Bob, Crazycut06, Magluvin,...all
I have a proposal: to work like a  team involved in a project. That because all, we have a lot of ideea, different materials(we are around the world...). Step by step we must to validate(almost all or majority of us) every stage. Personally I'm determinated to make a device OU reproductible by every person who have some skills on electronics...I claim that beacause, all of us, see here and another forum that good intention and good skills are lost; work conditions are very different and MEASUREMENT are some trap. Maybe  some are good in theory and don't have equipment, some in theory and practice, etc... Is simple to post some scheme(real and good intentions!) and after a lot of people work to reproduct...without result, inoperative. After, people become nervous, debate is ... religious without link to OU!!! So time go, and go and i don't know if OU come only from word... So my opinion is to concentrate to define a block diagram. Next define and practical realise and measure every block. We move to next block after most of us obtain same results! May take a time, but result is guaranteed!!!
Now I want to know your opinion about this organized manner of work.
Good luck, a lot of healthy to you and yours familly!!!

Mags, I like your idea about wrapping the secondary around the primary, but also around a second coil.  But first, let me backtrack a bit:

These are a lot of what Tito had talked about. In the ruff.  ;]

But I believe that there must be a way to have a self increasing oscillation. Either it can be started, kicked, then once it has self increased, then discharge to load or storage.

Do you think that if we're dealing with a coil of iron wire (perhaps a shorted coil), that its magnetic current might be helped along (sped up) by bringing it into contact with a magnet? Maybe this would get our "kicks" going.
 
I used germanium diodes with mine, but I think my caps were too large. Perhaps we need verrry low voltage caps in order to charge up and kick. Back to the bench when I get time.
 
Guys, I like your enthusiasm for a focussed collaboration. I just don't have the time, with multiple projects on the go in other areas of life. I'm glad to contribute the little I can to this thread.
Bob

Mags, I like your idea about wrapping the secondary around the primary, but also around a second coil.  But first, let me backtrack a bit:Do you think that if we're dealing with a coil of iron wire (perhaps a shorted coil), that its magnetic current might be helped along (sped up) by bringing it into contact with a magnet? Maybe this would get our "kicks" going.
 
I used germanium diodes with mine, but I think my caps were too large. Perhaps we need verrry low voltage caps in order to charge up and kick. Back to the bench when I get time.
 
Guys, I like your enthusiasm for a focussed collaboration. I just don't have the time, with multiple projects on the go in other areas of life. I'm glad to contribute the little I can to this thread.
Bob

Hey Bob

Well, maybe I should describe that better. Ill attach the pdf of the multi core inductor/transformer below. Ive posted it before, but who wants to go back and find it, when I gots it right here. ;]  Some people will make ya go find it. 

Imagine a toroid core with a primary on the one side and the secondary on the other. So instead, when winding the secondary, loop it through an additional core.

Or wind the toroid as a normal transformer, primary and secondary, and, get another toroid core and wind on it, the same number of turns as the secondary winding. Now add that in series with the secondary. Will work the same either way.

In the typical transformer, when we load the secondary, the primary inductance decreases, allowing more primary current to flow.

When we add the new core, new magnetic circuit, to the secondary, when we load it, the primary inductance actually increases, causing the primary current to be lower than idle current. 
Also, if we operate the primary at resonance, loading the secondary wont kill the oscillation. So we can tap that oscillation very efficiently to keep it going, as compared to driving a typical transformer as usual.

It is possible that this was Tesla's use for the "extra coil", to allow taking power from a secondary, without spoiling the resonant state of his primaries. 

As for a self increasing oscillation, Im just thinking that it may exist, from some things that Tito has said, and in Utkins document(below also), where it seemed to inform us of the need for a spark gap specifically for regulation. And it even explains some things about getting the self rising oscillation. (secret 1  Utkin pdf)

Ive had a lot less time to be on the bench. But im working on these ideas individually to get a feel for them, and hopefully when I put it all together, we see some good stuff.  ;]



Mags

Teeets!!!

Glad yer ok bud.      To pray, is the way.  ;]

As for the pat. Are you trying to get us to notice the rotary controller? Like the Ozone pat, there is also a rotary circuit controller.         

Mags 

Glad you are okay teets all the best with your health sir. Hopefully before god takes you you will share your knowledge with the world.

Yehey! Sir Teets is back!
            Am a bit worried of you not posting this past few weeks, i understand that you are so busy doing your works, and that asthma of yours is hindering you, but GOD is good all the time! he is our Jehova Rapah!


@Light2011,
            Thanks for your idea, feel free to join us here... I beleive you have many things in mind to share...

seems we now need to find where is Figure 7 

Figure 7?  What about 3, 4, 5, 6 and 8?   

Mags