Sphere Generator

What the Sphere generator is, is a generator that redirects several circuits of flux flow by the use of one flux switch.
The drawing is a very simple version of a sphere generator.

Now lets look at the generator like the earth with its magnetic pathing for one minute.  The strongest forces of the
magnetic field are at the north and south poles.  The magnetic flux then has several paths around the earth in order
to have the flux leaving one pole to come back to the other pole.  The first configuration of the sphere generator operates
like the magnetic field of the earth. 

Now if the generator stays in this one condition, then generator could not generate any electrical energy in it no
matter how many coils are in the generator.  This is because electrical energy can only be collected in this generator
with flux moving across the wires in the coils of the generator.

So how can I create this moving flux in a sphere generator?

This where I want you to look closely at the drawing of the water pump drawing below.
Now in the drawing there are several water pumps working at the same time, all the time.
So I see water pump running all the time moving water all the time as a permanent magnet
moving flux through it all the time.  The water coming in one side of the water pump
is the same as the water coming out of the pump.  In a permanent magnet, the flux coming
out of the permanent magnet is the same as the flux going into the permanent magnet.

So what the design of the sphere generator does is to take each of the routes from the
center of the generator on the top side to the bottom side with multiple secondary spheres.

How can this work?  Why won't the generator stay in the all of these secondary paths.?

This is where there needs to be a good understanding of how flux moves through different materials.
I use laminated transformer core metals in my design. 
Now it is important to know that magnetic flux will move both through flux material and also through air
as well, but there are conditions that the flux will move through air rather than the core material.

Each route or path of flux pathing from the top of the sphere to the bottom of the sphere is broken up
into permanent magnets followed by core material over and over again.  The reason for this is to support
a flux path from the the top of the sphere to the bottom of the sphere and then through the center of the
sphere.

At the same time each of the permanent magnets in the sphere have electromagnets with laminated cores
 in them parallel.  The core are not connected to the cores that are adjacent to the permanent magnets.
The reason for this is because we want this route to be secondary to the most desired flux flow route.

Now there can be several of these routes of assemblies can be connected together into a sphere so that
each of the loops can be connected together and move in one laminated core material through the center
of the sphere.  Now wire can be wrapped around this core material in order to produce an electromagnet
in the core of this generator.

With no power to the electromagnet, the flux from each magnet will flow from it's pole through the
laminated core into the next magnet over and over again through the full loop.  This is because during
This condition, the flux finds a better path moving through one large circle than to move flux through
the coils parallel to the permanent magnets. 

Now when the one electromagnet is turned on to  move a flux in an opposite direction than the flux
flow of the zero electromagnet condition changes everything.  The output flux of the electromagnet
will come out and go through the air around itself into the other side of itself.  This closes off the
flux flow in that large flux route.  So what happens now to all those magnets in the generator?

As you know the permanent magnets will not stop working, but will reroute the flux they have in them.

Now where will it go?

Now since the flux out of a permanent magnet is equal to the flux into it,  the flux moves to the next best route.
The first permanent magnets next to the flux switch, will route its flux through the parallel coils to the permanent
magnet.  Now since the output flux is equal to the input flux, the permanent magnet next in line in the path now
moves its flux path around itself.  This is the chain reaction of the flux switching that occurs in this generator.
This chain reaction not only occurs through the whole loop of the path of permanent magnets and laminated
core materials, but this happens with all of the paths around the full sphere assembly.

The result of this generator is one switch operating at a 50% duty cycle can reroute the flux paths of several
permanent magnets in the generator.

Now the important thing to know about power generation in an electrical generator is that you can not generate
electrical energy from constant flux flow.  You have to have changing flux flow in order to do that,
The great thing about this generator is that it provides several places of flux movement.  By tapping into each
place in the generator where there is a change in the flux movement, is an opportunity to produce electricity.

This means one flux switch operating at a 50% duty cycle can produce electrical energy from several output coils.

Now the next question is, If this new technology from 2021 be used in motor assemblies as well?
That answer is yes.  I have put those designs into my latest book so on Amazon and many other places as well.
I go into greater detail on the generator and motor designs in the book.
I want people to freely use my designs so that is why I have published them.

We can build a better world if we all work together to bring new technology into every home.

Jay Lunke

Lunkster

Thanks lunkster.

Once again you have presented us with an interesting concept.

I hope to be, in the sometime future, moving into looking at
these kinds of designs.

best wishes
    floor