Author Topic: Sjack Abeling Gravity Wheel and the Worlds first Weight Power Plant (Read 782641 times)

mrsean2k · « **Reply #495 on:** April 12, 2009, 07:37:48 PM »

Quote from: Cherryman on April 12, 2009, 07:27:34 PM

Great work!

Can you rotate the imiges who stand sideways now?

Ok, slightly better:

http://docs.google.com/Doc?id=ddr3zqdb_14fwv39dgr

AquariuZ · « **Reply #496 on:** April 12, 2009, 07:42:18 PM »

(cont)

         Each of the weights 3 is movable in a radial direction in an accompanying guiding
10      track 8. Towards that end the weights 3 as shown in the example are installed in pairs. Every
      weight 3 has a joining bar 10 which connects both weight parts 11 and is held by guiding track 8.
15      These joining bars 10 move in a radial direction in guiding track 8.

      In an alternative setup of the conversion unit the edges 212 of each guiding track 208 have a
20      serrated surface to minimize friction as the weights make their sliding motion (fig. 6). The joining
      bars 210 of the weights are ovally shaped here to ensure regulated motion over the serrated
      surface 212. It should be noted that this setup shows that the guiding tracks 208 can be
25      distributed non uniformly around axle 206.

AquariuZ · « **Reply #497 on:** April 12, 2009, 07:54:43 PM »

(cont)

In the example show the guiding materials 4 consist of two installed
      rings 13 which are installed on both sides of carrier 2, along which the weights 3 are movable.
30      These rings 13 in this example have been cut out of side plates 5. The rings 13 run in a horizontal
      direction which is eccentrically in relation to the rotational axle A of carrier 2, and have a slightly
      oval shape, whereby the long axle is aimed vertically. In fact the rings 13 have the shape of

               ( 8 )

      an indented circle. Because of the shape of the rings 13 every weight 3 when it reaches the pinnacle
      of its path around axle A, or slightly before, is accelerated strongly in a radial direction. Because of
5      this a lot of energy is released. The long axle of every ring 13 is slightly tilted in such a way that the       weights 3 are forced back inwards even before they reach the lowest point of their path.

AquariuZ · « **Reply #498 on:** April 12, 2009, 08:17:46 PM »

(cont)
         The conversion unit 1 in the example shown is furthermore fitted with secundary
10      bearing means 14, which are fitted around the circumference of carrier 2. These secundary bearing
      means 14 consist of a number of spacers 15 which run from carrier 2 to each of the side plates 5,
15      and a bearing ring 16 which houses the spacers 15.
      Each bearing ring 15 (16?) runs on the outside with a spacing around guiding ring 13 (fig. 3).

            The path each of the weights 3 takes during the rotation of carrier 2 around
20      the axle line A is represented in fig. 4. Assuming the position on the top right (indicated as 3Â°) the
      weight moves down under the influence of gravity, whereby it will attempt to move away from axial
      line A in a radial direction along its guiding path 8 while influenced by the centrifugal force.

AquariuZ · « **Reply #499 on:** April 12, 2009, 08:35:32 PM »

(cont)

25      This radial movement is restricted by guiding rings 13. When the weight almost reaches its lowest
      position 3-5 the radius of guiding ring 13 starts to diminish, which causes weight 3 on its upwards
30      motion to be forced into a radial direction towards axial line A. At around the level of axial line A
      the radius of guiding ring 13 starts to increase again, which causes weight 3 to move outwards
      again starting at position 3-12. This means in essence that weight 3 is being "hurled".

AquariuZ · « **Reply #500 on:** April 12, 2009, 08:43:51 PM »

(cont)

               (9)

      Due to the variation of distance of the weight with respect to the axial line A, a rotational
      momentum   is generated which is translated to axle 6.
         Even though fig. 4 shows the motion of a single weight, it will be evident that
5      all the weights follow an identical path. This is shown in fig. 5A to 5D, where a setup of the
      conversion unit 101 is shown with four weights 103a-103d and guiding tracks 108. In these
10      views is shown how weights 103(a red.)-103d move from and towards each other.

AquariuZ · « **Reply #501 on:** April 12, 2009, 08:56:50 PM »

(cont)

         In the setup of conversion unit 301 which is currently being prepared for practical
15      application tests there are placed two carriers 302 next to each other with spacing (fig. 7). Each
      weight 303 is shown to have a joining part 310 which protrudes on both sides through the guiding
      track 308 in both carriers 302 and into the rings 313 of the guiding materials 304. The guiding tracks
20      inthis example have the shape of a hockey stick; they are in essence straight and only have a curved
      segment on the radial far end 309 (fig. 8 ) Because of this shape the weights 303 are subjected to
      a short but violent hurling motion. It should be noted that the straight parts of the guiding tracks 308
      are not purely radially aligned but rather are slightly offset with regards to axial line A.

