Author Topic: Kapanadze Cousin - DALLY FREE ENERGY (Read 11891761 times)

AlienGrey · « **Reply #14610 on:** August 12, 2016, 01:41:09 AM »

Have a look at this little gem then !

https://www.youtube.com/watch?v=vDp7bH0G7XA

apecore · « **Reply #14611 on:** August 12, 2016, 09:20:49 AM »

Quote from: AlienGrey on August 12, 2016, 01:41:09 AM

Have a look at this little gem then !

https://www.youtube.com/watch?v=vDp7bH0G7XA

AG,

It seems the Don Smith device is working.
Oef......again a new project on the bench.

MenofFather · « **Reply #14612 on:** August 12, 2016, 10:28:40 AM »

Quote from: apecore on August 10, 2016, 08:41:07 PM

NickZ,
Thanks for thelink to Itsu's video,...i just purchased my missing components to build the yoke driver.
It is indeed as menofather says the Topruslan 7 version as wich i now wil replicate.
I attached it,.....i guess your setup is also based on this version?

Question about the yoke:
You mentioned using electric tape on the yoke half,......does the yoke has to be broken in two parts?

Also not clear for me is the torroid dimensions..(you mentioned minimum 3 inch),... i purchased a 102-65-25 torroid, this must be good enough?
The other thing is that i will use for the secondairy 6mm2 stranded wire instead of the mentioned (in the shematic attached) 4mm2.
I hope this won't be a mayor deviation?

These purchased components will arrive tomorrow or the day after tomorrow,.. so then i can start winding the yoke and see if the system stays in resonance when yoke connected ,.........and hopefully i can lite some bulbs as you already showed.
I d like to see if both devices are acting rather the same?
That will be my first next step.

Related to the shematic from MenoFather, i also purchased that components.
Just like to see whats happen driving the tesla in that state, related to the bulb test.
So MenoFather thanks for the information,.... i wil come back on that

Another thing i have some questions about the choke wich is used in the main output,.....can someone clearify on that?
For the expected output it should handle about 10Amps i guess?
Perhaps it can be homemade?

it inductance 100 microhenries.

NickZ · « **Reply #14613 on:** August 12, 2016, 08:23:50 PM »

Actually the posted schematic TopRuslan 7 is the one that I'm going to be replicating. Once I can get all the push-pull components. That posted schematic (below) does use the same Kacher circuit that I'm currently using, also.
The TL494 board can be bought ready made for $8, or so. MUR1560 bridge rectifier board can also be purchased ready made for about the same price. Itsu suggested using the Ucc37322 chip for the mosfet driver. So, that is the one I'll be getting, if I can find it.

apecore · « **Reply #14614 on:** August 12, 2016, 10:37:53 PM »

Quote from: NickZ on August 12, 2016, 08:23:50 PM

Actually the posted schematic TopRuslan 7 is the one that I'm going to be replicating. Once I can get all the push-pull components. That posted schematic (below) does use the same Kacher circuit that I'm currently using, also.
The TL494 board can be bought ready made for $8, or so. MUR1560 bridge rectifier board can also be purchased ready made for about the same price. Itsu suggested using the Ucc37322 chip for the mosfet driver. So, that is the one I'll be getting, if I can find it.

Ha Nick,

Good to hear that you build it yourself too.
We will have to indentical replications,... this has some advantage while testeing etc.
I have recieved my 80% components whitin a day,.... so i already make the TL494 circuit.
I ordered at Farnell but discovered that TME is even 50% cheaper on a lot of components f.i. the IRFP260M costs 3,44 EURO at Farnell and 1,41 EURO at TME.
Just to consider.

Tomorrow the other parts ae coming,.... kooling and stranded wire push-pull part etc.
I use the originally chip TC4420 chip for driving the mosfets.

Itsu refers to next link,... here he tests his yoke driver with a lossless clamp setup,... considering his work i think it is the best to use that setup.
No snubbers circuits etc needed.
http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg475512/#msg475512

So i will replicate Itsu's driver setup also the way he soldered the drivers at the mosfets. It is good to see in the video how he did it.
Attached some pictures as you can see how it is made.

