Author Topic: Kapanadze Cousin - DALLY FREE ENERGY (Read 11870898 times)

tgraca · « **Reply #7740 on:** January 12, 2015, 06:05:28 AM »

Quote from: br549 on January 12, 2015, 02:53:30 AM

I am still experimenting with the same little coil. I added a third winding (L3) I am now running both the
Function Generator and the Scope from the 12VDC to 120VAC inverter to eliminate any influence from other
grounds. I cleaned up the experiment a little (got rid of excess wire) makes it easier to play with. L3 coil
was just a length of wire I had laying around (30 inches #24 awg. I am not making any claims here one
way or the other. Just working through the experiments and showing what I did, and how I measured it.
I am probably out in the weeds with this (it not like I haven't been there before) but I am going to continue
experimenting with this particular coil setup for a little while longer, although not sure where to go next.
The input and output wave forms are the same shape and phase. The probes used to measure input and
output (V & I) are the same. The only thing that changes is the amplitude between the input and output
wave forms. I am thinking that since the wave forms are the same, that the scope is calculating all of them
the same way.
Any constructive feedback encouraged.
Here is my video for the attached circuit.
t http://youtu.be/3KLKAn9jnak
Have a great day:
br549

Dear br549 - suggestion: I have about a dozen ways of checking COP, but my tests always start with this one.
Amps (amp draw) of course are tested in line. You can also test the power going to the inverter from the battery (since it is part of your circuit), which will reduce COP.

NickZ · « **Reply #7741 on:** January 12, 2015, 06:28:59 AM »

quote:
" remember to place caps and many more to create
a balance (resonance) and get high output like how I did, the ones befor the ferrite yoke and befor the yoke."
end quote.
Geo: With my current set up, adding more caps (more than one or two caps) does not help to increase the output, like it did on the RMG.
I'd like to try the IRFP2907 fets, also, to see if they can handle the overheating issue better than the IRFP260N, that I'm using now. They're rated at 75v, 209 watts, and only cost a little more.

skywalker66 · « **Reply #7742 on:** January 12, 2015, 09:26:42 AM »

Quote from: John.K1 on January 11, 2015, 02:38:12 PM

Guys, Ruslan has new videoon YouTube since yesterday https://www.youtube.com/watch?v=xPjELtEEtq4

Generally what he says is - short impulses on antenna (up to 500ns)
On the picture where he shows the magnetic field he says you must give it the impulse not at the top of the amplitude rather a bit on the side.
Next think is the inductor coil has to hold/keep resonance . In overall he says it is resonance in resonance.

Partially I do and partially I do not understood what is he talking about. Can somebody tell me how big is a magnetic field he talks about, around the Tesla coil?? As far as I understand the HV is like a static electricity. The size of magnetic field depends on the current. No current no magnetic field. So how can magnetic field be the main process in this device??? It looks to me more like a big capacitor with the inductor coil in the middle.

BTW: He doesn't want to show any schematics nor sell his device. He says he wants you to understand it and build your own schematics
Thanks

Thanks John !
About impulses on antenna up to 500ns...
A kacer produce a HV sinusoidal shape at top. To get some sort of impulses at top of kacer, it must be half rectified that sinusoidal output. If Ruslan spoke about 500ns impulse, it means a 1us period (or 1MHz) half rectified. Most like Ruslan use a diode between kacer emitter and ground for that purpose.

" Can somebody tell me how big is a magnetic field he talks about, around the Tesla coil??"
No more big than a ordinary kacer. Maybe he talking about magnetic field induced by 2 layer inductor around grenade, I can't tell, I don't understand rusian language.

"It looks to me more like a big capacitor with the inductor coil in the middle. "
Indeed, the antenna and grenade form an asymetric HV capacitor.

skywalker66 · « **Reply #7743 on:** January 12, 2015, 11:21:47 AM »

Quote from: GeoFusion on January 12, 2015, 05:52:13 AM

...
for everyone, Just maybe I will demonstrate a small device I build last year nov. for the test of particle harnassing effect , has Flyback trans and mazilli, caps and uses ground.
The device only works when the ground is connected. or can generate energy , it harnesses energy from ground. and environment.
it's fun but has amazing effects.

