So far, I don't see any "extra" output when the Kacher is also on. Just higher draw from whatever is used as the input source. Instead of the other way around.
   If using 100w bulbs, or higher wattage bulbs, my feed back circuit will not power the PS used for looping the device. The feed back PS will only works to produce 24v, when using a load of a single 25w bulb, or other low wattage bulbs.  How about YOU...

That's a lot of losses in the system, which is understandable in conventional terms. There just has to be a fuel involved for the claimed self-running high claimed outputs to be achieved. My hunch is that if not faked, its the yoke ferrite, assuming its the right type.

   Hoppy.
   When in the best resonant point I can power the feed back circuit, as well as a load bulb.  But, not in the best
RM mode. As the  RM has lower useable output. So far.
   My Li/ion battery pack did not work well so I'm rewiring it now.
   Also trying to buy two new 12v, 7ah batteries, if I can find some. It has not been easy to find them lately.
  While still looking for the missing link to this type of device.

 Void:
Stalker is not showing any thing self running any more, And removed the only video that showed his first self runner. And, just removed his latest video, as well. However, he is about the only one posting any videos these days, and describes them also.
  However he has several newer videos out now. But not showing any self running results, on purpose to avoid complications.
  My TL494 and driver circuit is the same or similar to what Adrian was using, which was also a Stalker replication, or version of it.  And that part works as it should.for me so far.

have another look here the yellow light doesn't help.

Hi AG. It looks like probably magnet wire on the tube, but below the tube
in that picture could maybe be some copper foil however.

All the best...

   
   Apecore: What's new with your set up?

Hi all,

Nick, my setup is doing fine, no revelations yet just obtaining the lowest power rate to go IN.
The most important item.  as where it stucks... would be the kacher part

For selfrunning stage.. we do need to lower the power in as low as we can.......  not for final end result but just to see when "back looping" will be working....  when this is reached... probally we are on a right track...
i.e. its more difficult nor almost impossible to obtain selfrunning when the system is needing 10Amps @ 24V

Probally the kacher process ....  transferring/ catalizing the energy to the grenade/ inductor by its antenna is the goal in this in a mayor way.
This is something we have not yet being able to... if someone thinks the RM mode would be this...  then again i would say bring down the input power factor and see what will happens

Until now we only have accomplished a working inductorloop... some HV/HF field effects ....  and burning scopes

We need to discuss this part of the game more.... then turning pots day by day.

What realy would maybe be of help if we would start with doing a assumption of the Mode of operandum......in order to make some progress in the mentioned kacher process
I d like to challenge Void and Hoppy to contribute in this as maybe we should start very simple and lean as normal physics should be.
Of course others are welcome to contribute to.. 100%...always better....
But focus on this item is important in the first place... (this is what i like about some other threads).
People with working setups could provide tests......  in order to verify what is proposed..

What i d like to start with, as i said lets keep it simple at the start is the following;

The grenade is a bifilar coil,....the inductor is generating a magnetic field within the bifilar grenade..
The kacher is (assuming) disturbing this inductor magnetic field and responsible for EMF in the grenade.
Important in this process as i believe is that the magnetic field from the inductor needs to "collaps" entirely whitin the grenade to obtain a significant EMF..  (Right?)
This is something we don't know if thats the case in our setups..

Besides that the whole coil/ FRES tuning wil have a increasing effect on the EMF results.....  as this is probally part of the fine tuning process

Lets assume  or just let us go by this direction......  what does this tell us bout the grenade configuration  (it bifilar shape) .....  and what kind of pulses/ waves we need on the antenna.
T1000 posted longtime ago scopeshots of effects coming from ground by pulsing a grenade..... i wonder if he has some better results yet.

Nick,... if we want to compare results we need also to do the same things with same setups,.. nescessary to find out the missing part(s)
Commitment to do the things as what is supposed ,...  meaning that if Void and/ or Hoppy are willing to contribute in helping with the theoretical part and proposing some testoptions.... we need to do as proposed,...  else it is waiste of time

I think we have some new members with lots of stuff on there bench... and willing to cooperate to find the missing part.


Greetings

Are you using an NPN power transistor to drive the katcher ? if so i bet you have the same problem I have had with every one i have tested, they do not turn off, hence the heavy current and get hot. Have you tried using a MosFet  try a IRF 450 or 460 it will work dead good with a low value resister in the gate circuit I did use a feed back winding with my experiment 10 turns  it was excellent if you want to try experimenting with it.

   Whether the extra energy comes from the ambient, or not, the important thing is for the device to be able to self run. No matter if it's getting the extra gain from the ferrite, as in NMR, or not. Then we can look into just what it is that is making that additional gain.
 
   apecore:  Thanks for your reply.
   And sorry to all for not keeping up with the postings on this thread lately. Or any other threads, for that matter. I've been trying to get all my needed batteries, and PS's etz... but it's been hard to find the batteries. I've looked for them in many places around here, but they are no where to be found.
    Do you have a feed back path set up, yet?
    Hoppy is right, we need to have that feed back path connected up onto the rest of the system, to be able to tune the device properly. As the feed back path's power supply is a big power hog to run along side the grenade and Kacher, and does not leave much juice left for the Kacher/grenade/yoke circuits to run on. And the feed back PS won't run on less than 85v, if a big load of bulbs is also loaded up.

   Even though no ones circuits are the same, they may be close enough to compare notes with.

   I'll probably have to make a controllable Kacher circuit, also. To keep up with the pack.

   Geo must be lost in space, again...  Geo, where are you?  It's 2018, already.
   Will this year be the lucky one, for us?

A little caution is needed, as a pen friend of mine ordered barium ferrites from China for a Bedini project a few years ago. However, when tested, these proved not to be barium ferrites. If anyone can source some vintage TV yokes or radio ferrite aerial rods, these could well be barium ferrite and suitable for experiments.

Hi years ago tv tubes use to have a huge neck with magnets for focus, the type that would slide over a bog roll inner sleeve, you can get them surplus from some magnet suppliers Red something or other in shefield had some, i belive they are barium.
Also Maplin Electronics do MW L Wave rods have you tried them ?  they had 100ds of them 3 years  ago when i had a pile phone them up and ask them part no LB12N

Hi years ago tv tubes use to have a huge neck with magnets for focus, the type that would slide over a bog roll inner sleeve, you can get them surplus from some magnet suppliers Red something or other in shefield had some, i belive they are barium.
Also Maplin Electronics do MW L Wave rods have you tried them ?  they had 100ds of them 3 years  ago when i had a pile phone them up and ask them part no LB12N

I've not tried the Maplin rods but I very much doubt they are barium / vintage stock. Cheap scrap vintage TV's in the Western World are like hen's teeth, so the Eastern Bloc countries are likely to be the best source, especially ferrites from ex millitary kit. Its interesting that most of the claimed self-runners come from the Eastern Bloc. I would certainly start experimenting again if I could source some suitable barium ferrites, as I'm convinced that without the right fuel material, experiments will prove fruitless.