Further some changes i ve made;

I changed the tesla coil because in the shematic 0.8mm wire is used,... mine was 0.5mm and i have now used 1.0mm wire, 50mm pipe and 185 turns.
The choke is approx 100uH and is made by 36 turns in 3 layers on a 80mm pvc pipe (wire solid 2.5mm2)..... no core used... (not yet)
Caps for the load are 3 times 3uF/1000V film capacitors

The yoke (because the stranded wire not yet available) i wound it with stranded 4mm2 28 turns and als the 3 windings (there are 4 i see now) also solid 4mm2.
I hooked it al up as shown in the shematic but no bulb activity yet as you shown lately.
Maybe (but i think not) the reason is that my inductor is 9.4m instead of the 18,75?.... i will make a 18,75 version to.....

Now i use as power supply to car batteries,....two 100Ah,...... so lots of testing can be done before charging.

Some other issue,..... i am thinking about;
You mentioned that the tesla coil as to be as close to the output coil as possible...... a reason why could be thath the generated magnetic field coming out of the top has to be absorbed by the left part of the output coil. So this could also be a tuning parameter?
This al has to be optimal before starting the inductor part i guess.

apecore · « **Reply #14615 on:** August 12, 2016, 10:44:24 PM »

Quote from: AlienGrey on August 12, 2016, 01:41:09 AM

Have a look at this little gem then !

https://www.youtube.com/watch?v=vDp7bH0G7XA

AG,

Do you know if there is someone who also wants to replicate this device? Or is there somwhere a forum active?
It is quit clear in the video how al is connected etc.
Only the black ring what is lying on the neon transformer is something i don't reconize?... It look like a ferrite ring?

Thank you in advance

NickZ · « **Reply #14616 on:** August 13, 2016, 12:32:33 AM »

There is an ongoing thread at Energetic Forum where they are replicating some versions of the Don Smith devices.
But, the DS replication in that last post that AG linked to is rather old. Not sure if the flickering lights, were OU, or not. Or if could self run.
Here: http://www.energeticforum.com/renewable-energy/20533-reproducing-don-smith-effect-2.html

apecore: You should try to obtain the Tv yoke, not a toroid core. Tv repair shops may still have some around, or buy an old junk tv and take the yoke out yourself, like I've done. The yokes were made for running at about 15kHz, or so. And are bigger than that toroid you are using.
The yoke cores that I use are 85mm wide, by 45mm tall, or even a little bigger.
Just connect a regular 25w incandescent bulb to the grenade output coil, without anything else connected, and see what you can get at the bulb(s), from just the Kacher's output.
If I disconnect the yoke coil (the cap and 3 turns coil) to the inductor, while the Kacher is running, the bulb brightness decreases at the grenade's output bulb, but, it is there still at about 80% brightness, left even without the inductor working.
So, I think that my tuning is not so bad, and may just need some minor adjustments to reach resonance.
I have seen the amplification effect several times now.

Thanks for the pics, and good luck with your push-pull driver.
I am ordering more components tomorrow

AlienGrey · « **Reply #14617 on:** August 13, 2016, 02:40:41 PM »

Quote from: apecore on August 12, 2016, 10:44:24 PM

AG,

Do you know if there is someone who also wants to replicate this device? Or is there somwhere a forum active?
It is quit clear in the video how al is connected etc.
Only the black ring what is lying on the neon transformer is something i don't reconize?... It look like a ferrite ring?

Thank you in advance

If you look closer at the core former winding I think you might find it has an inner winding my guess it would be tuned to the full wave or it could be split in too ie 1/2 CW the other 1/2 CCW and the there is the circuit to drive it, but who knows ?

apecore · « **Reply #14618 on:** August 13, 2016, 10:52:47 PM »

Quote from: AlienGrey on August 13, 2016, 02:40:41 PM

If you look closer at the core former winding I think you might find it has an inner winding my guess it would be tuned to the full wave or it could be split in too ie 1/2 CW the other 1/2 CCW and the there is the circuit to drive it, but who knows ?

