Hi NickZ,

Thanks for the "priceless observation" regarding your testing (an independant source from a learned,
experienced hands-on, experimenter). Appreciated here more than you know!

Could you please provide a link to the video showing this effect (your last video) so I'm sure we're on
the same page, so to speak. TIA.

Almost there - you can just "feel" it! 

SL

 NickZ - I know you have been told to try a thousand things so I hesitate to suggest anything else -

But, just from your video - you probably have noticed that the "base circuit - everything without the Katcher - is oscillating;
appears to be a somewhat random very low frequency (likely involves a large capacitor and/or large inductor [you have both
in the circuit]). Almost a "fill and then dump" type thing.

Since the circuit is high Q (resonant), this is not uncommon; and the [positive] feedback causing the oscillation might be hard
to isolate. You don't need the HV on to troubleshoot this - take a capacitor .1uF, 1uF, 10uF, or so, and ground one side then probe through
the circuit [methodically] until you find the cause - and the circuit becomes stable.

Could even be the 60/50Hz in your lab - turn off everything not required (unplug Katcher PS).

Watch the scope top trace before induction circuit turn on - then at 02:52 through 03:00 (Katcher turn on).

The noise seen on the top trace appears to be "pulse bounce" but that's just a guess from the video. Play the video
from 02:50 to 03:00 at 25% and it's somewhat noticeable. {VLC player works good for this, also set two limits and loop}

The noise also takes a while to build in amplitude as seen in slow motion.

Thats my first pass WAG (Wild Ass Guess) anyway! This is an aside from the Stable Processor thats under development however.

Will look at it a bit more when I have more time... Hey, not much, but its free!  SL

 Nick,

Good - stabilize the "inductor part" by tuning with the feed back power supply connected.

Your Katcher frequency might be a bit low - with the inductor at 18.000KHz - try to set the Katcher to around 1.800MHz
(10x inductor circuit frequency - or some exact frequency multiple).

Phase is important here - so you will have to play with that (the ferrite with coils connecting the TT to the Antenna).
 
As is the HV - which sets the velocity of propogation - which is set by the primary of the TT/Katcher. Slowly adjust the
TT primary voltage level [sets the HV velocity of electrons] and the pulse frequency [sets the interaction "electron
bunching" with the inductor - needed to achieve more output]. These pulses are applied optimally at about the 18KHz TDC.

Anyway, that's what seemed to work here... Other than that, well IDK?

This schematic might help (01 Ruslan - Absolute):
https://www.overunityresearch.com/index.php?topic=4154.msg96060#msg96060

SL

   Yes well, I spent a bit of years working on all this. Such as tuning my Kacher to different frequencies, and get the best result anywhere from 900khz to 1.2mhz. And not higher.
Of course you have to tune with the feed back circuit connected. Which changes things  drastically
  You will never figure this type of device by speculating. Once you build it, then you can speculate on how you think that it should work.
Itsu followed the instructions to a T, yet, it won't work as planned.

  NickZ

NickZ,

Sorry you guys were not able to make it function as required.

We did, and so did a lot of others, as you know.

Just trying to present some information as to how it works; but that
seems not enough - well so be it.

Good Luck... have a nice day!

SL

 
I have not followed OU or OUR stuff at all really - never found much that was very useful.
 Posting on occasion in an effort to distribute information that might be useful but that's it.
A couple of RU forms were far more informative IMHO.

My proof (if that's what you want to classify it as) would be no different than Ruslans.
A shakey video and a few scope shots with lit bulbs or a heater. What else is there?

Here's two videos from amongst the hundreds on the web - that's all I can offer.

You might have to face the fact that not everyone is skilled in the art of electronic/RF design!
There is no How To Cookbook... 

 https://www.youtube.com/watch?v=s1ves5ukyVI

https://www.youtube.com/watch?v=zbfsdamSbXw

Plus, this is one of the hardest forums to post on - formatting is impossible and attachments are limited.

Then add the bickering and trolls, so, quite frankly its a big pain - therefore, you'll have to help yourself.

 SL:   Ok, that's what I thought.  What more? Well, they can pull the plug from the wall, show it self running with NO  input.That's what more.  Like Akula, Ruslan, Adrian Gustav, Stalker, and Kapanadze have shown doing so.
    NickZ

    P.S. Just wondering about your previous posts about you not finding any truth to real OU, nor self running devices. Really? Did you know where to look. No?
   

Solarlab
Or !!
Or you can invite some of the champions here who toil for years
And still do In Holcomb topic and elsewhere!
To visit your lab or ?
Teach!!


Ariovaldo
UFO
Mags
Ben4Kzep
Ciftfa ( not far away)
Etc etc etc
Tommy Reed spends months at a time working there too


Members In Florida!!
??
You want to change the world.?
“BE THAT CHANGE “”
Teach

By the way, I'm in Florida.