Basically a wheel with attached pivot arms at various locations with proper stands holding the whole machine.  Timing of pivot arms and wheel simultaneously to create repelling action and thus turning wheel.  More than one pivot arm is needed needed due to the mass of wheel.  There is a little something to go on.  Please wait for video, it will come in due time

Mr. Sterling:
For your information,  I have also received plenty of threatening emails on this website for my invention that I posted last year. You just have to accept skeptics that do not believe in things like this.  I appreciate everything that you are doing with magnet polarities but I hate to burst your bubble.  As I posted on my website, about 15 years ago, I went through all of Howard Johnson's diagrams inside and out and went through dozens of different magnets.  I used C magnets on a disc just like he did. With a large C magnet to rotate the wheel, I did many, many tests from every different angle possible, moving the magnets both North and South, repositioning them.   The design he has will never work.  For all the testing I did on the magnet wheel, I found out that using strip magnets at a 45 degree angle on the disc, standing on edge, was about the only thing I could come up with to make the wheel turn using a large C magnet to push the strip magnets on the disc.  Again, I appreciate all you are doing to further free energy but I have been through this and I've done his design. With all this said and done, you will probably never get to see his machine and he will most likely come up with excuses all the time.  Furthermore, listening to his videos, every time he starts the disc you will hear some kind of starter motor noise in the background. Even if he does a demonstration on a glass table and he has some kind of starter motor, you will still not see it.

  As I told you over the phone I will be having Jim Dunn and Ted Loder down here to document my machine when it's ready - and that will be soon.  Good luck on your work.

James

Spinner and Omega_O,

I probably should have never brought up things I have done in the past.  It is true that I made a magnet wheel ten or twelve years ago.  Sorry you don't believe in me but I did it.  I have no reason to make up stories on this website.  Making the new video, I have truly been having problems and it takes time to solve problems when changes are made.  It seems like so many people doubt my credibility because things I do are hard to believe and are against convention beliefs.  But everything I say is the truth and I'm getting tired of having to give explanations to people on this website.  As I explained in earlier comments, there are a lot more people working on this than me.  I was warned not to go on this type of website because of skeptics and nonbelievers.  Most of the people pick on anything they can find.  I still would like to thank people for all the good comments but I'm really thinking of cancelling my membership on this website.  The machine will be getting documented as soon as possible.  Likewise, the new video will be out as soon as possible.  But I'm finished for now on this website.  I will not be back to reply on any comments until the documentation is complete and the video is finished.  Good luck all.

James

I just got home from work and have read everyone's comments.  I'm glad everyone is trying to figure this out.  About ten years ago I was fixing VCR's and TV's for people - I would have 10 VCR's on my kitchen table and 15 in the closet for spare parts.  When my son's hamster died, I took the hamster wheel and added magnets to it.  I went through so many different angles on the magnets to try and make the wheel spin using a large magnet to bounce off the hamster wheel.  I finally, after numerous trys,  had the wheel spinning on its own.  But this is just an old story.  A lot has happened since then.  Two years ago I started back piddling around in the garage with high pressured water and different sized pulleys.  I hooked up an electric motor, eliminating the water pump and went through so many different dimensions with the belt drive directly to the generator and I found out that using a shaft with pulleys gave me the best results.  At this time, I asked an old friend of mine who rebuilds generators and motors if he would help me out and he brought some friends with him and we all came up with what we have today.  This video was made last summer and many changes have been made since that time.  The generator is now back over at the shop and it's being rebuilt.  I've also added a lot more paddles to the wheel.  I can't say much more because my partner is the generator guy.  I'm going over to his house in about five minutes to give him a hand.  Again, thanks for everyone's input.  I'll print all of this and take it with me tonight and show it to my partner but he seems to know what the problem is.  I'll get back to everyone when the generator is back here in the machine and it's working - hopefully, this weekend.

James

This is beginning to look like a clone of the Archer thread.  7 pages in one day so far and nothing has been said. You only have another 650 or so to go to beat Archer 

Hans von Lieven

a) A number of universities refuse to let their names be used on a report
of overunity energy production because of "negative future ramifications"
of such a report. People tend to get funny about the truth, especially
when it comes to their paychecks.

So you may be able to get a professor to state what he sees but;

b)In a number of cases machines have been sent out to universities only
to come back as "not working". Because undergrads have gotten a hold
of them and solved their "problems".

Their bread is buttered by the state.  Their research grants are provided by the Feds.

They know who signs their checks and when someone says kneel down or shut up, they do so.

You've probably heard a lot about recent university discoveries in exciting fields such as photovoltaic paints.  Like to know how they work so you can make some?  Sorry, that's licensed and patented.

Did you know that simple corn gluten meal was a powerful pre-emergent for weeds?   If you do want to sell a product and make that claim, you must pay the license fees to the University

Unfortunately, a university will take ownership of any idea