GDPR and DSGVO law

Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding.
Amazon Warehouse Deals ! Now even more Deep Discounts ! Check out these great prices on slightly used or just opened once only items.I always buy my gadgets via these great Warehouse deals ! Highly recommended ! Many thanks for supporting OverUnity.com this way.

User Menu

Plug Heater

Powerbox

Smartbox

3D Solar

3D Solar Panels

DC2DC converter

Micro JouleThief

FireMatch

FireMatch

CCKnife

CCKnife

CCTool

CCTool

Magpi Magazine

Magpi Magazine Free Rasberry Pi Magazine

Battery Recondition

Battery Recondition

Arduino

Ultracaps

YT Subscribe

Gravity Machines

Tesla-Ebook

Magnet Secrets

Lindemann Video

Navigation

Products

Products

WaterMotor kit

Statistics


  • *Total Posts: 503254
  • *Total Topics: 15043
  • *Online Today: 44
  • *Most Online: 103
(December 19, 2006, 11:27:19 PM)
  • *Users: 2
  • *Guests: 12
  • *Total: 14

Author Topic: high voltage  (Read 10781 times)

Offline raburgeson

  • Hero Member
  • *****
  • Posts: 705
high voltage
« on: April 16, 2005, 01:13:23 PM »
I ran into a snag on my low voltage source and am going to try a large battery charger with a good
boost on it.Flybacks are to weak.We have to figure out a cheap way to get above 300 KV, that of course
doesn't wiegh to much.I'm trying to run ignition coils in parallel and have had some limited success but
the isolation caps between the coils have been arcing between the terminals.Maybe if I make cathodes
and anodes half ellipical  shaped to reduce arcing at the edges and also it wouild move to temrinals farther
apart.(just becase of the shape of the plates)  What do you guys think?

Things are looking up in some other areas though I got a new 8.5 hp motor from Northwestern,
and a 100 amp alternator off an old school bus at the junk yard - that was a good find. I,ve
heard that firetrucks have a better alternator but none of the scrap yards here have one, go
figure.

Free Energy | searching for free energy and discussing free energy

high voltage
« on: April 16, 2005, 01:13:23 PM »

Offline betajim

  • Newbie
  • *
  • Posts: 26
Re: high voltage
« Reply #1 on: April 17, 2005, 05:48:05 PM »
Hi,

Achieving 300 kV is going to be hard, especially with ignition coils. There are two ways I
would go to get that high a voltage: 1) use a Van de Graff type generator, this has the
advantage of supplying a DC current. 2) find some high voltage step-up transformers of
the type used in high voltage power transmission, the down side is they won't be cheap
even if they could be found surplus.

Are looking to generate 300kV AC or DC?

Offline Dinorben

  • Newbie
  • *
  • Posts: 5
Re: high voltage
« Reply #2 on: April 18, 2005, 11:43:20 AM »
I'm no EHT expert but I wonder if a long voltage doubler circuit might be a better option than trying to stack coils?

But either way, with 300kV I guess the  main problem is going to be insulation - a 20 kV discharge will arc about 10 mm through dry air, but the same discharge can travel over 20mm along a clean surface, and at your target voltage I guess you have to multiply those distances by 15 :( 

Insulating materials perform much better than  air - I wonder if keeping the entire unit potted in wax would help? Even so, at 300kV you might have to resort to using porcelain or even glass insulation immediately adjacent to the conductors.

Dinorben

Free Energy | searching for free energy and discussing free energy

Re: high voltage
« Reply #2 on: April 18, 2005, 11:43:20 AM »
Sponsored links:




Offline raburgeson

  • Hero Member
  • *****
  • Posts: 705
Re: high voltage
« Reply #3 on: April 18, 2005, 12:11:29 PM »
Insulation is a big problem,and I've had companies sell me supposably new materials that are
high quality that has turned out to be recycled bull feeces. I have learned how to test
insulation by throwing some into the microwave and watch for sparks , if it's recycled crap
you will see sparks.

Offline raburgeson

  • Hero Member
  • *****
  • Posts: 705
Re: high voltage
« Reply #4 on: April 18, 2005, 12:46:21 PM »
Midsun and Sylguard seem to be the best 2 sorry hit the wroung  key and sent post to
early.

Free Energy | searching for free energy and discussing free energy

Re: high voltage
« Reply #4 on: April 18, 2005, 12:46:21 PM »
Sponsored links:




Offline Paul-R

  • without_ads
  • Hero Member
  • *****
  • Posts: 1792
Re: high voltage
« Reply #5 on: April 19, 2005, 05:50:49 PM »
Here is a strange technology:
http://www.optimalenergysystems.com/PPC%202003%20Paper.pdf
It seems to be rotating magnets - high speed - relatively high volts
storing a large high voltage charge in some way - a sort of Faraday Disc
gone wrong. Does it have a use?

Paul

Offline raburgeson

  • Hero Member
  • *****
  • Posts: 705
Re: high voltage
« Reply #6 on: April 19, 2005, 06:41:18 PM »
It's useful but to heavy for lifters.

Free Energy | searching for free energy and discussing free energy

Re: high voltage
« Reply #6 on: April 19, 2005, 06:41:18 PM »
Sponsored links:




 

OneLink