you for replying to my post.

What I wanted to convey in the first 10 pages, is that when using a hand crank generator is
that as long as you turn the hand crank, the electrons will flow to produce heat and light
in the light bulb forever as long as the movement is occurring by the hand.  I was saying that
the materials in the set up can not supply that many electrons for the heat and the light
from the light bulb by itself.  I am saying that the electrons con from the secondary source
of power.  That secondary source of power can be from the environment from static electrical
charges or from the zero point energy.

Why is this important for my free energy motor designs?

It is because one of the first questions people is to ask, how can the motor be a free energy device
by having more output energy than output torque that can run a generator to produce more energy
in the output?

So I work through several different electromagnetic concepts in this paper of how different energy
sources come into play in order to have a device that does not violate thermodynamics.

Each of the three amplification techniques use a different method of inputting external power
or power conversion technique into the device to achieve a final system where the input
electrical power along with these three amplification techniques can operate an external generator
to produce more output electrical energy than the input energy.

When I have time, I will try to make this more plan in this paper.

I did add a lot of information of what it took me to get to this three layer design.

The motor plan that uses three torque amplification techniques are on pages 96 through 196.

Again,  Thank you for your input,  I helps me out a lot to know what people are thinking.

Lunkster

Hi Lunkster.

In regards to a lightbulb (incandescent type), you need to think as the bulbs element as a choke point for the electrons.
This choke point creates friction, which results in heat and light. But once again, no electrons are lost, and none are gained. The existing electrons within all the conductors are simply pumped around the circuit.

As far as torque amplifiers go, then any successful device would be much appreciated by us all.


Brad

Brad

Hello Again
This motor works its way through several new theories that I developed along with some work other people have done in order to provide free energy in an open system to the world.  The main thrust of the motor technology is a new design that uses three torque amplification technologies in one device.  Each of these three technologies have the core material as one of the main reasons that each of these technologies can achieve torque amplification.  Two of these technologies amplifies the flux in the device which in turn produces more torque in the device. One of the technologies amplifies the torque from a constant flux.  This is a technology I developed and tested.

The first technology is the fact that a coil with an iron core will produce a lot more flux flow in it than an air core coil.  The way I use this is in a hybrid toroid coil that is operated in a way I have not seen before. It uses only a drive coil to stimulate the core material with no secondary or other coil for its performance.
The second torque amplification technology is a layered rotor and stator torque active area.  I have tested a single layer of core disks that only has 42% of the torque of using 4 layers in the rotor drum assembly.  This new technology amplifies the torque from four rotor disks rotating through five stator tab stems through each of the toroid coil’s core opening.

The third torque amplification technology is to have the addition of a permanent magnet in each of the toroid coil assemblies where the function of this magnet is to double the flux and torque in the torque active area of the toroid coil when the coil power is on and the flux is rerouted away from the torque active area when the power is turned off.  There are several people, some with patents using similar torque amplification techniques as this second one.

In addition to this, in theory, the motor should operate with about the same input current with changing loads using this new toroid hybrid design. Toroid coils operate with less current than solenoid coils as well.

What is so promising in this new motor design is that it combines all of these torque amplification into one device.  Electromechanical devices have a lot of losses in a system level design where it is hard for them to have a self-running system level free energy system.  But with this new design, all of the amplification of the flux and torque in the system with limited electrical energy to operate the motor, should be able to overcome all of the losses in a system level design.

In addition to that I have energy recovery circuits for the collapsing flux from the core materials.

In addition to this, I have methods to make the power drive circuits more efficient in the motor system.

This motor is an open systems so it does not violate the laws of thermodynamics.

I would like to hear some responses from this forum as to what their thoughts are on this motor?

Lunkster