TenselKoala, void, jeg, & itsu:
You guys are right. I replaced the LED's with a resistor so all of the waveforms were the same,
measured and calculated the RMS voltage X RMS current (input and output) as I had done previously and the COP came out to be 0.81.
Then I used the math functions as itsu instructed, and the COP came out to be 0.4. There goes my fortune and fame,  although I am going to continue experimenting with this coil configuration for a little longer for better understanding.
Have a great day:
br549

br549,
thank you very much for honestly sharing ur experiments and results. In my opinion ur fame and fortune didnt go away, but just reached new heights... 
I for my part really welcome your research in the area of conductor length and mass ratios 

 Thinking about measuring , not an easy task, especially if ground connections are nessecary for operation and meters, and influence results. Also im asking myself if our known measurement devices and proceedings really tell us truth about whats happening. If there is (standing/longitudinal/whatever) waves making stuff happen in these devices (even including supply leads like described by some), or possibly other anomalous effects occuring at certain points of the conductors, where and how to measure energies IN/OUT at all?
My persoanl aproach here, whenever possible, is to work with rectified and filtered DC at IN and OUT, or try looping, but this might also "kill or shadow effects"... And then, how do i know the DC OUT is from same star like DC IN and can be correctly measured with meters from IN star? 


regards

Ruslan video 2015

https://www.youtube.com/watch?v=bBQtH6HNlvw

Tariel used spark to get nanosecond pulse, Dally like wise used nanosecond pulse ,Russian like wise is using nanosecond pulse.

Nice work! I have not had any success with this thing, but in my inductive reactance experiments and from what I have seen others do
with the Kapanadze, Sweet, and other devices, the larger gauged wire works better because it has less resistance. Sorry if everyone is
already working along these lines, but this is just my thoughts on getting the nanosecond pulse rate - less ohms in the coils.
I reference this page often.

http://en.wikipedia.org/wiki/Electrical_reactance#Inductive_reactance

Again, sorry if this is "old hat" for you guys. Let me know if this thought was useful.

Guys, Ruslan has new videoon YouTube since yesterday  https://www.youtube.com/watch?v=xPjELtEEtq4

Generally what he says is - short impulses on antenna (up to 500ns) 
On the picture where he shows the magnetic field he says you must give it the impulse not at the top of the amplitude rather a bit on the side.
Next think is the inductor coil has to hold/keep resonance . In overall he says it is resonance in resonance.

Partially I do and partially I do not understood what is he talking about. Can somebody tell me how big is a magnetic field he talks about, around the Tesla coil?? As far as I understand the HV is like a static electricity. The size of magnetic field depends on the current. No current no magnetic field. So how can magnetic field be the main process in this device???  It looks to me more like a big capacitor with the inductor coil in the middle. 

BTW: He doesn't want to show any schematics nor sell his device. He says he wants you to understand it and build your own schematics  
Thanks

hi John.K1,

I did saw the nanosecond pulser circuit once more and looks like it's going back to the PWM generator via blue/black wire from nanopulser circuit.
I can't tell if he is modulating nanosecond pulse with pwm generator which may cause the dual output to produce square wave but with many pulse within the square wave ~500ns.

He is hiding this portion very well from the public.

I did sent Ruslan a message in Russian in youtube comment  after sorting the sentence in Russian.But no reply since as usual.

-------------------
ok i have just spotted a comment from Ruslan to someone in youtube which i have translated  which may prove my theory that he is modulating the ~500ns with pwm generator.


{
 Frequency inductor 28-32 kHz, but the pulses whose duration is equal to 1.8-2 MHz and there is need for strikes. Kachernye pulses can be served by one half-period. It's then I'll tell you.

}

Anyway, the task is to hold resonanc on the inductor coil and make sync to Tesla coil to get impulse right behind the top of the amplitude on the inductor's LC contour.  Piece of cake    

BTW- I am thinking to make sharp impulses by using the small discharge tubes. I have some at home and making some experiments  with that right now.

(discharge tubes  :  http://ie.farnell.com/webapp/wcs/stores/servlet/Search?st=discharge&catalogId=15001&categoryId=700000006299&langId=353&storeId=10163"  )

  All well and good, but, we really need a video that will show the turning process. As that's what we can't seem to be able to do properly.
To understand how it all works, we need to make the device and see it work, first. No amount of theory is going to help unless a proper replication is made, using the right tuning methods. As we are all failing at the pulse sycronization level, of the various pulses. And that's what Ruslan or Akula could help us with, if they wanted to. But, do they really want to show us?
   It also seams to me that they may need to have other people demostrating their working free energy devices, (other people's replications), to really prove the point of where the extra energy is coming from.

