Hello, Please be easy on me for asking stupid questions. .. Recently somebody pointed me to see the Kapanadze video and I'm fascinated by possibility of free energy. Read the whole thread watched some videos and must say I'm impressed with the knowledge here. I'm in no way close to the expertise here, but experiments are allowed so I join in.. I don't understand why you people are using a flyback coil. I thought in the latest video of Kapanadze setup the MOT was shown, I'm I wrong on this?

Hi Stefan Hi All

Thanks Stefan for the video

Question
Tariel Kapanadze devices provide full load running lights for safety time is how long? When forced to stop,when the device becomes too hot?


Havuhung

@Baroutologos and Hartiberlin

U both are right. It is having more input stored as an Initial charge in C2 4700uF. But again I just wanna say that the circuit etraps that energy and it oscillates with in the circuit. The kick offs thus produced in L1 during falling edge of each pulse are too high to drive the bulb and at the same time sends back emf to 4700uF cap. It is the same principle in which we protect input stages of Kapgen using diodes or buffers. Here I did not use any protection and the energy coming back towards C2 is charging it. And the cycle goes on till the baterry driving the pulse gen is depleted or go below 3.5V. Interestingly if I connect the load i.e 150 Ohms or greater to the circuit before switching on the pulse generator, it drains up the whole charge of c2. So the pulse gen should be powered on before connecting the load. Load below 140 ohms never allow me to re-charge the capacitor again and again. Value of C1 and L1 is calculated basing upon formula for resonant freq for LC tank cct. 1/(2*pi*Sqrt(L*C)) and is same as the freq of the pulses from 555 Timer with 50% duty cycle. U have to fine tune either L1 or C1 to achieve the resonant freq, where the bulb glows to its Max. I tuned the tank cct using LRC meter and my DSO-5200A oscilloscope. C2 4700uf has the threshold value below it i didnt get self running phenomenon and Initial charge of 24 V DC in C2 is the threshold below which Oscillation does not start rather it becomes a damping function. If u see my last two posts. The damping is clear for sometimes initially but then it is overcome by the sufficient charge c2 gets from back emf. And at 50V Initial charge it is stable from the start. I have tested it in ORCAD as well as NI multisim before i got success in hardware. LTSpice is not recommended as it gives wierd results far away from the reality.
Best of Luck

@Baroutologos and Hartiberlin
...
U both are right.
Best of Luck

Thanks for the aknowledgement Ali.
Any thoughts or observations while applying this concept in reality? Can this be so?

...
Regarding last Kapanadze video made at 2004,

Its oxymoron at least, to have an allegedly OU device and have in the same time an oil lantern in the workshop for potential power shortages?

Has anyone been able to pull any relevant information from the newest Tariel video? It appears that the spark gap terminates in the open air inside the coil. Also the cylindrical object, with the toggle switch, bears a resemblance to Hendershot generator. It has been stated that the Russians acquired the device from the US in the 1950's. Then built a base in Russia to study this device up until the late 1960's.

Regardless, is anyone in the mood and/or have time to do a translation?

-Core 

This one has also been tested with almost similar results. The oscillation starts without any delay as compared to previous one. i used 7805 for 9v to 5v DC conversion. Here is the variant. A group tried to discourage me coz they never want such simple things to be made by everyone just to have a hold on the subject. But let me tell u Now my next variant is to drive the same circuit using voltage stored in the capacitor. I am using Teslas radiant antenna (The black hole Antenna) to get collect energy from atmosphere and drive the same circuit. It's just the ingenuity of mind. Use your precious brain and we all can do it.
Credit goes to my team member Shahzeb Hussain  who recently won Pakistan Intel Prize for young Innovators.

Hello Ali,

Here is a link, reporting on your team member success and I would like to read more details if you or he could care to provide on creating electrical energy from the Earth's magnetic field:
http://www.columnpk.com/shahzaib-hussain-invents-worlds-cheapest-way-to-produce-electricity-from-magnetic-field/   What you mention above on collecting atmospheric energy to feed your circuit,  is it the same principle what your team member used?

Regarding your present circuit, can you provide a picture on the working setup at least till you can make a video? You use a ferrit toroid core, could you identify the material type or if you do not know it,  perhaps you tell the number of turns for getting 337uH or 345uH inductance, together with the OD, ID (outside and inside diameters) and the height of the toroidal core?

Thanks,  Gyula

@Broli
Well u cannot say that resonant freq calculated by the formula is also valid for square pulses. Here since it is at 50% duty cycle it is 2 time of 1KHz. If u give 2 KHz Sinusoidal it is having the same effect if u give 2KHz/2 = 1KHz pulse to the same LC cct with 50% duty Cycle. But in this case u will get higher kick offs. I practically checked that using my DDS 3x25 function gens.
As far as your java based cct sim is concerned. Try to check it again using following steps.

Place an on off  switch just before the load of 300Ohms.
Keep the load disconnected from rest of the cct by keep that switch off.
Charge the 4700uF capacitor to 50VDC.
power on the pulse generator and after a few seconds connect the load to rest of the circuit.

This is the only way to trap the energy and get oscillation.


Try this and plz let me know..

Best of Luck
Charge the capacitor completely to 50V DC.