AquariuZ · « **Reply #502 on:** April 12, 2009, 09:07:26 PM »

(cont)

         Even though the invention has been explained through a number of examples it should be
30      obvious that it is not limited to these. There could be more or less carriers and weights than previously
      shown, and the carriers and weights could also have different shapes and dimensions. For example the
      carrier instead of being a disc shape with guiding tracks could also

                  (10)

      be constructed as a wheel with spokes with sliding weights.
         The extent of the invention is therefore solely determined by the following conclusions:

AquariuZ · « **Reply #503 on:** April 12, 2009, 09:31:55 PM »

(cont)

                  (11)

Conclusions

         1. Installation for the conversion of gravitational energy into motional energy, containing:
            - at least one rotatable carrier with a horizontal axle with at least one attached
5      weight which is mainly radially movable relative to the axle, and
            - means collaborating with the carrier to guide the radial movement of the at
      least one weight .
10         2. Conversion unit according to conclusion 1, with the feature, that the guiding
      materials are setup to move the at least one weight near the top of its path around the rotational axis
      away from the axle in an accelerated motion.
15         3. Conversion unit according to conclusion 1 or 2,with the feature, that a number
      of weights is attached to the carrier in a circumferencial way.
         4. Conversion unit according to previous conclusions,with the feature, that the
20      or any weight is radially movable on or housed in the carrier.
         5. Conversion unit according to conclusion 4,with the feature, that the appearance
      of the carrier is a disc, on which or in which a mainly radially guiding track is formed for the
25      or any weight.
         6. Conversion unit according to conclusion 5,with the feature, that the or all guiding
      tracks at least has a curving segment in the rotational direction on the its far end away from the axle.

hartiberlin · « **Reply #504 on:** April 12, 2009, 09:37:53 PM »

Quote from: Cherryman on April 12, 2009, 06:48:20 PM

Hi guys, im still alive!The MIB were tough but i resisted!

Had a quick look at the patent, "curved ramps"

Anyway.. here is a quick start to play with.

Timing, weight.. will be critical.

Hi Cherryman,
the guiding barrier track number 13 in picture 8 is still missing in your WM2D model.

Well,. we will see, if this Abeling patent model will really work via simulations.

Many thanks for all, who helped translating the patent.

Am just back in from 2 days away and have to study all the recent postings.
Regards, Stefan.

Cherryman · « **Reply #505 on:** April 12, 2009, 09:48:09 PM »

If you ad the rails you will get this , principle. I tested that... Sjack has to have something else added...

http://www.youtube.com/watch?v=GBygA2vOHx4&feature=channel_page

I

Cherryman · « **Reply #506 on:** April 12, 2009, 09:53:55 PM »

Here a version with the rails

AquariuZ · « **Reply #507 on:** April 12, 2009, 09:55:49 PM »

(cont)

                  (12)

         7. Conversion unit according to conclusion 6,with the feature, that the or all guiding
      tracks show a hockey stick pattern.
5         8. Conversion unit according to conclusion 6,with the feature, that the or all guiding
      tracks show a smooth flowing curvature over its entire lenght.
         9. Conversion unit according to one of conclusions 5 to 8,with the feature, that the
      or all guiding tracks have at least a partially serrated surface.
10         10. Conversion unit according to one of conclusions 5 to 9,with the feature, that the
      or all weights are divided and connected by a pertruding joining part through the guiding track in the
      disc shaped carrier.
15         11. Conversion unit according to one of conclusions 5 to 9,with the feature, that
      two disc shaped carriers with spacing are placed parallel to each other and share one or more weights
      which are installed in the spacing between, and the or all weights show a pertruding joining part on
20      both sides of the disc shaped carriers.

         12. Conversion unit according to one of the previous conclusions,with the feature,
25      that the guiding means consist of at least one parallel to its rotational plane covering ring placed next to
      the carrier, along which the or all weights are movable.
         13. Conversion unit according to conclusion 12,with the feature, that the guiding
30      means encompass two on both sides of the carrier placed rings.
         14. Conversion unit according to conclusion 12 or 13,with the feature, that the or
      any ring runs in an eccentrically horizontal direction with regards to the rotational axle of the carrier.

NerzhDishual · « **Reply #508 on:** April 12, 2009, 10:03:27 PM »

Nil
Void
Nada
Niente
Rien
Que d'alle!

AquariuZ · « **Reply #509 on:** April 12, 2009, 10:08:38 PM »

(cont)

                  (13)

         15. Conversion unit according to one of conclusions 12 to14,with the feature, that
5      the or any ring shows a mainly vertically aligned oval shape.
         16. Conversion unit according to one of the previous conclusions,featured by the
      installation of secundary housing materials around the circumference of the carrier.
10         17. Conversion unit according to conclusion 16,with the feature, that the secundary
      housing materials contain a number of spacers which run from the carrier towards the guiding materials
      and are housed by a ring which is placed around the guiding materials.
15         18. Conversion unit according to one of the previous conclusions,with the feature,
      that at least the carrier and/or the guiding materials are contructed out of glass.

