Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: System spikes 12vdc  (Read 5271 times)

UKpirate3000

  • Newbie
  • *
  • Posts: 2
System spikes 12vdc
« on: April 21, 2009, 12:09:14 PM »
Hi All, Apologies if I’m a bit of subject, this is my first post on this fascinating site recommended by a regular contributor. I live on a boat in the UK I run mostly 12 volt systems. The water Pump a Par max 4  model 31620-0292 keep failing, they don’t seem to burn out just stop working. My system consists of 6 Hawker powersafe 12v105f (105amp) power cells a silverline cb20-1 charger set to min 12a. This is charged to a stephill generator putting 220volts of fairly stable modified sine wave power, run for on average 2.5 hours a day. The max draw of the pump is 6amp at 10PSI and fuse rated at 10 amp. I think I need a put a 10 amp Diode in line on the positive, do you think this solve the problem? If so and ideas where I could buy one in the UK I’ve looked on line but to be honest, always best I find, I’m not sure what type of diode I need. Any advice with problem or potential suppliers would be greatly appreciated.

Thaelin

  • TPU-Elite
  • Hero Member
  • *******
  • Posts: 1093
Re: System spikes 12vdc
« Reply #1 on: June 08, 2009, 12:32:22 PM »
   I feel the best thing to do there is to take one apart and trace the power
through it until you lose it. From what I gather, this is an AC motor driving the pump. With that, I would almost suspect the start/run cap going. That in its self dont sound right as I have seen motors run just fine. Contact the manufacture and ask if it is suited for modified sine use. That would be a good start anyhow.

thaelin

fritz

  • Sr. Member
  • ****
  • Posts: 424
Re: System spikes 12vdc
« Reply #2 on: June 08, 2009, 01:50:46 PM »
... the PAR MAX 4 is a DC pump available with 12/24V (!??)
So for the failing issue - the only stuff I can think of is that the brushes wear out .... but this sounds different.
Is there a thermoswitch inside the motor - which protects agains overheating ?
Does the puimp resume operation after failing ?
Using short wires with proper and even oversized diameters can be suggested.
The wear out of the brushes (but I dont think its this problem) and the emitted rf interference / back EMF of the pump can be affected by an external cap bank placed at the motor connectors - a bank of 10 x 470n / 63 V ceramic caps may help here.
If its a thermoswitch thing - cooling might help to extend the operating periode...


Groundloop

  • TPU-Elite
  • Hero Member
  • *******
  • Posts: 1736
Re: System spikes 12vdc
« Reply #3 on: June 08, 2009, 02:16:08 PM »
UKpirate3000,

Let us see, you pump is a 12 VDC 6 AMPERE pump. You must use a 12 VDC 10 AMP fuse. A normal car fuse for 10 ampere will do fine. Your pump has a thermal protection system built into it to protect against over heating. The pump needs air to cool down. If your pump is mounted into a closed compartment without circulating air, then it will shut down when it gets warm. Make sure that the pump has enough cooling. If there is a lot of noise on your 12 volt system (because of inverter load etc.) then use a 10000uF 25 Volt electrolytic capacitor mounted close to the pump terminals. + on capacitor goes to + on pump and - on capacitor goes to - on pump.

So, good cooling by using circulating air and one electrolytic capacitor for noise suppression.

Data sheet for you pump can be found in the download section of this forum:
http://www.overunity.com/index.php?action=downloads;sa=view;down=284

Regards,
Groundloop.

Thaelin

  • TPU-Elite
  • Hero Member
  • *******
  • Posts: 1093
Re: System spikes 12vdc
« Reply #4 on: June 08, 2009, 07:49:23 PM »
   OK, my bugger there. DC. I did a external heat sink on a dc motor by wire tieing aluminum to the body with a dab of gel under it. Helped it a lot.