Author Topic: Kapanadze Cousin - DALLY FREE ENERGY (Read 11826809 times)

kolbacict · « **Reply #23265 on:** February 13, 2022, 04:27:15 PM »

https://www.youtube.com/watch?v=ZDFEevnkuq0
Yes. I did it too. Even better if the ground circuit is a series resonant circuit.
No miracles here. All according to physics.

AlienGrey · « **Reply #23266 on:** February 15, 2022, 01:00:29 AM »

Magpwr, thanks for your circuit diagram, I didn’t use the Akula circuit in a project I just played with the thing on the bench,
So many thanks for that. those mos fets were to slow for 2 mhz response, my guess was Ruslan was playing with us.

in the end i used a 74hc132 the 74hc00 in many circuits needs different design circuits.

It might be of interest, that member Vasic41 published a drawing mod to a TL494 with an axtra pot in the series with the 22k freq trim pot a 3k or 5k for easy tune, he says it's needed for tuning in fish wave , but I have never been able to attain such a phenomena, but it would explain a lot.

I would have given a hyper link but i can no longer find Vasics pdf on OUR.

Sil

Dove · « **Reply #23267 on:** February 15, 2022, 09:17:09 AM »

Quote from: AlienGrey on December 21, 2021, 01:06:01 PM

if you look at page 1532 Ruslan is holding up the very circuit *you used almost 2/3 a page discrediting me over this! ) But Akula is talking about Phase Shift on this circuit, So move on anf learn. Have a nice day!

This is a very interesting one from Akula, did you notice the picture on the right bottom, looks to me like a microwave resonator,?

is this not a cryptic message, Kapanadze always referred to the resonator inside, strange.

magpwr · « **Reply #23268 on:** February 15, 2022, 02:02:05 PM »

Quote from: AlienGrey on February 15, 2022, 01:00:29 AM

Magpwr, thanks for your circuit diagram, I didn’t use the Akula circuit in a project I just played with the thing on the bench,
So many thanks for that. those mos fets were to slow for 2 mhz response, my guess was Ruslan was playing with us.

in the end i used a 74hc132 the 74hc00 in many circuits needs different design circuits.

It might be of interest, that member Vasic41 published a drawing mod to a TL494 with an axtra pot in the series with the 22k freq trim pot a 3k or 5k for easy tune, he says it's needed for tuning in fish wave , but I have never been able to attain such a phenomena, but it would explain a lot.

I would have given a hyper link but i can no longer find Vasics pdf on OUR.

Sil

hi AlienGrey,
The Akula circuit is merely a interrupter self tune by LM393N with the assistance of simple current pickup winding on toroid regardless of tesla coil frequency.
Anyway it's your experiment i won't stop you.
The pwm even it work for the moment would eventually drift in frequency as various components heats up.Long story short it will fail after prolong period of operation,but definitely good enough for short duration demo.

---------------------

AlienGrey · « **Reply #23269 on:** February 15, 2022, 10:09:44 PM »

Hi Magpwr, yes your right about the comparator add on section, What i'm testing for here is standing waves in the catcher coil winding Vasiuc41 describes in his PDF over on OUR tech publications,

Have you managed tried to achieve standing waves within your catcher circuit or is it BS, Some time ago Delomorto showed a video with a catcher wound on a pvc pipe with a split copper water pipe section in side the pvc pipe and used an old tuning capacitor for maximum spark thus lighting up a large 240 Volt bulb in series with the earth feed.

Sil

Dove · « **Reply #23270 on:** February 16, 2022, 12:45:48 PM »

100% correct.
I've been watching these threads for years I maybe mistaken but for about 15 years and have always kept quiet, just observed, I know it shows me as a newbie, but that's not correct its because my mailing address and name has changed a few times because of work.
Delamorto showed that if you place the copper plate inside the coil and the ferrite inside the copper plate there was a huge difference in the output, that's why i am trying to get you guys to look at ferrite on the inside of the copper plate as a 50Hz resonator.
Correct me if i am wrong but what was it that CosmoLV said when Delamorto first showed this on his video, The guy almost had a hissy fit and said were getting to close to the real thing.
Do me a favour look up copper ferrite resonators, there are quite some surprises to be learned.
Another observation that i made with a tesla coil I built years ago, ill find the photos and post them for you guys, the coil was built in the normal fashion, except i did not do the conventional thing at the doughnut, there i placed a flat circular disc covered in copper foil, then i built two small coils on top of that connected to the flat plate, and a copper ball on top with a short delay line tube to the ball, well guess what the voltage and current phases lined up there was no lag or lead in the power factor.
Something else i realised years later was that at the flat plate the brush was not moving away from the plate but rather moving toward it almost as if the energy was being drawn in.
These are all things that can help I hope not trying to move you guys away from the topic at hand.
Best Regards
Chris

magpwr · « **Reply #23271 on:** February 16, 2022, 02:50:32 PM »

Quote from: AlienGrey on February 15, 2022, 10:09:44 PM

Hi Magpwr, yes your right about the comparator add on section, What i'm testing for here is standing waves in the catcher coil winding Vasiuc41 describes in his PDF over on OUR tech publications,

Have you managed tried to achieve standing waves within your catcher circuit or is it BS, Some time ago Delomorto showed a video with a catcher wound on a pvc pipe with a split copper water pipe section in side the pvc pipe and used an old tuning capacitor for maximum spark thus lighting up a large 240 Volt bulb in series with the earth feed.