END OF TEXT

Cookie	Origin	Persistency	Information and Usage
ecl_auth	overunity.com	Expires after 30 days	This cookie contains the text "EU Cookie Law - LiPF cookies authorised". Without this cookie, the Forums' software is prevented from setting other cookies.
SMFCookie648	overunity.com	Expires according to user-chosen session duration	If you log-in as a member of this site, this cookie contains your user name, an encrypted hash of your password and the time you logged-in. It is used by the site software to ensure that features such as indicating new Forum and Private messages are indicated to you. This cookie is essential for the site software to work correctly.
PHPSESSID	overunity.com	Current session only	This cookie contains a unique Session Identification value. It is set for both members and non-members (guests) and it is essential for the site software to work correctly. This cookie is not persistent and should be automatically removed when you close the browser window.
pmx_upshr{NAME}	overunity.com	Current session only	These cookies are set to records your display preferences for the site's Portal page if a panel or individual block is collapsed or expanded
pmx_pgidx_blk{ID}	overunity.com	Current session only	These cookies are set to records the page number for the site's Portal page if the page for a individual block is changed.
pmx_cbtstat{ID}	overunity.com	Current session only	These cookies are set to records the expand/collapse state for a CBT Navigator block content.
pmx_poll{ID}	overunity.com	Current session only	These cookies are set to records the id for the current poll in a multiple Poll block.
pmx_{fadername}	overunity.com	Current session only	These cookies are set to records the state for a Opac-Fader block.
pmx_LSBsub{ID}	overunity.com	Current session only	These cookies are set to records the current category and the state for a static Category block.
pmx_shout{ID}	overunity.com	Current session only	These cookies are set to records the current state of a Shout box block.
pmx_php_ckeck	overunity.com	Page load time	This cookie will probably never see you. It is set, if a Syntax check on a PHP block is initiated and will be deleted if the function executed.
pmx_YOfs	overunity.com	Page load time	This cookie will probably never see you. It is set on portal actions like click on a page number. The cookie is evaluated on load the desired page and then deleted. It is used to restore the vertical screen position as before the click.

1	We are aware that Google uses additional cookies it stores on your PC and when you browse our site and all other sites. These are used to target advertising and Google currently does this without seeking your permission. Four of these cookies we know about are named "rememberme", "NID", "PREF" and "PP_TOS_ACK" and are stored in Google's cache on your computer.
2	If you are accessing this site using someone else's computer, please ask the owner's permission before accepting cookies.
3	Your browser provides you with the ability to inspect all cookies stored on your PC. In addition your browser is responsible for removing "current session only" cookies and those that have expired; if your browser is not doing this, you should report the matter to your browser's authors.
4	We regret and apologies for any inconvenience this causes to members and guests who are accessing our web site from outside the European Union. It is not currently possible for us to interrogate your browser and obtain geographic location information in order to decide whether or not to prompt you to accept cookies.

News:

User Menu

Author Topic: Sjack Abeling Gravity Wheel and the Worlds first Weight Power Plant (Read 782641 times)

mrsean2k

Re: Sjack Abeling Gravity Wheel and the Worlds first Weight Power Plant

AquariuZ

Re: Sjack Abeling Gravity Wheel and the Worlds first Weight Power Plant

AquariuZ

Re: Sjack Abeling Gravity Wheel and the Worlds first Weight Power Plant

AquariuZ

Re: Sjack Abeling Gravity Wheel and the Worlds first Weight Power Plant

AquariuZ

Re: Sjack Abeling Gravity Wheel and the Worlds first Weight Power Plant

AquariuZ

Re: Sjack Abeling Gravity Wheel and the Worlds first Weight Power Plant

AquariuZ

Re: Sjack Abeling Gravity Wheel and the Worlds first Weight Power Plant

AquariuZ

Re: Sjack Abeling Gravity Wheel and the Worlds first Weight Power Plant

AquariuZ

Re: Sjack Abeling Gravity Wheel and the Worlds first Weight Power Plant

hartiberlin

Re: Sjack Abeling Gravity Wheel and the Worlds first Weight Power Plant

Cherryman

Re: Sjack Abeling Gravity Wheel and the Worlds first Weight Power Plant

Cherryman

Re: Sjack Abeling Gravity Wheel and the Worlds first Weight Power Plant

AquariuZ

Re: Sjack Abeling Gravity Wheel and the Worlds first Weight Power Plant

NerzhDishual

Re: Sjack Abeling Gravity Wheel and the Worlds first Weight Power Plant

AquariuZ

Re: Sjack Abeling Gravity Wheel and the Worlds first Weight Power Plant