Void
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #21806 on: March 01, 2020, 10:11:02 PM »
Quote from: Ntambi on January 14, 2020, 10:42:58 PM
Some Food for the brain
The circuit below is from some of the first videos of Tungus before he changed his name to Akula..
Im gonna be posting to show you the similarities between Akula, Tariel Kapanadze, Weasley, SR193, Tiger2007 and Michel Meyer...
the connection is that all these devices utilise nuclear magnetic resonance of ferromagnetic materials to produce excess energy...
Now from the circuit:
Lets take a look at object 1 and 3 which are diode bridges... Diode bridge 1 converts the high frequency AC current from the output back to DC into the system (loop) through inverter 2... then the inverter 2 converts the DC current back to AC but this time at 50Hz, its then connected to diode bridge 3 which converts AC back to DC to power the driver circuit 5...
if you read the above statement you can easily tell that it makes no sense, why not connect the DC from the output directly to driver circuit 5 other than converting it to AC then back to DC to power the driver..
Hello Ntambi. Welcome to the forum.
I would agree that the principle behind Daly, Akula, and Ruslan devices all appears to be the same principle,
as the setups are all very similar, and Ruslan of course copied Akula closely, assuming any or all of those circuits
were/are legit.
However, I am not convinced that what was shown in the 'Lithuania experiment' was the same,
but, yes, the underlying principle may possibly be the same in that setup as well.
Kapanadze remains a mystery so far, as he has kept some key details about his circuits hidden.
It is possible that what Kapanadze is doing is using the same principle as well, however.
I think you may be mistaken about the 'inverter' in Akula's early 'self-runner' circuit setups.
I believe that is an AC to DC power supply, not an inverter. Akula was converting
the high voltage AC output from his output coil to a lower DC voltage such as 12V or 24V,
and using that lower DC voltage to feedback back to the input and power his PWM driver. Yes, he may have a
fullwave bridge rectifier before the power supply, but the step down AC to DC power supply apparently still works
even when fed with say around 220V DC (or pulsating DC) rather than 220V AC.
Hello to everyone else as well!
All the best...
https://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg543462/#msg543462Void
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #21807 on: March 01, 2020, 10:23:40 PM »
Quote from: NickZ on March 01, 2020, 02:26:32 PM
Well guys, most of the real builders have left this thread, or are waiting for something that really WORKS.
What is this board coming to then? NMR... Here we go again... burning shit up, instead of finding the REAL solution, tapping ambient energy. Not harmful, non polluting, etz...
Can we get back to that, instead? If Verpies does not want to test his device, maybe itsu can do it? Or, someone that can take input to output measurements.
But, what is the point of bringing up a test of a device on this open source thread, that won't be disclosed? That does not sound right to me.
Hi Nick. I might be willing to run such a device through testing on my bench and
post all the test results here or on Youtube, depending on the conditions of the arrangement made, but it
looks like Ntambi wants to keep it private.
Ntambi:
In such a case, Ntambi, maybe you can post up a private video of your test setup with any measurements
you are making, on Youtube or on your Google drive or similar, and PM or email me the link, and I could give an analysis
of what I see in the video. That way you don't have to send out your device to anyone. BTW, I am not at all convinced that
the Thane Heins style transformer arrangement is doing anything unusual at all, and from what I have seen,
Thane Heins seems to have come to the same realization at some point a number of years ago. I believe what Thane may have
been seeing with his transformer was actually just a leakage inductance effect.
Ntambi, if your test setup relies on the Thane Heins transformer, then I have doubts about your test setup.
Have you managed to get your test setup self sustaining (self-looped), or are you doing measurements
to conclude a COP >1 in your test setup?
All the best...
void
https://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg543463/#msg543463------------------------
Void
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #21816 on: March 02, 2020, 06:08:26 PM »
Quote from: DavidWolff on March 02, 2020, 09:41:09 AM
And I have an OFF TOPIC question for Void JB had a circuit with a two capacitor parallel charge and a series discharge into a lead acid battery.
Witch JB seriously promoted Question did you prove that circuit?
I cannot post the schematic as it is copy write.
Dave
Hi Dave. I have tested several different variations of such Bedini arrangements, but the problem
right from the start with such circuit arrangements is they of course return less energy back to the battery
than is being expended from the battery to run the circuitry. Thomas Bearden proposed that pulsing the battery is what
is drawing in extra energy into the system inside the battery via 'asymmetric regauging', I think is the term Bearden used.
However, I have as yet not been able to see indications that such 'asymmetric regauging' is occurring in a pulsed lead acid battery
in my own experiments. That's why I have been focusing on the battery 'back popping' approach in the last while.
