Nick,

The first thing to do there is to have minimum load attached and power supply connected to the output after grenade coil and diodes bridge. It has to have looped power going to the input then you can see how much is still required for circuit to run without bulbs attached.
Then you can start tuning with ground thick wire attached to the circuit. I assume your grenade coil, inductor and Tesla coil wire lengths and windings are as Ruslan described. If so then you also need to check coils polarities on connections. And all wavelengths from induction heater circuit and Tesla coil circuit should match on resonance with coils wires lengths.
One thing to note - on Skype or teamspeak it would be much more clear with understanding and diagnostics..

Be aware of changes to pulse width whilst tuning and make sure that measuring equipment is capable of giving accurate readings at various pulse widths and frequencies. Its easy to be fooled into seeing a drop of input current with a corresponding apparent increase in output and assuming that its accurate at all tuning settings. Also, never use a linear or digital bench supply in place of a battery. This is sure way to get fooled when working on Ruslan / Akula type device replications.

Nick,
I am afraid I am not only one who wants to or does change specs. In the last Ruslan's correspondence on the Russian forum he was talking about his coil tuned to 1.5MHz . It is not the same frequency he started at the binging if I good remember. 
Technically if my frequency will match the ground - I guess it is matching the impedance- it means no parasitic frequencies, overheating fets etc....??

By explanation of some people, ground doesn't supply anything. It just works as a support.  Mismatch of impedances makes an energy leakage as the support is weak. I really think we need to match the impedances.


I have made already countless number of  devices and coils , so to make one more with different specs will not kill me -It is just a hobby

Edit1:  One more thing I want to try- the pick up coil on the top of the Grenade coil ,I will make it from large diameter of wire. Experience shows that bigger wire , more amps in the loop?

Interesting stuff going on, My  guess is if your going to retune to 1m5 then to keep the Secondary coil winding in proportion to keep in tune, you might need to keep that to 2 meters 150 meg (= x100) or 300 mhz if only 1 meter is used =(x200) that's a similar ratio of 15khz to the 1.5 mhz.  of the katcher to grenade-coil. Assuming you are keeping it all tuned into proportion. i can get 1m5 out of a 4046 to see if it will tune, but 3 or 4 mm copper wire is difficult t o get with out ordering it from some where of ebay for the sec winding.

 In this forum thread in the near future.  I hope to see Oleg here.  We need him.

Might be worth a quick read while you await Energy Independence:

http://gestaltreality.com/downloads/Condensed%20intro%20to%20Tesla%20Transformers.pdf

The first page tells you all you need to know about _that_. Eric Dollard !

If you want to know some _real_ information about Tesla  transformers, you should read the work of the Corum brothers instead of wasting your time with Dollard's rantings.

http://www.teslasociety.com/corum.htm

am consuming 20 watts to produce that spark

I feel a response from TK is imminent. 

That is a good thing, because I have a question for him...

I was looking at how Ruslan uses a hard ground on the base of the secondary unlike the way Akula connected his secondary base back into his circuit as a way of feedback.  So I wondered, how was Ruslan doing this?  It is completely contrary to how a typical Slayer Exciter circuit works.  So I took a nap...

When I woke up an idea came to mind.  What if you use a piece of coax.  Use the outside shield as part of the hard ground circuit and use the inner wire as your feedback.  So I tested it and sure enough with a one meter length of 75 ohm coax I get a nice 4.8 volt peek-to-peek voltage loaded across a 5k ohm resistor.  I did probably 50 single-shot trigger tests on the scope and regardless of the input dump I use on the primary, there is that nice little feedback signal.

So before I take the plunge into implementing this into a modified Slayer Exciter circuit, I'd sure like TK's take on it and possibly a replication to ensure I'm not still dreaming.  With the items he has laying around, he could probably thumbs-up/thumbs-down this idea in 15 minutes or less.

TinselKoala!
You know the truth.
Precisely build exactly are examining all means.
Why do not you tell the truth?
Or holder of knowledge and experience.
Or you would hurt your business?
Others  of stupidity have taken advantage: ugly thing.
The opponents played dirty game.
I hope you do not.
Sorry if I'm wrong.
It's just an intuition..

Yes, I know the Truth and I'm not afraid to tell it, as I have been doing. Please point out anything I've posted that you think is not the Truth.

I have no "business" that can be hurt by the Truth.

You are right about one thing: Some people are indeed lying to you, taking advantage, playing a dirty game. I'm trying to help people to avoid wasting their time and money on the lies that you are being told by these unscrupulous fakers.

And you can be sure of something else, too: If any of these people actually have what they claim (self-runners, massive OU) it would be TRIVIAL to prove it unequivocally. But none of them have ever done so, and none of them ever will do so. Why not? The answer is simple: they cannot, because they DO NOT have what they claim, they are faking. Yes, I mean Kapanadze, Ruslan, Akula specifically.