Cheerz

Then, please by all means fell free to elaborate about your amazing effects, unless you want to join to Akula&Ruslan club

itsu · « **Reply #7744 on:** January 12, 2015, 02:06:05 PM »

Quote from: br549 on January 12, 2015, 02:53:30 AM

I am still experimenting with the same little coil. I added a third winding (L3) I am now running both the
Function Generator and the Scope from the 12VDC to 120VAC inverter to eliminate any influence from other
grounds. I cleaned up the experiment a little (got rid of excess wire) makes it easier to play with. L3 coil
was just a length of wire I had laying around (30 inches #24 awg. I am not making any claims here one
way or the other. Just working through the experiments and showing what I did, and how I measured it.
I am probably out in the weeds with this (it not like I haven't been there before) but I am going to continue
experimenting with this particular coil setup for a little while longer, although not sure where to go next.
The input and output wave forms are the same shape and phase. The probes used to measure input and
output (V & I) are the same. The only thing that changes is the amplitude between the input and output
wave forms. I am thinking that since the wave forms are the same, that the scope is calculating all of them
the same way.
Any constructive feedback encouraged.
Here is my video for the attached circuit.
t http://youtu.be/3KLKAn9jnak
Have a great day:
br549

Hi br549,

nice clear setup and presentation.

Personally i would never use only 1 lead of a FG or scope and use that data for input/output/cop calculations.

Also i am sure you are aware that flipping over the current probe will show a 180 degr. change in phase, so
you have to be aware you are using the correct direction.

In a LCR circuit like your output circuit, the max phase difference will be + or - 90 degr. (never 180) (anybody correct me if i am wrong)
so i guess you were using the correct direction here showing a slight current leading the voltage (capacitive).

Regards Itsu

br549 · « **Reply #7745 on:** January 12, 2015, 02:31:54 PM »

Quote from: tgraca on January 12, 2015, 06:05:28 AM

Dear br549 - suggestion: I have about a dozen ways of checking COP, but my tests always start with this one.
Amps (amp draw) of course are tested in line. You can also test the power going to the inverter from the battery (since it is part of your circuit), which will reduce COP.

tgraca:
You are right, I understand what you are saying about measuring the input power at the
source, but in this case i was only interested in the coils input and output performance,
thinking that if it seemed promissing, I would work on a low power input circuit to pump
it. Not sure what to think about this yet. May take a little break from it for now, and try to
learn more about coils and magnets.
Have a great day;
br549

br549 · « **Reply #7746 on:** January 12, 2015, 03:08:00 PM »

Quote from: itsu on January 12, 2015, 02:06:05 PM

Hi br549,

nice clear setup and presentation.

Personally i would never use only 1 lead of a FG or scope and use that data for input/output/cop calculations.

Also i am sure you are aware that flipping over the current probe will show a 180 degr. change in phase, so
you have to be aware you are using the correct direction.

In a LCR circuit like your output circuit, the max phase difference will be + or - 90 degr. (never 180) (anybody correct me if i am wrong)
so i guess you were using the correct direction here showing a slight current leading the voltage (capacitive).

Regards Itsu

itsu:
I was trying to simulate an antenna or one wire setup with the FG like the antenna from the
katcher circuit. When I connect the common for the FG and the scope (as normally done), the
current & voltage phase relationship stay the same, and the COP drops to 4. After all the
messing around with this simple little experimental circuit, it becomes more and more clear
why measured DC power in vs DC power out is the prefered method.
Have a great day:
br549

tgraca · « **Reply #7747 on:** January 12, 2015, 03:35:45 PM »

Quote from: br549 on January 12, 2015, 02:31:54 PM

tgraca:
You are right, I understand what you are saying about measuring the input power at the
source, but in this case i was only interested in the coils input and output performance,
thinking that if it seemed promissing, I would work on a low power input circuit to pump
it. Not sure what to think about this yet. May take a little break from it for now, and try to
learn more about coils and magnets.
Have a great day;
br549

I forgot to thank you for posting the video. I love to see experiments on this small level.
It's the way I work too and gives me ideas for my own work. Thanks for sharing. -teo

tgraca · « **Reply #7748 on:** January 12, 2015, 04:01:40 PM »

Quote from: tgraca on January 12, 2015, 03:35:45 PM

I forgot to thank you for posting the video. I love to see experiments on this smaller scale.
It's generally the way I work too and gives me ideas for my own work. Thanks for sharing. -teo

GeoFusion · « **Reply #7749 on:** January 14, 2015, 03:11:54 AM »

Hi guyz

Done uploading the vid,
I promised I would show the device that depends on earth grounding.
Small but has some interesting effects.
It even EMPs my Wifi router completely !! So no internet when it's on. haha

https://www.youtube.com/watch?v=M1SP9nMVWec

And new Vid of Ruslan, This is a good one with His Full Drawn Schematic, Enjoy
https://www.youtube.com/watch?v=1LhF261VDQw

