imho ferrite core device has only weak connection with TK it's rather TPU and VTA based
You are right.
Grey Iron is ferrite based material.
So if factor of Frequency (at given other parameters)could affect and destroy molecular structure ( in NMR) that we may say about a level of interaction available.
By factor of level of interaction available.
We assume possible force and magnitude of forces of interaction.
And by assumption me may apply such potency of expected magnitude to become kinetic force affecting interaction with any other MUT.
Than we exclude MUT that is non promising leaving on the table only what you think might interact.
Wesley
PS:
If SR used NMR effect than it was possible that NMR might interract with ferrite at given permeability, to the certain energy level. (he said only 150W)
But when you look at videos from my post before than you will see 3 coils.(NO FERRITE) One of them was strange...
Than on the drawing you see two coils vertically and the guy says
that these coils must be winded this way that magnetic field is opposite... for me that is counter and clockwise...
Like in Tesla drawings.
The coil of strange winding made on flexible plastic is actually two coils.. giving XYZ of Cartesian geometry.
Notice that magnetic field of earth is the factor interacting with NMR .
PS#2:
Energy factor PF is the level over the time which stands for consumption.
From that perspective the shortest the impulse the higher is energy potential .Another words if potential energy is to be in impulse of 1 microsecond than total power of that impulse might be in hundreds of KW region as if the same potential energy
could be having power of watts only.
Let's use another example..
You might pickup something heavy with rapid lifting and short time to hold.
Than the time you are able to hold it stays about your energy reservoir
From that moment it is just pure energy consumption.
So if you had to lift it 10 times for short time .. you would do it easier than
Hold it to consume the same energy.And after that you have no longer ability to perform again.
or
You know that there is no need for you to lift it more than one time.
Now all of energy is directed to one impulse only.WOW now we have one big impulse..
Relatives of this is snapped to time and area of impact.
Say needle with potential energy converted to kinetic one of
1kg is heaving the same effect as 1000kg on iron rod of Fi=1"
on the same surface.
than total KW power per area is equal but energy level to make the same work is different.
As far as flyback ..what is important is shape of square wave.
After flyback it is more sign than square. Than if you assume that when you have ratio not 1:1000 but 1:10 than you see that your transformer is performing better square.
Ok so than we think about starting delivery of square signal from say 200V level instead form 10V level. to primary of flyback of ratio 1:20 that = 4000V
But square of it is much closer to perfect one than one coming from regular TV flyback.
Generally to make initial 200V square is not difficult at all.
So How do we do it.
The simplest way is to buy from ebay amplifier for few dollars.
Say Trek 601B
or HP461A,HP462A much better is HP 465a - this one does not have BNC but banana connector perfect. Than connect it to your 10V 1transistor generator.
Another approach would be pulse forming network PFN this is super shape solution but there is the catch. Frequency of the PFN has to be known prior to purchase. If it is made to work with 100hz to few KHz it is waste of money even if it looks gorgeous .. Do not buy it. The frequency we are interested with the most is 20-100kHz ..another frequency range suggested is arround 600-850KHz.
There is none of PFN I know about that would cover these two ranges in one unit for Square Wave.
Important factor is impedance matching network
What we have to understand that most of devices on the market is made for 50 OHm impedance of resistive nature.
Well our load is somehow complicated.
If we talking about coil that Flyback is connected to than this coil is the load for Flyback AND THAT IS INDUCTIVE LOAD and impedance of that coil should be 50 Ohm with respect to commercially made elements.The difference is made by adding spark gap.
The next step would be to find out if we really need 50 Ohm?
Well No we do not need it..
The only consideration is to make impedance match by tuning structure to resonance.
The only moment that we might have spark gap in NMR is if it is used to form the pulse.
Usually forming pulse is done with very low energy levels i traditional NMR.
and is not using spark gap not HV.
remember that in traditional TK suggested chain of reaction is:
- generator at low voltage square impulse
- voltage amplifier ( if you wish to start from level of square at 200V)
- HV transformer 1:20 ratio
-secondary of HV Transformer is connected to spark gap and this spark gap is just creating HV impulse that is triggered by impulse of flyback..
Ideally all we need is spark creating our square wave..
So if You know of any other possible way or technique to trigger spark that it starts giving you nice clean regulated interval of spark.. than nothing before I have described about pulse creation is important any longer.!!!!!!!!!!!!!!!!!!!!!!
So modified NMR might be the way to couple to OU.
Another limitation is the core of transformer if it is ferrite (not Permalloy 1000hz max)
Than for permeability of 2000 you can go easily to 15kHz.
The better the square at the HV the better the result as you dealing with brought range of sign wave components in single square impulse is made from.( whan you make FFT(fast Furrier)
Than you see sign wave components. Filters make only part of these components to pass true.. so energy level of such signal is close to sign wave.. Flyback is a filter as well.
that is where you have loses..
But you do not care about the loses after you are able to feed back generator from OU.
The key point is that first you have to have short burst signal impacting "small area" of MUT than when you see response you no longer care about impulse at all.
It is like first intercourse after that there is less energy needed as barrier is no longer there.
Statement to memorize
Subiect
-measurement signal output from secondary winding of transformer
Result
If that impulse shape differs from impulse delivered to primary than
-it is directly proportional to the energy dissipation
-the HV transformer ..reacts always as filter with respect to input square.
-frequency spectral component of input square wave has always more energy
-Frequency spectral component of square signal (analyzed in Spectrum Analyzer) represents total power delivered so if we are able to see non perfect square at secondary we know that all of the missing components represents losses.
Spark made fire.. Look at the energy level of spark..
The spark could interact with energy storage wood..
The whole secret of OU is just to use storage that we do not have to pay for.
It is here and nobody is charging for it.for. Unless some of governments will start to charge for use of fresh air?
))))))))
Ps#3:
Pulse forming network is important for power transfer and impulse shape
Sphere Gaps
http://home.earthlink.net/~jimlux/hv/sphgap.htmQuote:
"A spark gap will have a very repeatable breakdown voltages for a given atmospheric conditions. For mostly mechanical reasons, uniform field gaps (using, for example Rogowski or Bruce profile electrodes) are not used as much as sphere gaps where the spheres are quite a bit larger than the gap. There isn't a convenient analytical expression for the breakdown voltage as a function of sphere diameter and gap, as there is for a uniform field gap, however, there is a lot of empirical test data, and sphere gaps are by far and away the most common way of measuring high voltages with a spark gap."
That is another factor important in our project.
the general information in broad view is given in link:
http://home.earthlink.net/~jimlux/hv/hvmain.htm#TOC