   Geo: I got my new kacher coil working now, but I still can't seem to tune the device to obtain the needed effect generation.  May have to remove some turns.
    Mosfet are still getting hot. I tried different chokes, but in order to reduces the overheating, the chokes also drop the output power levels.
I haven't found a happy medium, yet.

 

br549,
thank you very much for honestly sharing ur experiments and results. In my opinion ur fame and fortune didnt go away, but just reached new heights... 
I for my part really welcome your research in the area of conductor length and mass ratios 

 Thinking about measuring , not an easy task, especially if ground connections are nessecary for operation and meters, and influence results. Also im asking myself if our known measurement devices and proceedings really tell us truth about whats happening. If there is (standing/longitudinal/whatever) waves making stuff happen in these devices (even including supply leads like described by some), or possibly other anomalous effects occuring at certain points of the conductors, where and how to measure energies IN/OUT at all?
My persoanl aproach here, whenever possible, is to work with rectified and filtered DC at IN and OUT, or try looping, but this might also "kill or shadow effects"... And then, how do i know the DC OUT is from same star like DC IN and can be correctly measured with meters from IN star? 


regards

I am still experimenting with the same little coil. I added a third winding (L3) I am now running both the
Function Generator and the Scope from the 12VDC to 120VAC inverter to eliminate any influence from other
grounds. I cleaned up the experiment a little (got rid of excess wire) makes it easier to play with. L3 coil
was just a length of wire I had laying around (30 inches #24 awg. I am not making any claims here one
way or the other. Just working through the experiments and showing what I did, and how I measured it.
I am probably out in the weeds with this (it not like I haven't been there before) but I am going to continue
experimenting with this particular coil setup for a little while longer, although not sure where to go next.
The input and output wave forms are the same shape and phase. The probes used to measure input and
output (V & I) are the same. The only thing that changes is the amplitude between the input and output
wave forms. I am thinking that since the wave forms are the same, that the scope is calculating all of them
the same way.
Any constructive feedback encouraged.
Here is my video for the attached circuit.
t http://youtu.be/3KLKAn9jnak
Have a great day:
br549

  All well and good, but, we really need a video that will show the turning process. As that's what we can't seem to be able to do properly.
To understand how it all works, we need to make the device and see it work, first. No amount of theory is going to help unless a proper replication is made, using the right tuning methods. As we are all failing at the pulse sycronization level, of the various pulses. And that's what Ruslan or Akula could help us with, if they wanted to. But, do they really want to show us?
   It also seams to me that they may need to have other people demostrating their working free energy devices, (other people's replications), to really prove the point of where the extra energy is coming from.

   Geo: I got my new kacher coil working now, but I still can't seem to tune the device to obtain the needed effect generation.  May have to remove some turns.
    Mosfet are still getting hot. I tried different chokes, but in order to reduces the overheating, the chokes also drop the output power levels.
I haven't found a happy medium, yet.

 

Hi Nick,

Nice man got the kacher working now . keep on experimenting, it's the only way we all can figure it all out.
sad that the mosfets are getting hot like that and yes the chokes play a big role but remember to place caps and many more to create
a balance (resonance)  and get high output like how I did, the ones befor the ferrite yoke and befor the yoke.
you'll reach.

yes the tuning and synchronization part is a very important when finalizing and part beginning of Ruslan device.
part of reaching resonance. Up till now what I understand what Ruslan is telling  is that
there is  a Resonance Within a resonance happening.

up till now, that I'm able to replicate there High speed Mosfet drivers to test, this will determine everything.
almost done with it, just needs some more soldering and done for the test.
You will need a TL494 circuit to continue this work, will give the effect needed.
yet saw many other replications, but some ppl are missing out how to connect everything, especially the ground sometimes
 but I will do as I see on the schemaz.
and to experiment with the circuit on my own.

 for everyone, Just maybe I will demonstrate a small device I build last year nov. for the test of particle harnassing effect , has Flyback trans and mazilli, caps and uses ground.
The device only works when the ground is connected. or can generate energy , it harnesses energy from ground. and environment.
it's fun but has amazing effects.

Cheerz