Void, 

I am just irresistible   And when he will read that grammar mistakes I made in Russian language, he will be definitely interested to see me

Void, 
I am just irresistible   And when he will read that grammar mistakes I made in Russian language, he will be definitely interested to see me

You never know. Maybe Ruslan will surprise us.
If he replies to you, tell him you will take him out for dinner if he let's you see his device in person.
I think Ruslan likes to eat.

  I just hope that the push-pull circuit can be substituted by something much simpler to replicate, even if it's not stable at first. As I have my doubts that the push-pull system with all it's needed complications, is the only way to go.  Or, to use something ready made commercially, like this PCB, below, or, a cheaper made in China knock off.

I can tell you as a matter of fact, a simple sine wave signal generator and a decent single channel audio amplifier works perfectly.  Then all you need is a current sense transformer around one lead of the induction heater coil to find the crossing point and fire your Tesla driver.  Piece of cake.

As the basics is understood we can continue on more complicated ones.
The PLL is required on changing conditions such as changed loads and changed earth ground conductivity which affects optimal frequency. So the circuit has to do same autotuning as FM radio does.

Here is one of versions with all parts together: http://imgbin.org/images/24785.jpg

Good day T-1000

This version is the *single shot* pulse generator, ie: the base/gate of VT3 receives a syncronized *single shot*  narrow (n.s.) pulse.
This was used in his less recent older version of his device.
Now he says he is utilizing *multi-shot*/packet type pulses for better effect.
Do you have access to the newer circuit topology?

take care, peace
lost_bro

Hi there guyz

yes I can still provide that simple circuit of TL witch i used, but As I see
I will be building these Oleg Circuits.
   
T-1000     Thank you for the Oleg Pdf files, and enlightment and everyone els that is helping
putting thought to this and effort.
 For Push Pull and Tesla coil driver with on/off control TL494/.
yes, the frequency will be different in each setup.

The Tesla coil Circuit setup reminds me of his first replication of the Dally Device,
It's the same one used for impulse on Coax, but now implemented on Tesla coil. hmm
This one  http://imgbin.org/images/24785.jpg
Is a worth the while shot to see if it will , will try out.
I will try to build these circuits for test.
Something is starting to make sense now.
The packet pulses is important here to fit in squar wave pulses, in my understanding,
Syncing together and locking them.

This also opens up a  new doorway for Vasmus Device understanding, It's basically same thing,
Tesla Kacher + impulse pushpull circuit on coiled plate and must sync.
Or it must be using a Thyristor for Squar pulse on reciever coils.

For what Ruslan is using now is much more complex, that is true,
So Tesla coil has to be drivin to send packets and has to be synced with Push pull in resonance.
amazing , hmm..lets see how this works out.
Bringing Voltage and Amps together as one. To resonate.

Visiting Ruslan to go see his device would be a wondrous advanture,
It would help to see and understand his device better, hopefully.

Ok Guyz,

Cheerz~

  What part is dangerous? The part about how we are all here to learn, because none of us have anything that actually works, at all? 
   It's only a matter of time before these technologies will be available. Open source is the way to assure that.
My bet is that the Chinese will be the first to market the smaller low wattage Led bulb Akula type device, to break into that untapped market, or someone else, somewhere else. It's inevitable.
  And by the time we figure it all out, it will already be available in some form, or another. 
  It doesn't matter what you or I think.  Unless you figure it all out, first.

  Alien Grey:  Your link is not showing a self running device. It should be looped, and then see what happens.
  The Russian device builders do know what I mean by capacitor/coil. Maybe you haven't heard about it.
 
  Nothing wrong with making a profit, for anyone that finds the way to make this work. Or is there?
Open source is free to use in any way at all. No restrictions. 
  This type of technology will not substitute the grid, for a long time to come, still. But, could help those that have no electricity, at all, nor money, as they are not going to be competing with the existing power companies, in any case, because they can't.
  Here for example, is one Tesla coil type of device being marketed on Ebay, as a free energy generator.
   Is it?  I don't think so...
http://www.ebay.com/itm/Mini-Tesla-Generator-Class-E-Teslaspule-4MHz-SSTC-Teslatrafo-free-energy-coil-/281260103751?pt=LH_DefaultDomain_77&hash=item417c689847

  Nor is anyone stopping them, from selling a free energy generator. Probably because it's not free energy.

  @ Tomtech: I didn't know that you've been at this since 2013. Nice ferrite cores, like I use inside my grenade
core, only yours are better. Nice video.
 https://www.youtube.com/watch?v=qAQxT7h_WGg
 
   

Talking about future, I got a bit surprise as our Czech energy company offers batteries for solar panels.  It looks like slow process of transformation begins