But no Scoop here at home, only use scoop at a friend's. but could check it out.
Cheerz~

Sorry; I just have to say something just once

scoop = scope
sins = since

'the sins of the father are visited on the son.'
'it's been a while since it has rained'

'take a scoop of flour.'
"they'd scoped out their market"  assess or investigate (something).

hi zcsaba77,

The online web "L/C formula" applies for ferrite or Air core inductor or other types of core.

My explanation is simple just solve the power for the primary coil first without creating the secondary coil yet.

If primary coil test failed and produced no heating effect for verifying "the strength of alternating magnetic field"  then please "do not proceed" with secondary coil which will only confuse you further.

Hi MagPWR

Maybe I look stupid, but you can me write down process?
If I have yoke core, make wind on core, wind to core softly, make it movable core, take core away from coil for hot testing, or how?
Because if I make coil for induction test, this wont work as well with core, probably will change induction, capacitance, frequency and etc.

regards zcsaba77

Check this out, this will help too.
Experiment guyz try these out. Only when you try you will find out why

GF thanks for all this! Is the attached schematic the whole generator circuit? Doesn't need to introduce the high frequency component on the peaks of this high current sinus? Also the question is for your schematic. Doesn't need a higher frequency superposition?
Thanks again for what you are trying to do!

Jeg

Hi Guyz 

Something for you guyz to read, About Ruslan. Important
http://peswiki.com/index.php/OS:Russian_replications_of_Kapanadze_solid_state_circuit

Srry for the Typo's d3x0r. Guessing was using to much Dutch lately, makes me type differently my apologies.


  Void:
yes at the bottom you have the square wave driver circuit as you can see .
Yes, one step up there too, to get 24Vdc, but the circuit can be build such a way that you could supply the MosFets and IGBT's of certain rating with 120Vdc or 220Vdc + ! Akula did use 300Vdc on his first Sqaur wave circuit with IGBTs.
I can some how share some Tesla coil schematics I used  but the bottom circuit can be used also to operate an  Solid State Tesla Coil.
The top part is Kacher Circuit, Tesla coil. it is a oscillator. Do not fully understand  why it's being used but I see that It amplifies the output and must somehow effect the other squar pulse field in such a way. works as a Disruptor
 Yes , this circuit I used completely. but did minor mods on the output winding, it's all experimental.


   Nick:
yes, somehow a scope is needed, but it will eventually come. I could sometime borrow one from a friend, but fragile instrument.
Saw your pic of the coiling ,
Your Kacher tesla coil looks good but you will need to change the Primary thick coil with a smaller gauge wire.
and the output where induction is happening pulsed, you will need so see how many winds you'll need for your desired output voltage and amps. Your white and red coils I see there should be good gauge I guess.
Thick wire gauges  do play a important role for output amps at the output coil. take good look at akula videos.

Btw the yoke core's primary (white wire) is wrongly turned in the pic posted.
It's the same way how I've shown befor with the roundcore, it's only one direction and with center tap.
even the Mazilli circuit you re-posted you see where the 6 + 6 winds are at the flyback are one direction and center tap. that is how it should be wound for the yoke.
yes electrical tape or paper are in between the two halfs.

 
   Jeg:
No problem man . this is the whole Generator circuit. But anyone can modify it, but It will be harder to Tune if you do.
The circuitry produces the High frequency and squar wave pulses for  the system to operate.
If you build it as you see on the schematic you will see.


Cheerz~

 Ruslan generator new clip…
 
https://www.youtube.com/watch?v=tT9m6F53atk
 
 
schematic of  the coil…from  russian forum
 
http://www.realstrannik.ru/forum/39-kapanadze/134930-ustanovka-ruslana-kulabuxova.html?start=342
 
 
 
from youtube “leader jane” channel  who is making the Rusaln coil also..
 
https://www.youtube.com/watch?v=anvb_PXG1YA
 
 
https://www.youtube.com/watch?v=yKjgMmZcFA0


and Thanks  !!!     "Geo"


Acca...

  Geo:
   Ok I'll put a thinner gauge primary wire on the Exciter, I'm still adding more coil turns on the induction heater side, and testing it now. I want to see just what the thicker red wire does on the Exciter first. As I've used this exciter's output coil before, I know what to expect from it. But, I want to use the thicker wire to see what it does. As I feel that even flattend copper tube, would work best. Or not?

  I just found my 3 inch ferrite rod, to make the HV choke with, that was what I needed to continue, for joining the two separate coils sides together.

  I think that in time we'll find a way to just buy both the induction crt board, as well as the HV nano pulcer crt board, commercially made.
  But, having the exact coils specs, helps. I made the yoke primary all in the same direction. The picture was taken previous to that change. But, I see no difference, in the output readings, one way or the other. Nor with the yoke clips on, or off.
I am still using the tape between the yoke core halves.
   Thanks for the tips.

http://youtu.be/F7kOKI7QLVw




Wesley