AG
I think it is similar to the DS setup..
Inmer coil 1/4 coil length and secundair cw and ccw...but could even be 1/2
Difference is that the single bulbs are connected.....perhaps used as LC load ....(this is new relatedto the conventional DS setup).
There are more capacitive adjustmenrs also in place.
1/4 or 1/2 wave is something to experinent with..
AG.....you don't know where to find more info to get?

verpies · « **Reply #14619 on:** August 15, 2016, 12:53:04 PM »

Quote from: apecore on August 12, 2016, 10:37:53 PM

I ordered at Farnell but discovered that TME is even 50% cheaper on a lot of components

Don't forget to check http://rs-components.com

NickZ · « **Reply #14620 on:** August 15, 2016, 04:06:16 PM »

In trying something different, I placed an air core wound with some turns of wire and placed it next to the grenade antenna coil. And I got over 1000v on it with no load. So, then I connected it up to a full bridge rectifier, and back to the Kacher's input. The bulb on the grenade brightened up. The rectifier diodes stayed cool.
It seams to behave something like the Vasmus devices mode of operation. And, it seems to have little to no effect on the grenade coil, as far a draining or reducing it's output, as the bulb at the grenade's output brightens up instead. Something to play with, maybe.
I'm still trying to figure out how Poma (Roma) does what he does, also. Using just the Kacher circuit as an input source.

apecore · « **Reply #14621 on:** August 15, 2016, 11:10:51 PM »

Quote from: NickZ on August 15, 2016, 04:06:16 PM

In trying something different, I placed an air core wound with some turns of wire and placed it next to the grenade antenna coil. And I got over 1000v on it with no load. So, then I connected it up to a full bridge rectifier, and back to the Kacher's input. The bulb on the grenade brightened up. The rectifier diodes stayed cool.
It seams to behave something like the Vasmus devices mode of operation. And, it seems to have little to no effect on the grenade coil, as far a draining or reducing it's output, as the bulb at the grenade's output brightens up instead. Something to play with, maybe.
I'm still trying to figure out how Poma (Roma) does what he does, also. Using just the Kacher circuit as an input source.

Nick,
its good to hear you are trying all kinds of things. Out of the box thinking could give some unexpected results,... wich will bring us futher and futher.
I have at this moment one bright bulb of 25W wich is directly connected to the grenade,.. see picture......only ground is also connected to the grenade (otherway around as shown in the shematic)
I will try your last setup,.... how many turns did you make the aircoil?
I tryed to place a simular coil as the antenna right next the antenna coil.....it gave me after rectifying 50V,...small current was going back to the battery (powersupply kacher)
But i saw no gaining in brightness.
I have to go back and get the Vasmus more focussed,.... see what more there is to play

Status Yoke,..
As we speak i am finishing the yoke drivers, so i hope i can test driving the inductor tomorrow.

MF,
I have also finished building the braker tesla schemetac from MF,...i guess the pulsation during "ON" stratus has to be in the resonance frequenty of the tesla coil?
I think the TL914 circuit cannot reach the 1.25Mhz so i must find a way to let the kacher start en stop as it resonate on itself.
Do you have a link where i can follow the Russian forum?

NickZ · « **Reply #14622 on:** August 16, 2016, 04:16:08 PM »

apecore:
Your system is looking better and better. Thanks for turning your coils around, also.
It's good that you got the 25w bulb running brightly. Try two, or three bulbs on as well, to see to what extent they will light. That will indicate just how strong the Kacher's output is.
The long Kacher secondary coil will probably not resonate at 1.2mHz, unless you shorten it. As the higher the running frequency, the shorter the secondary has to be. But you might be able to find a suitable harmonic frequency that will work, like possibly at 600kHz, or so.
I connect the Kacher circuit transistor negative rail to my outside Earth ground. As well as the end of the grenade output coil, so both are connected to the same ground. If you don't connect the grenade to the Earth ground, there will be HV running throughout the whole system, and burning out all the delicate control circuits. So, please remember to ALWAYS use the earth ground, which should also be the same size as the grenade output coil 37.5, or so.
Several of us have disregarded that advice, and have paid the price.
The stronger that the HV signal is, the more harm it can do to the yoke's circuit delicate control components, if not earth grounded. Although it looks like you're very quick and proficient at assembling the drivers, watch out with the HV impulses.

