Author Topic: Kapanadze Cousin - DALLY FREE ENERGY (Read 11867017 times)

NickZ · « **Reply #18150 on:** September 30, 2017, 06:46:43 PM »

"The effect seen here is, magnetostriction causes the core to expand. It expands uniformly, which can be seen as a superposition of many acoustic resonances propagating in both directions (clockwise and anti- around the ring). Intuitively, I don't see that this should cause a problem -- but, if there happens to be just enough nonuniformity to prefer a standing wave, it will develop as the difference between the others. Possibly there could be a feedback mechanism where the motion of resonance affects the strain of the effect, I don't know."
end quote.

Hoppy: Interesting deduction...

You had asked me for a scope shot of my gate signals, so, here's one (BELOW) taken on my new scope.
The TL494 circuit is working fine now along with the tiny 4420 fet drivers. It's something with the yoke that has things heating up, I guess. So, that's where I'm hung up at the moment.
In any case, I'll make another video soon.

Hoppy · « **Reply #18151 on:** September 30, 2017, 07:11:07 PM »

It could be that although the effect of the Kacher is not strong enough to show any appreciable illumination of the bulb, it may be enough to shift the B/H curve of the ferrite enough to show control of the bulbs illumination when the push-pull is running (whilst in RM mode) when using Geo's new Kacher control board, that has both frequency and pulse width control. There may also be hetrodyneing involved.

PS. Thanks for showing your gate waveforms which look fine. Are you limiting the current draw from your PSU?

NickZ · « **Reply #18152 on:** September 30, 2017, 07:56:28 PM »

My Kacher does show an increase in bulb brightness, and heterodyning effects, even in the non RM mode.
But, as my Kacher will light a 50 to 100w bulb by itself, I have to take that into consideration, also. And not allow that gain to fool me at lower loads. However, using 200w or higher loadings, I see little effect from the Kacher. Unlike what Geo was showing previously. I get lots of bright output at lower loads, even without the Kacher. And can even make the yoke ring, but only with the Kacher on, do I get the RM signal, that can change tones with hand movements, etz... However, I don't see that effect when using higher (200w plus) loads, as yet.
And, just where to place the earth ground connections, (I use two), can also affect things, also.

I can get a great looking clean square wave signal at my drains, but there's no magic using a clean square wave signal.
There needs SOME ringing going on, instead. Also an equal sharing of the wasted heat between the fets, RC snubbers, and the Oleg snubber resistors. So, it's a tricky balance to get it all just right. It does take much time, most people would just give it up. But, not me...

Hoppy · « **Reply #18153 on:** September 30, 2017, 08:05:42 PM »

Quote from: NickZ on September 30, 2017, 07:56:28 PM

.... And can make the even make the yoke ring, but only with the Kacher on do I get the RM signal, that can change with hand movements, etz...

That would be consistent with heterodyning.

NickZ · « **Reply #18154 on:** September 30, 2017, 08:34:08 PM »

I corrected that last post of mine, so that it reads right.

Funny thing, here I'm working on my rig, and it's running at around 15KHz, or so. And my daughter comes into the room and from across the room she says, oh, that awful noise, again. But, I hear nothing, even though I'm right next to it. Getting old, I guess.
Sometimes getting old has it's benefits, like not hearing the awful ringing noise, "like the sound that old Tv's use to give off", she says.
Or, from the ghost channel. Radio Moscow

Hoppy · « **Reply #18155 on:** September 30, 2017, 08:46:26 PM »

Quote from: NickZ on September 30, 2017, 08:34:08 PM

Funny thing, here I'm working on my rig, and it's running at around 15KHz, or so. And my daughter comes into the room and from across the room she says, oh, that awful noise, again. But, I hear nothing, even though I'm right next to it. Getting old, I guess.

I have ultrasonic dog/fox scarers in my garden and cannot hear them with my old git ears. However, it drives my son mad when he walks past them.

itsu · « **Reply #18156 on:** September 30, 2017, 09:05:52 PM »

Quote from: stivep on September 27, 2017, 01:57:38 AM

https://www.youtube.com/watch?v=b0hot_kHxN4

Wesley

Wesley,

thanks for the video and translation, but the presented winding direction on the drawn diagram of his Grenade does not make sense.

It only makes sense when flipping over the coil but this should NOT be done, it should be looked at from ONE direction only.

When you do that (looking from ONE direction only), you will see that the L1 / L2 pair of coils do NOT change from CW to CCW, they stay CCW.

Same with the L3 / L4 coil pair, they stay CW.

The ONLY difference with the old style Ruslan Grenade is the last layer layer 6 which is reversed (CCW!!) from its coil pair partner L5 (CW), see
picture below.

So we have:
L1 CCW
L2 CCW
L3 CW
L4 CW
L5 CW
L6 CCW!!

Right?

Regards Itsu

AlienGrey · « **Reply #18157 on:** October 01, 2017, 12:37:49 AM »

Quote from: itsu on September 30, 2017, 09:05:52 PM

Wesley,

thanks for the video and translation, but the presented winding direction on the drawn diagram of his Grenade does not make sense.

It only makes sense when flipping over the coil but this should NOT be done, it should be looked at from ONE direction only.

When you do that (looking from ONE direction only), you will see that the L1 / L2 pair of coils do NOT change from CW to CCW, they stay CCW.

Same with the L3 / L4 coil pair, they stay CW.

The ONLY difference with the old style Ruslan Grenade is the last layer layer 6 which is reversed (CCW!!) from its coil pair partner L5 (CW), see
picture below.