All the best...
https://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg543488/#msg543488-------------------------
GeoFusion
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #21846 on: April 18, 2020, 04:22:02 AM »
AG
"so what's the missing link we are ignoring ?"
What many didn't mention much, B.E.M.F. energy
Is the missing link.
Do not focus on the conventional ways of getting energy out....
** edited post
https://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg544868/#msg544868GeoFusion
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #21855 on: April 18, 2020, 07:01:37 PM »
Quote from: NickZ on April 18, 2020, 04:40:05 AM
Hi Geo: Welcome back. How goes it? Long time no hear... NickZ
Hi Nick,
Yes, busy as always with many things that are important.
I'm just here to give hints that will help.
To understand the system is to focus on the Collapsing field part and using a HV swing right when that happens.
this is what gives it the multiplication method. resonances are used to keep in tune for the system to work and the amount that
you want to receive corresponding to the LC configs. Sync is needed as well otherwise it wont work.
then you have to see when kacher needs to be fired on the correct moment when Mosfet of pushpull is off.
The simple kacher has to be turned off completely by a switch, ( MOSFET) for a brief pulse when the collapse of field is
happening on the grenade. You can add an extra FET that will control the simple kacher negative terminal on or off in fast.
tricky part is that, to sync that specific part.
As what Ruslan said long back or Akula, the Tesla coil/ Kacher is what is doing all the massive output work after.
Make sure you only tap from out put after diode bridge. not befor! otherwise resonance is broken.
Bemf is what this output is, I have seen to much but had to say it.
Important EDITED **
** Nick, I reflected on my old videos where in 2016 was a year I almost had it but it was unstable
Yet it performed as Ruslan did but was limited power yet it did not effect the input at all when changing output
load. In those days I had no idea precisely what was going on but was doing my best to understand, but now I do.
The BEMF was present that day at the output , this is why it did not effect the input.
If there were another tesla coil circuit that could handle higher voltages input such as 60VDC would have made this output greater that day without increasing the input.
this is the video from 2016
The output is not affected by touching the antenna that also shows that the operation is different as I am stating.
https://www.youtube.com/watch?v=1weV296sjHU&t=Now I know what to do
, It has taken me 4 years to figure it out since that day.
Now I know what to do
, It has taken me 4 years to figure it out since that day.
Now I know what to do
, It has taken me 4 years to figure it out since that day.
Now I know what to do
, It has taken me 4 years to figure it out since that day.
Quote from: Raycathode on April 18, 2020, 09:50:48 AM
No look again at Nelsons circuit he kindly published he is using that !
Want to try again ?
It does not matter of his circuit now, yet he had some success but we are working on the Akula/Ruslan/Dniester Device here.
Focus on that.
I'm simply helping giving hints and my findings over the period of times.
Cheers
https://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg544887/#msg544887-------------------------------------
GeoFusion
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #21857 on: April 18, 2020, 09:24:43 PM »
Quote from: DavidWolff on April 18, 2020, 09:05:48 PM
Geo! i'm not disputing you have something working BUT!
this was Wesleys Lithuwanian experiment I don't have one or Ruslans device
but this device worked.
Even Delomorto talkes about it on his wersleys thread
It makes sence Ruslans does not!
Hi Dave,
Yes I am aware of this device and have spoken to T-1000 about it many times.
The way this is making energy is completely different from the Akula/Ruslan Devices.
STAAR Yoke device is doing Ferrite Transmutation energy output. this leads to nasty Radiation from the extra material
they had inside the composite of the Ferrite material. those two frequencies Exited it and release it and within certain
resonance. Not sure if it was mixed of Barium inside the Ferrite.
**On thing Ruslan did not talk about nor Akula is how this energy comes about to existance.
that is where they are bastards for a long time... my time invested to see and experiment what it is all about
came to an realisation.
By my findings it is Bemf harvesting and havign resonance all over to keep the balance.
The collapsing field energy and having a brief HV HF pulse right after is what accelerated the output.
This is the type of output when loading it, will not have effect on input. Simple as that.
Ruslan's lastest videos back then for sure did show he using other ways how to
but it is the same outcome and method he is using but difference devices to get it.
Again, STAAR device is comepletely different, Unless you are trying to to nuclear resonance on copper
which is not the thing here right now.
Ruslan did not infact never say what is happening at output but at the video I just posted of my experiment in 2016
RUSLAN did msg me and told me I am close to figuring things out but I had still no clue back then.
Right now, I have.
Right now, I have.
Right now, I have.
Right now, I have.
Right now, I have.
Right now, I have.
https://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg544890/#msg544890
