Been working on perfecting a 'discharge' circuit for my coil. This circuit I believe is more like a Disruptive charging then Disruptive discharge. I am utilizing an inductor to increase the charge on a capacitor. What has me surprised a bit is how much additional charge over input voltage can be added to the capacitor. In the below wiring diagram points 'A' and 'B' are my rapid break points. Depending how fast you break the points negotiates the amount of charge sent to the cap. The faster, the greater the charge.

  At power up the capacitor is charged to 150 volts, depending how fast I short points A and B I can raise the charge to 220 volts. One question I have is 'Why does the sudden disruption across the cap. raise the voltage so much higher?' I'm guessing it has to do with the rapid creation then collapsing of the magnetic field in the inductor. Another question is 'Why does the speed of disruption between points 'A' and 'B' vary the voltage widely'?

  As far as controlling the circuit can anyone recommend a Transistor or Mosfet that can handle the power switching. I also build a mechanical break with a DC motor. Unfortunately the points I used where not 'beefy' enough and disintegrated within thirty seconds or so. Any advice on how to make and break the points electronically would be appreciated. I know some transistors have some 'bleed through'. To get maximum voltage rise there can not be any bleed through it must be solid 'on' and 'off' very disruptive.

  In the mean time I an designing a new mechanical fast switching break. Any idea's?

Respectfully,

Core

Try a small HV supply.  Like the flyback type that put out a few KV at a few mA's.   TK's green box gap looks like the current is pretty low.

Several Tesla Builder sites have plans for rotary gaps, or use some sort of HV switch.

   What does this mean exactly? What is this myth of "Cold" electricity again?

I was just commenting on an interesting post.  Whether or not cold current exists and what it is, is anyone's guess.

Grumpy,

Trying to piss me off?


The fact of the matter is I could clear this whole Kapanadzi mystery up in a single post and you know that because I gave you a document to post a year ago that explained the principle. (Look towards the end) I have also posted how to info. all over this web site. The funny looking end of the coil "should be obvious".

My guess is you know the 1 year disclosure clock has run out and you are trying to get another disclosure to make sure I can't patent and go into production or share the payoff money. Don't worry, that isn't my game. This is pure amusement for me.

My next guess is that you are trying to get Kapanadzi's registered trade secret nullified somehow. Seems we have been using so much counter intel on each other over the years, I am starting to get confused as to what side, who is on. I spotted you early and was also feeding you info. but only to lure you into my lair. You have been most helpful.

Bolo's compressor analogy was priceless. While I play dumb and make fun of it, don't think for a second I am half as dumb as I pretend. One end of the coil is probably going to emit some accelerated particles that need to be shielded with some borated polycarbonate or lead.

Watching you trying to disqualify SR193 is most telling. Maybe you are not smart enough to realize that SR193 didn't have the two bucks to buy what is over one the end of the TK core and instead placed it inside because that is what he had laying around. Or... Maybe you are as dumb as those that decided it was not Kapanadzi's replication because you didn't think it through...

All you have done is make suggestions as if they were fact and talk a bunch of noise.  If you really are all that and a bag of chips, then prove it.

You'll come back with the usual BS about people trying to get you to disclose something or some BS about oppression.  The only oppression and disinfo on this site is from forum trollers like you with your endless BS and derogatory comments.

Save it for the other clowns, CLOWN!

Per the green box:

The visible  - adjustable - spark gap has nothing to do with the primary side circuit.

I believe it sets the discharge rate of the output capacitor, allowing him to adjust the conventional current and voltage supplied to a given load.

i.e. bigger gap = capacitor reaches a higher voltage = more current and a lower cycle rate

The primary side circuit frequency adjustment is most likely a variable vacuum capacitor ( as a component inside the green box )

Hmm  so maybe small cap HV on a rotary switch would not be so bad on the contacts.  Core, were you running the 80uf cap on the failed rotary switch?  Maybe that was the cause. Welding.  ;]

Mags

Here is a vid I did using a small neon transformer from a copier/scanner charging my discharge cap via an AV plug made with 2 1kv diodes. Notice the input current when idle and just normal sparking. The AV plug does create a higher draw from the batt than if the neon transformers sec were just open.

Anyway, hope this inspires a direction for parts lists.  The sidacs are described in the vid and a fun to use. Solid state spark gaps.  ;]

Mags

http://www.youtube.com/watch?v=TR3WmK3qrws

All you have done is make suggestions as if they were fact and talk a bunch of noise.  If you really are all that and a bag of chips, then prove it.

You'll come back with the usual BS about people trying to get you to disclose something or some BS about oppression.  The only oppression and disinfo on this site is from forum trollers like you with your endless BS and derogatory comments.

Save it for the other clowns, CLOWN!

How original... "Clown".

Shouldn't you be over at OUR? You wouldn't want to miss Looney Larry's evening services now would you?

I seem to recall you telling me "thoughts are free but if you build and demonstrate they will come down on you hard". Knowing who you were, I took that as good advice. I even got you to convert a word doc. into a pdf and post the big secret online - tool! 

Within the last 25 pages of this thread, Kapanadzi's big secret was disclosed. It was just a thought and obvious to anyone with two eyes. The metal rod through the center just holds the two sections all together.

See what happens when you piss me off? I share more thoughts. That would be counter productive in your line of work. The offer still stands. Tell your evil overlords for 100K, I will stop disclosing OU info. It went back up to original offer when I reversed engineered Kapanadzi. That one is so simple a child could build it. So similar to the AH coil it hurts to keep it inside.