I don't think there's much more to the schematic than this. "Its so simple you will laugh".

I trying to grow some legs on it. Get a bit more expert opinion. Iron out the wrinkles. Lets see what happens over there.

I forgot to mention a few things:-

1. The circuit is similar to a single phase electric motor:-https://www.youtube.com/watch?v=pbg_PF6MTwY&t=326s
2. Why rectified AC rather than AC?
3. How to stop the core from saturating?

To my knowledge the circuit hasn't been tested.

Thank you Tomd 
I still seeing the same in Tesla patent 382,282 check it...

it will be observed that at a given point of time the coil G is in its neutral position and is generating little or no current, while the other coil, G', is in a position where it exerts its maximum effect. Assuming coil G to be connected in circuit with coils B B of the converter, and coil G' with coils B' B', it is evident that the poles of the ring A will be determined by coils B' B' alone; but as the armature of the generator revolves, coil G develops more current and coil G' less until G reaches its maximum and G' its neutral position. The obvious result will be to shift the poles of the ring A through one quarter of its periphery. The movement of the coils through the next quarter of a turn, during which coil G' enters a field of opposite polarity and generates a current of opposite direction and increasing strength, while coil G is passing from its maximum to its neutral position, generates a current of decreasing strength and same direction as before, and causes a further shifting of the poles through the second quarter of the ring. The second half-revolution will obviously be a repetition of the same action. By the shifting of the poles of the ring A a power-dynamic inductive effect on the coils C C' is produced. Besides the currents generated in the secondary coils by dynamo-magnetic induction, other currents will be set up in the same coils in consequence of any variations in the intensity of the poles in the ring A.

UNTIL NOW I HAVE NOT OBTAIN GOOD RESULTS, ONLY A VERY, VERY HOT CORE(BOTH OF THEM CORE)

That's because it's dc (rectified ac). I was hoping someone could provide a solution to this. If you try it without the bridge you shouldn't get the heating problem. However Fernandez makes a point that you must use rectified AC.
I'm not sure how to figure out the correct size capacitor. Trial and error maybe?

"BOTH OF THEM CORE" - There is only one core. Have a look at his core with the C clamp and soft iron rod.

1. Hey Leon, nothing to frown about, those hot cores identifies eddy currents, those currents don't create themselves. Keep going I think you are doing GREAT!!! Very nice to see people fishing for themselves.

2. Regarding rectified AC ..... don't get caught up in the word "must" sharp rising and falling DC pulses can look like rectified AC.

3. You can create the same result (magnetic field) with an Arduino (or any other programmable control), this gives you the added luxury of playing with different timings. In the capacitor circuit the it is the size of the cap that creates the delay. This can also be done with programming.
 
4. When we started, we researched B&L's device exclusively. It was like trying to make the perfect partner, and that is one that is good on the inside and good on the outside.

5. Yes Barb&Leal left some items out of their patent,(i dont think much) but they all do. Like everybody does we also thought it must be super complex, this type of thinking prevented simple workable ideas. One day, while having some beers, we simplified the problem down to two very simple parts. I think the idea came from talking about how water is made. It was stated..

"It's really only two parts from different sources but when combined they create a liquid" .....<-----outside the box thinking

Someone then said

"You know...... we only need a magnetic field and a potential because isn't that what happens in a generator? "

 

6.  So, there is a patent application out there that nobody talks about. Its hard to find maybe? Regardless it really helped us and pointed in the right direction. It's not the Holy Grail but find it and review it completely. Look for this: Application# DE200610054568  we poured over it MANY years ago.

I don't post much, time is a factor and I am very busy. I have worked for a global energy giant and now have a much more demanding job. With that said I always find time for the bench because that is where the magic will always happen. These forums have a lot of negative noise and can be counter-productive. You really need to love what your doing and not let it be stressful.

Let me say one more thing, there are thousands of farmers in this world. There are also thousands of amateur farmers in this world. With all these people that know how to grow and produce food why do people in this world still go to bed starving.
I wrote that because nobody should think they are going to be a hero and save the world. That tpye of thinking is scary.

Fernandez
Thank you for feedback and suggestion, those words encourages me; I’ll still try my best, I don’t believe in everybody, because like you said this world is full of people that are making their life and all around much harder, but I believe in God and some good people around…
OK, let me see if I can get something better this time!!!

1. Hey Leon, nothing to frown about, those hot cores identifies eddy currents, those currents don't create themselves. Keep going I think you are doing GREAT!!! Very nice to see people fishing for themselves.

2. Regarding rectified AC ..... don't get caught up in the word "must" sharp rising and falling DC pulses can look like rectified AC.

3. You can create the same result (magnetic field) with an Arduino (or any other programmable control), this gives you the added luxury of playing with different timings. In the capacitor circuit the it is the size of the cap that creates the delay. This can also be done with programming.
 
4. When we started, we researched B&L's device exclusively. It was like trying to make the perfect partner, and that is one that is good on the inside and good on the outside.

5. Yes Barb&Leal left some items out of their patent,(i dont think much) but they all do. Like everybody does we also thought it must be super complex, this type of thinking prevented simple workable ideas. One day, while having some beers, we simplified the problem down to two very simple parts. I think the idea came from talking about how water is made. It was stated..

Quote

"It's really only two parts from different sources but when combined they create a liquid" .....<-----outside the box thinking



Someone then said

Quote

"You know...... we only need a magnetic field and a potential because isn't that what happens in a generator? "


 

6.  So, there is a patent application out there that nobody talks about. Its hard to find maybe? Regardless it really helped us and pointed in the right direction. It's not the Holy Grail but find it and review it completely. Look for this: Application# DE200610054568  we poured over it MANY years ago.

I don't post much, time is a factor and I am very busy. I have worked for a global energy giant and now have a much more demanding job. With that said I always find time for the bench because that is where the magic will always happen. These forums have a lot of negative noise and can be counter-productive. You really need to love what your doing and not let it be stressful.

Let me say one more thing, there are thousands of farmers in this world. There are also thousands of amateur farmers in this world. With all these people that know how to grow and produce food why do people in this world still go to bed starving.
I wrote that because nobody should think they are going to be a hero and save the world. That tpye of thinking is scary.

Hey Forest

Do you have some input that enlightens a little more?
Yourself said "we should be doing now great change"