The extra coil that I had used next to the antenna, was a 40 turn magnet wire air coil, wound on 1 1/4 inch pvc pipe, with some ferrite in the former pipe, which also seams to help. I just had this coil laying around. I would think that 50 turns would be better. Once rectified the voltage does drop to about 20v, or so, but that can be adjusted by adding or removing turns on the coil to get the best running voltage. A filter cap after the rectifier is also needed. The Kacher transistor temps will also increase, so watch out for that if you try it.

AlienGrey · « **Reply #14623 on:** August 16, 2016, 04:39:52 PM »

Quote from: NickZ on August 16, 2016, 04:16:08 PM

apecore:
Your system is looking better and better. Thanks for turning your coils around, also.
It's good that you got the 25w bulb running brightly. Try two, or three bulbs on as well, to see to what extent they will light. That will indicate just how strong the Kacher's output is.
The long Kacher secondary coil will probably not resonate at 1.2mHz, unless you shorten it. As the higher the running frequency, the shorter the secondary has to be. But you might be able to find a suitable harmonic frequency that will work, like possibly at 600kHz, or so.
I connect the Kacher circuit transistor negative rail to my outside Earth ground. As well as the end of the grenade output coil, so both are connected to the same ground. If you don't connect the grenade to the Earth ground, there will be HV running throughout the whole system, and burning out all the delicate control circuits. So, please remember to ALWAYS use the earth ground, which should also be the same size as the grenade output coil 37.5, or so.
Several of us have disregarded that advice, and have paid the price.
The stronger that the HV signal is, the more harm it can do to the yoke's circuit delicate control components, if not earth grounded. Although it looks like you're very quick and proficient at assembling the drivers, watch out with the HV impulses.

The extra coil that I had used next to the antenna, was a 40 turn magnet wire air coil, wound on 1 1/4 inch pvc pipe, with some ferrite in the former pipe, which also seems to help. I just had this coil laying around. I would think that 50 turns would be better. Once rectified the voltage does drop to about 20v, or so, but that can be adjusted by adding or removing turns on the coil to get the best running voltage. A filter cap after the rectifier is also needed. The Kacher transistor temps will also increase, so watch out for that if you try it.

If you think the Katcher winding is too long have a look at Geo's device his looks full wave to me..
ask yourself this question is a 1/4 wave half the frequency, a 1/4 of the frequency or double the frequency or four times the frequency ? in this database you will find an interpreted article all about this phenomena and how it works.
AG

apecore · « **Reply #14624 on:** August 16, 2016, 05:16:12 PM »

Quote from: AlienGrey on August 16, 2016, 04:39:52 PM

If you think the Katcher winding is too long have a look at Geo's device his looks full wave to me..
ask yourself this question is a 1/4 wave half the frequency, a 1/4 of the frequency or double the frequency or four times the frequency ? in this database you will find an interpreted article all about this phenomena and how it works.
AG

AG,

Do you have a link to the mentioned info from GEO?

Thanks in advanche

News:

User Menu

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY (Read 11891761 times)

AlienGrey

Re: Kapanadze Cousin - DALLY FREE ENERGY

apecore

Re: Kapanadze Cousin - DALLY FREE ENERGY

MenofFather

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

apecore

Re: Kapanadze Cousin - DALLY FREE ENERGY

apecore

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

AlienGrey

Re: Kapanadze Cousin - DALLY FREE ENERGY

apecore

Re: Kapanadze Cousin - DALLY FREE ENERGY

verpies

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

apecore

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

AlienGrey

Re: Kapanadze Cousin - DALLY FREE ENERGY

apecore

Re: Kapanadze Cousin - DALLY FREE ENERGY