So we have:
L1 CCW
L2 CCW
L3 CW
L4 CW
L5 CW
L6 CCW!!

Right?

Regards Itsu

Hi Itsu I don't see any where, where it gives the wire length or the turns per layer, in order find the wave length he is using. I had a quick scan through a good many of the videos and one where he powers it up it had an annoying blink rate

Void · « **Reply #18158 on:** October 01, 2017, 12:37:50 AM »

Hi Itsu. That guy's explanation of his grenade winding direction was pretty poor,
but from what I could see in the video the only difference from Ruslan's way of doing it
is layer 6 is wound in the opposite direction to layer 5, rather than both layer 5 and 6 being
wound in the same direction.
All the best...

ramset · « **Reply #18159 on:** October 01, 2017, 02:11:13 AM »

Nick Z
quote
Stalker also has a couple of new videos out
end quote

I asked around [members here] and can't find his Channel, nor can i remember it .

can you [Or anyone} post it here or PM me a link [and I'll post it here.

you would be amazed at the you tube links which pop up when you search
Stalker ...

with gratitude

Chet

d3x0r · « **Reply #18160 on:** October 01, 2017, 09:56:49 AM »

Quote from: Void on October 01, 2017, 12:37:50 AM

Hi Itsu. That guy's explanation of his grenade winding direction was pretty poor,
but from what I could see in the video the only difference from Ruslan's way of doing it
is layer 6 is wound in the opposite direction to layer 5, rather than both layer 5 and 6 being
wound in the same direction.
All the best...

Which is not what the picture of the original aquarium coil indicates.
Plus this guy just has a coil, and no circuit, can't even say that his works any better (or at all)

itsu · « **Reply #18161 on:** October 01, 2017, 11:17:04 AM »

Chet,

i think your "stalker" his video channel is here: https://www.youtube.com/channel/UCnKiEDi9e3SyctFmLtczLBg/videos

AG, Void, d3x0r,

i agree that his presentation is not clear to me being in Russian, but Wesley is doing a good job to translate.
But in spite of that, the drawn diagram and the shot of the grenade does, imo, not match.
It could be the "Russian" way to draw up coils with their own "dot convension" meaning.

Anyway, it should be simple enough to just rewire that last 6th layer and see what kind of effect it has.

Regards Itsu

NickZ · « **Reply #18162 on:** October 01, 2017, 04:07:46 PM »

Ramset:
Yes, that is the Stalker channel, that Itsu posted a link to. Check the last two or three newer videos.
Stalker is making a new device, maybe Itsu might be interested in that device, also. As there is no grenade and no Tesla coil.
And it can produce those white streamers, somewhat similar to what Geo is showing.
Tesla also talked about bright white streamers.

Itsu: I placed the RC snubber resistors you suggested, using two 47ohm resistors in series, instead of parallel. The signal is a fairly clean square wave, still over 200v, but showing no RM. Those RC resistors are still getting hot. But, the fets are staying cool.
I'll replace the fets today with another set of brand new ones. To see if that makes any difference.

Void · « **Reply #18163 on:** October 01, 2017, 04:25:37 PM »

Quote from: d3x0r on October 01, 2017, 09:56:49 AM

Which is not what the picture of the original aquarium coil indicates.
Plus this guy just has a coil, and no circuit, can't even say that his works any better (or at all)

Hi d3x0r. Yes, I wasn't suggesting that it is good or bad or right or wrong. I just
mentioned how he appears to be winding the 'grenade' in his video. Yes, it does not
appear to match the way Kapanadze wound those last two layers in the Aquarium 2 video,
although he says this is supposed to be 'Kapanadze's secret'.

itsu · « **Reply #18164 on:** October 01, 2017, 04:51:42 PM »

Quote from: NickZ on October 01, 2017, 04:07:46 PM

Ramset:
Yes, that is the Stalker channel, that Itsu posted a link to. Check the last two or three newer videos.
Stalker is making a new device, maybe Itsu might be interested in that device, also. As there is no grenade and no Tesla coil.
And it can produce those white streamers, somewhat similar to what Geo is showing.
Tesla also talked about bright white streamers.

Itsu: I placed the RC snubber resistors you suggested, using two 47ohm resistors in series, instead of parallel. The signal is a fairly clean square wave, still over 200v, but showing no RM. Those RC resistors are still getting hot. But, the fets are staying cool.
I'll replace the fets today with another set of brand new ones. To see if that makes any difference.

Nick,

you might add another 47 Ohm resistor in series so you would have around 141 Ohm which is close to what i have (170 Ohm).
But you might see some ringing appear again.

No RM is good in my book as it points to oscillations you want to avoid.

Itsu

News:

User Menu

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY (Read 11867017 times)

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

Hoppy

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

Hoppy

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

Hoppy

Re: Kapanadze Cousin - DALLY FREE ENERGY

itsu

Re: Kapanadze Cousin - DALLY FREE ENERGY

AlienGrey

Re: Kapanadze Cousin - DALLY FREE ENERGY

Void

Re: Kapanadze Cousin - DALLY FREE ENERGY

ramset

Re: Kapanadze Cousin - DALLY FREE ENERGY

d3x0r

Re: Kapanadze Cousin - DALLY FREE ENERGY

itsu

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

Void

Re: Kapanadze Cousin - DALLY FREE ENERGY

itsu

Re: Kapanadze Cousin - DALLY FREE ENERGY