Hello Itsu,

I review the question which this post started about the 90deg phase shift. The answer to your question has been already seen by your eyes. The Tesla Electrical Transformer was design by our forefather Nikola Tesla to do exactly what you always question. I think you have already read one of the patent of Nikola Tesla with two separated wound induction coils, the first design he come up for the low frequency alternating current-something like Improvement for Induction Transformer on which works  the same with hes very amazing principle of Rotating Magnetic Field of Nikola Tesla.

I  think you will not go anywhere when you always follow these fame big guys who like to show misleading coil configuration. I had long ago take forgotten to follow these fame free energy guys, when I realized that all of there findings always point to one man, NIKOLA TESLA. 

What we did is forget these fame guys, and work with this detailed paper which we called patent of Nikola Tesla. We tried for first time the picture which I always post on any related Kapanadze device. We have found and observe with our own eyes that what we are looking is not simple Magnetic Induction, when we accidentally left the suppose to be adjustable Bifilar winding left hanging free with no connection, then connected a bulb on one of its end, the other termninal of the bulb is connected to the ground.  I think  everyone here have seen with there own eyes that the HV discharge of a Tesla Coil like to flow to a zero potential difference which is  Ground Earth..

The same picture which I always post here about this Electrical Transformer which shows promising result, We tried to short circuit or close loop all extra winding of any coil left, but still the bulb shines with a blinding brightness with no decrease of its light.

The we tried to connect any capacity or capacitor available, any capacitor connected the same way with the bulb can be charge easily and eventually will make a spark within its terminal.

What do you exactly on this Tesla Electrical Transformer? If you only look this transformer as a mere coil then you will not succeed on this journey. 

These Tesla Electrical Transformer is a coil when you look at it, but when on operation they are Two Joint Capacitor working in a Resonance bouncing of its energy while at the same time amplifying its energy thru conduction of the Ground Points. Because these two electrical transformer also works as Auto Transformer on operation..



Meow.

Thanks stupify12,

i can follow that, but these "Capacitor/or any form of Capacity(Coil)" values are fixed, they should not change when activating the Kacher.
So the question really is why do we see a 90° phase shift when activating the Kacher?

Regards Itsu

Just wonder why nobody is/was able to copy Vasmus work.  It is around an half year ago I have seen something what was looking same as Vasmus device (it probably was that device). if I good remember, there was some device similar to a toroid transformer. But the main think is, there was used Permalloy foil.
I just stopped to trust all this " Copperfields" and started to put my brain and hands to it. If we will just follow "Monkey see monkey do" path we will get nowhere.

  John:
   The reason that nobody has even tried to replicate the Vasmus device is mainly due to him providing no diagram (up to now). Or a full explanation of what is really going on. I suspect that he will follow up on that, and actually explain more fully how to make it work.
  Most guys that have self runners are still worried as to the consequences of making it public. Or at least, before they cash in on the profits from it.

  Even GeoFusion, never showed his supposed self runner. So, it looks like Hoppy may have been right, and he never showed it because he does not have it working. This is not good, and it is better not to mention it, than to mention it and not show it.  So, I'm still waiting to see his current version, but no video, no pics,  nothing, yet.

  EDIT:  I'm also wondering why any battery is needed to just start the device.
As a cap can be charged from the output, with an on/off switch that will allow it to hold it's charge when the device is turned off, without draining this start capacitor, until needed to start the device working.  Too simple?

Ok guys on the relays being used in conjunction with the power switch.
For these simple demo devices I think a simple heavy duty power switch should 
work fine however for the same purpose. Seems like unnecessary circuit complication to me.

Hoppy: Yes, 9V could be used to latch a latching relay connected to a hidden battery, but no actual
evidence of such a battery so far.

All the best...

Ok guys on the relays being used in conjunction with the power switch.
For these simple demo devices I think a simple heavy duty power switch should 
work fine however for the same purpose. Seems like unnecessary circuit complication to me.

Hoppy: Yes, 9V could be used to latch a latching relay connected to a hidden battery, but no actual
evidence of such a battery so far.

All the best...

Yes, on the surface of it, an unnecessary circuit complication given that the switches are heavy duty mains rated and more than suitable for switching low voltage, high currents!

Granted that there is no evidence of battery but exactly what is under all that foam packing. It takes only a small Lion or Lipo flat pack to run a couple of low wattage lamps for the few minutes shown in the video.  In my book, a guy that removes a small piece of foam in one box but fails to show what's under the large pieces in the other box, is just shouting out that he is hiding important components.

  Also makes me wonder why any foam is needed at all. As this a demonstration, not meant to be taken camping. At least not yet.  Not that this is what I think is happening.

Hi Nick. The first thing that caught my eye when Ruslan opened the boxes was
the foam packed around the heatsinks. Foam is a thermal insulator and will hold
the heat in the heatsinks and hinder their ability to dissipate heat. Heatsinks need
air space around them and decent air flow to work well. Take this in conjunction with
Ruslan's very strange diode and capacitor arrangement in the box on the left hand side
and it does look suspicious. If I had heat sinks in a box for a PWM inverter driver, I would certainly
not pack foam around the heat sinks, and I would also probably drill some holes in the box for air flow. 
I still am not jumping to any conclusions, but it is looking kind of  suspicious. Regarding the foam, Ruslan may just
not have had much experience installing heat producing circuits in boxes. He seems to have improved in that
regard in later devices anyway.

Edit:

  Even GeoFusion, never showed his supposed self runner. So, it looks like Hoppy may have been right, and he never showed it because he does not have it working. This is not good, and it is better not to mention it, than to mention it and not show it.  So, I'm still waiting to see his current version, but no video, no pics,  nothing, yet.
  EDIT:  I'm also wondering why any battery is needed to just start the device.
As a cap can be charged from the output, with an on/off switch that will allow it to hold it's charge when the device is turned off, without draining this start capacitor, until needed to start the device working.  Too simple?

GeoFusion doesn't likely at all have a self running Akula/Ruslan type device. If he did he would have been
able to explain how to tune these devices to get them working. Any info Geo has provided
is info that Akula and Ruslan have already stated previously, or info that is already being discussed
in the forums. He has provided no new insight into these devices.  Geo has never offered any info in regards
to getting these devices working that has helped anyone to move forward towards getting their device working.
He seems to be waiting for Ruslan to explain how to do it so he can then put one together himself.
Sorry Geo, but this is the reality of the situation.

Regarding the battery versus cap, a cap can provide a short burst of power, but if it takes
a while for the circuit to sometimes get going as it sometimes seems to, then an ordinary cap
may not have enough juice. Also caps tend to discharge slowly after the power is switched off
due to leakage resistance. There is nothing wrong with using a battery to start the circuit, as
once you disconnect it and remove it, it gets the point across that the starting power is completely
removed from the circuit.

All the best...

Guys, little of theory.  It took me around an hour to translate it for you, so take a peek at least