CHeerz~

Ed morbus · « **Reply #7750 on:** January 14, 2015, 07:20:34 AM »

Ruslan video 2

https://www.youtube.com/watch?v=XVKhXfUZefc

Ed morbus · « **Reply #7751 on:** January 14, 2015, 07:28:23 AM »

Ruslan schematic

John.K1 · « **Reply #7752 on:** January 14, 2015, 08:16:17 AM »

Hi Geo,

Thanks for your video and link . I have to smile a bit as I have used yesterday two same home made caps

- In my case I needed two in series to get the inductor coil in to the resonance.
Anyhow, I do some tests - I have my inductor coil as LC tank with one tap on the bulb and than on ground. The bulb 220V 25W lits full brightnes but the consumption is too high (24V @ 3A)
When I use the clamp Amp meter on the ground wire it shows 7.5 A DC . When I connected my Analog meter in line it shows only 30mA.

Next -when I connect diode bridge across the bulb, the output is around 280-240V. I can connect the cap and it charge fine. It charge much faster if I connect only one lead to the bulb and the second lead is free. Ground than on negative side of the diode bridge. Than I was blinking the 220V LED bulb 3x in second.

Hoppy · « **Reply #7753 on:** January 14, 2015, 10:11:12 AM »

Quote from: GeoFusion on January 14, 2015, 03:11:54 AM

Hi guyz

Done uploading the vid,
I promised I would show the device that depends on earth grounding.
Small but has some interesting effects.
It even EMPs my Wifi router completely !! So no internet when it's on. haha

https://www.youtube.com/watch?v=M1SP9nMVWec

And new Vid of Ruslan, This is a good one with His Full Drawn Schematic, Enjoy
https://www.youtube.com/watch?v=1LhF261VDQw

CHeerz~

Hi Geo,

Thanks for showing your video. This is the first video I've seen that shows the Kapanadze type lamp dimming effect after switch-on. I think you are close. Are you using a Mazilli to pulse the flyback coil?

GeoFusion · « **Reply #7754 on:** January 14, 2015, 04:48:45 PM »

Hi there Guyz

John.K1,
haha Awesome man, so you also know they way of salt water capacitor for some hardcore testing

.
Normally use them for my first spark gap Tesla coil, I think I have a vid of it on my channel.
Nice results and interesting. Yes when you rectify the output it has a high lv of voltage DC, but remember, it's radiant.
the reason why measuring it is a bit hard. in anycase you where able to light it up

, now try to connect a TL494 generator to it.
mixing is needed here.
Keep on with the experimenting, Keep a close look how I move too and ruslan.

Hoppy,
Hi man, no probs anytime for learning purposes

. This is to show what I understand up till now about Earth ground
Thnx to what Ruslan is showing and doing, it all makes alot more sense now.
Yes that is a standard Mazilli I used there to pulse the Flyback , also used that particular one for earlier roundcore experiments.
Imagine now putting that in place of the kacher on the ruslan device, when you see the schematic. as example:),
It needs the ground to attract radiant energy particles and depending on your driving force it will harness even more I guess.

and storing it all in caps.

It somehow makes sense now how it should work with Ruslan's device,

I feel we are almost there.
High voltage is necessary to activate the ground line

This is also the new video Ruslan posted and I attached his corrections he drew in his schematic.
https://www.youtube.com/watch?v=XVKhXfUZefc

Cheerz~

News:

User Menu

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY (Read 11870898 times)

tgraca

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

skywalker66

Re: Kapanadze Cousin - DALLY FREE ENERGY

skywalker66

Re: Kapanadze Cousin - DALLY FREE ENERGY

itsu

Re: Kapanadze Cousin - DALLY FREE ENERGY

br549

Re: Kapanadze Cousin - DALLY FREE ENERGY

br549

Re: Kapanadze Cousin - DALLY FREE ENERGY

tgraca

Re: Kapanadze Cousin - DALLY FREE ENERGY

tgraca

Re: Kapanadze Cousin - DALLY FREE ENERGY

GeoFusion

Re: Kapanadze Cousin - DALLY FREE ENERGY

Ed morbus

Re: Kapanadze Cousin - DALLY FREE ENERGY

Ed morbus

Re: Kapanadze Cousin - DALLY FREE ENERGY

John.K1

Re: Kapanadze Cousin - DALLY FREE ENERGY

Hoppy

Re: Kapanadze Cousin - DALLY FREE ENERGY

GeoFusion

Re: Kapanadze Cousin - DALLY FREE ENERGY