Author Topic: new magnetic motor goes 2000 rpm without load 1000 rpm with load (Read 260334 times)

OffGrid rdnck · « **Reply #45 on:** April 30, 2007, 08:24:37 PM »

For all the money and time you've spent, and lets not forget all the energy wasted baking coils (and possibly melting the coating and making a short) for no good reason ( which causes global warming according to alarmists (which is all bunk)), you could have bought at least 2 windmaster 400 watt windmaster turbines that come complete with a plug in type grid tie inverter, and a built in charge contoller and powerfull charger. All you would have had to do is stick them up in the wind (not on top of your roof) and bought a few batteries for your battery bank.
You could have then bought a new large screen TV and sat down and enjoyed watching it with the free power the windmaster provides.

Or you could have built your own windmills from scratch like we do with the benefit of not having to make the same mistakes we did. and saved even more money.
Everything you needed to know can be found here:
http://www.scoraigwind.com/books/

kadora · « **Reply #46 on:** May 01, 2007, 08:47:24 AM »

Hi all
What about this generator which generates
electricity on rotor as well on as on stator.

magnacoaster · « **Reply #47 on:** May 01, 2007, 05:20:02 PM »

ok i have a question what is the speed this unit needs to run at ?

what is the mass weight ?

whats the voltage and amps it produces ?

whats the clog factor ?

do u have a website where i can see more about this ?

magnacoaster · « **Reply #48 on:** May 03, 2007, 02:50:42 AM »

ok i added a new video

http://www.youtube.com/watch?v=h9yW96g8ueo

http://www.youtube.com/magnacoastermotors

5 amps of pull still on the plus side

wahooooooooooooooooooooooooooooooooooooo

wattsup · « **Reply #49 on:** May 03, 2007, 02:38:45 PM »

@MC

Like the fact that you chucked the alternator and you added an inertia wheell. You should try and make some real measurements by putting your amp meter through the battery + and give the readings on what's going out of the battery - verus what is being loaded on your generator side.

I am doing tests along these lines also although a totally different approach.

Question, you are using the alternator recitifier, but are you also using the original capacitor in place, or just the rectifier? Also, where are you sending your rectifier ground.

hartiberlin · « **Reply #50 on:** May 03, 2007, 02:43:02 PM »

Quote from: magnacoaster on May 03, 2007, 02:50:42 AM

5 amps of pull still on the plus side

What do you mean exactly by this ?

Do you power all from one single 12 Volts car battery
and the battery is charged by 5 amps, so
the current from the battery is negative all in all,
so just only going back to the battery ?

Or where do you power your motor from ?

Many thanks.

Regards, Stefan.

magnacoaster · « **Reply #51 on:** May 03, 2007, 05:25:25 PM »

i added a air pump into the loop infromt of the meter that shows power out to the battery it can pull as high as 10 amps under load as i loaded it up i still got a positive feed to the battery as well as no slowdown in the motor

magnacoaster · « **Reply #52 on:** May 03, 2007, 05:33:42 PM »

You should try and make some real measurements by putting your amp meter through the battery + and give the readings on what's going out of the battery - verus what is being loaded on your generator side.

i have it setup so that it tells whats going in or out to the battery

battery - amp meter - motor + gen

Question, you are using the alternator recitifier, yes its mounted on the plywood

but are you also using the original capacitor
no we did not use this peice

Also, where are you sending your rectifier ground.

we have it isolated off the case with the wireing going to everything due to the em feilds you cannot use a case as ground as thre case its self will need to be grounded as to not charge up positive as the unit runs right now we have wheels on the case to isolate it off the floor as well as i have shoes on so i dont get a shock !

hartiberlin · « **Reply #53 on:** May 04, 2007, 12:16:15 AM »

magnacoaster,
I have problems understanding your setup:

1. Can you confirm, that you drive the motor with the same battery, that
your generator charges ?

2. Is the current coming out of the battery positive or negative ?
( So to speak , do you discharge or recharge the battery all the time,
when the unit runs ?)(if you just use one battery to power it all..and not 2 batteries)

Many thanks.
Stefan.

MeggerMan · « **Reply #54 on:** May 04, 2007, 12:53:37 AM »

Hi Magnacoaster,
Well done, I like the setup!
Are you saying there is 5 amps charge going back into the battery?
Could you find a smaller scale ammeter, say 10 Amps FSD as 60Amps leaves little resolution at the low end, or better still use a clamp ammeter.

Could you set it up as self running from a large 50v capacitor with no battery?
Just apply 12v supply to get it started.

Have you looked at using a solid state relay in place of the points or is the spark from the points critical to this working?

Rob

magnacoaster · « **Reply #55 on:** May 04, 2007, 02:13:34 AM »

ok i have provided a drawing below

hartiberlin · « **Reply #56 on:** May 04, 2007, 04:37:49 AM »

Hi magnacoaster,
so it seems you are just using one battery only ?

So does the 5 amps flow out of the battery or back into the battery ?

magnacoaster · « **Reply #57 on:** May 04, 2007, 06:53:35 AM »

we have the battery charged its taking 2 amps continus

the 5 amps we pulled was on the pump

MeggerMan · « **Reply #58 on:** May 04, 2007, 11:49:27 AM »

Hi MC,
Bit confusing the "pulling" and "taking", no indication of direction?
Can you put it in simple terms i.e.

Battery supply: 12Volts -2.0Amps (charging although the meter shows this as +2amps).
External load: water pump running at 12Volts +5.0 Amps

Rob

magnacoaster · « **Reply #59 on:** May 04, 2007, 11:39:05 PM »

Battery supply:
12Volts -2.0Amps (charging although the meter shows this as +2amps).+

External load:
air pump running at 12Volts +5.0 Amps

News:

User Menu

Author Topic: new magnetic motor goes 2000 rpm without load 1000 rpm with load (Read 260334 times)

OffGrid rdnck

Re: new magnetic motor goes 2000 rpm without load 1000 rpm with load

kadora

Re: new magnetic motor goes 2000 rpm without load 1000 rpm with load

magnacoaster

Re: new magnetic motor goes 2000 rpm without load 1000 rpm with load

magnacoaster

Re: new magnetic motor goes 2000 rpm without load 1000 rpm with load

wattsup

Re: new magnetic motor goes 2000 rpm without load 1000 rpm with load

hartiberlin

Re: new magnetic motor goes 2000 rpm without load 1000 rpm with load

magnacoaster

Re: new magnetic motor goes 2000 rpm without load 1000 rpm with load

magnacoaster

Re: new magnetic motor goes 2000 rpm without load 1000 rpm with load

hartiberlin

Re: new magnetic motor goes 2000 rpm without load 1000 rpm with load

MeggerMan

Re: new magnetic motor goes 2000 rpm without load 1000 rpm with load

magnacoaster

Re: new magnetic motor goes 2000 rpm without load 1000 rpm with load

hartiberlin

Re: new magnetic motor goes 2000 rpm without load 1000 rpm with load

magnacoaster

Re: new magnetic motor goes 2000 rpm without load 1000 rpm with load

MeggerMan

Re: new magnetic motor goes 2000 rpm without load 1000 rpm with load

magnacoaster

Re: new magnetic motor goes 2000 rpm without load 1000 rpm with load