Your work is and will forever remain an abomination, and you are one to talk, all you do is insult "others" work, hypocrite. I just say what others won't about yours and the resident plagiarist, copy paste junkie.

You can't read......Not no, Hell no....




I have no interest in joining your boy band....HELL NO.  The two of you can work that out on your own.

And that is exactly what we are doing.
Before that can be done,we all must understand places where Lenz can hide.
I showed a good example of that in Jim !tha man! Murray's dynaflux generator.
You presented Jims work as being advanced in this area,and i showed that it is in actual fact,way behind in this area. In Jims dynaflux generator,Lenz hides within produced eddy currents,proven using Jims own numbers in his video.

You (like Jim) thought that the load(two bulbs) placed on the generator,placed no load on the prime mover,when in fact,the prime mover was heavily loaded before a load was even pulled from the generator.

These are the tricks people here can learn to watch for,and also shows where !Lenz! can be hiding.

The only reason you think this thread is not on track,is because it is not going the way you want it to go--that being,your way.

But hang in there Erfinder,you might just learn a thing or two,from the guys that build abominations 


Brad

Erfinder,

I am really surprised at your behavior.  You may recall we have had a couple of conversations on Skype.  I thought you were a gentleman.  Now I see I was very wrong.  It appears you are in the same category as Synchro 1.  When someone shows you that you are mistaken instead of trying to answer from a technical viewpoint you go on the attack with name calling and vulgarity.  Shame on you.  Acting like a 10 year old bully instead of a grownup.  I will no longer waste any time reading anything you post.

Carroll

Oye Vey
Isn't there a football game on  ...?

Yeesh

perhaps a little quiet time Beating the cat or something ??

Tweeze a few nose hairs maybe ?

shooting holes in the boat is never a good idea , we need all the hands we can get around here

Hi Brad,


At the moment it is all in my head. So the first model is just to test the parameters. As has been pointed out, the material from Energetic, "the final, final, final, secret of free energy" does not say much. Aaron is touting the Scotch Yoke but in this case it suffers from the exact same faults as the crankshaft. Namely the pull in force of a solenoid is all in the final moment of closure. The Scotch Yoke and the crank shaft are at the 12:00 o'clock and 6:00 o'clock position... meaning no transfer of force is possible at that time. To solve this problem he has the timing set to be off !!! thus defeating the maximum force. He admits that his build is "not very powerful"  and didn't even show it running.


So to get a better force transfer I am going with one way clutches, and just two solenoids. Just working on the switching now as I quit for the day.  To show what I mean, in the  graphic below if you pulse the solenoid too soon it will be very weak. One must pulse up on the curve. The right hand side of the graphic is with the plunger out, as it is drawn in it peaks on the left.


Thanks, Ron

One way clutches(sprag clutch) and solenoids sounds familiar 

Here is a little engine design i came up with some years back that uses these very parts.

https://www.youtube.com/watch?v=Z4VJG8-9izQ

I designed it so as maximum force is always placed on the crank shaft,as the cranks big end journal is always at 90* when the solenoid fired,unlike a normal ICE,where the big end journal would be at(close to) TDC when the gases ignited,and all the force would be on the main bearings of the crank.

Oh,and a short video of it running on free energy lol.

 https://www.youtube.com/watch?v=4wITJVy0rPE


Brad