Sil

hi AlienGrey,
Regarding Tesla coil provided if you are comparing between various tesla coil design with respect to frequency.
You may by now noticed that Tesla coil of certain lower frequency produce "blue plama" and "higher frequency" eg:HFSSTC produce hot orange plasma even at a lower voltage source <20volts.
This is the one we should be interested in where even mains bulb can be made to glow easily at low voltage even merely by touching tip of bulb to the Tesla coil.
If you own a high frequency current probe or little cheaper alternative eg:mini RF AMP meter which is connected in series with bulb to Earth.
Then you will know at which Tesla coil frequency would produce a better result.You may already know the AM ferrite rod is good up to 10Mhz but more realistically around 8Mhz or lower. used in Akula kapanadze demo,before the Antenna winding as example.

------------------------------
Lets see what your findings are base on experimental test.

AlienGrey · « **Reply #23272 on:** February 24, 2022, 02:05:21 PM »

Quote from: Dove on February 16, 2022, 12:45:48 PM

100% correct.
I've been watching these threads for years I maybe mistaken but for about 15 years and have always kept quiet, just observed, I know it shows me as a newbie, but that's not correct its because my mailing address and name has changed a few times because of work.
Delamorto showed that if you place the copper plate inside the coil and the ferrite inside the copper plate there was a huge difference in the output, that's why i am trying to get you guys to look at ferrite on the inside of the copper plate as a 50Hz resonator.
Correct me if i am wrong but what was it that CosmoLV said when Delamorto first showed this on his video, The guy almost had a hissy fit and said were getting to close to the real thing.
Do me a favour look up copper ferrite resonators, there are quite some surprises to be learned.
Another observation that i made with a tesla coil I built years ago, ill find the photos and post them for you guys, the coil was built in the normal fashion, except i did not do the conventional thing at the doughnut, there i placed a flat circular disc covered in copper foil, then i built two small coils on top of that connected to the flat plate, and a copper ball on top with a short delay line tube to the ball, well guess what the voltage and current phases lined up there was no lag or lead in the power factor.
Something else i realised years later was that at the flat plate the brush was not moving away from the plate but rather moving toward it almost as if the energy was being drawn in.
These are all things that can help I hope not trying to move you guys away from the topic at hand.
Best Regards
Chris

Mr Dove, I know the Delamorto device your talking about I knocked that device up in a couple of lunch breaks at work it lit up a 60 Watt light bulb but it wasn't FE.
It's a bit difficult to visualize your meaning in the plate and brush comments , have you a photo you could please post i'm sure some of us would be interested.

Regards Sil

AlienGrey · « **Reply #23273 on:** February 24, 2022, 03:20:29 PM »

Quote from: magpwr on February 16, 2022, 02:50:32 PM

hi AlienGrey,
Regarding Tesla coil provided if you are comparing between various tesla coil design with respect to frequency.
You may by now noticed that Tesla coil of certain lower frequency produce "blue plama" and "higher frequency" eg:HFSSTC produce hot orange plasma even at a lower voltage source <20volts.
This is the one we should be interested in where even mains bulb can be made to glow easily at low voltage even merely by touching tip of bulb to the Tesla coil.
If you own a high frequency current probe or little cheaper alternative eg:mini RF AMP meter which is connected in series with bulb to Earth.
Then you will know at which Tesla coil frequency would produce a better result.You may already know the AM ferrite rod is good up to 10Mhz but more realistically around 8Mhz or lower. used in Akula kapanadze demo,before the Antenna winding as example.

------------------------------
Lets see what your findings are base on experimental test.

Hi Magpwr 8Mhz would be difficult to produce a self oscillating catcher coil and to get it going as so with 6 or 4 Mhz it wold possibly need 2 inverted driver stages before the NPN 2sc5200 for the feed back oscillation and the 0.6volt device voltage drop would produce a lot of heat as in that mode the bias needs setting to the mid point of the gain locust which draws loads of current before it starts and runs, where an on off rail to rail would work just as well but would be far less energy wast full.

It might be best to use a MOSFET a but that two would need some power full driving due to the charge discharge capacitance
how did you solve that problem ?

#
Regards Sil

NickZ · « **Reply #23274 on:** February 24, 2022, 03:51:36 PM »

Guys:
First time I've seen that there is no Color's thread showing up. Did he finally get the boot?
Or, is that too good to be true? I hope so, as I do miss seeing actual scope shots, and the testing involved. Instead of just religion, and girly pics, talk, talk, and more unrelated talk, etc. Huge yawn factor...

PS. I find that anything over 2 MHz for a Stalker device type Kacher frequency is going to be too weak. If running it at any higher frequency than 2 MHz it just gets weaker and weaker.

NickZ

AlienGrey · « **Reply #23275 on:** February 24, 2022, 05:30:07 PM »

Nick over on Page 96 - 97 re Grumage device and T-1000 info half way down did you and Grum build that device ?
if so did you get any gain ?

Re Color i'm not sure who was actually posting on that thread, could it now be moderated ? Who knows

Sil

NickZ · « **Reply #23276 on:** February 24, 2022, 11:51:25 PM »

AG: As usual, I'm focused on the Stalker self runner versions. Not looking at other stuff. I'll leave that to you.
NickZ

NickZ · « **Reply #23277 on:** February 24, 2022, 11:58:38 PM »

Could not post a correction, sorry.
NickZ

Dove · « **Reply #23278 on:** February 25, 2022, 07:14:23 AM »

AlienGrey Sil
I will do that soonest, All the photos and drawings are on one of my hard-drives saved years ago ill look for them and post.
Chris

magpwr · « **Reply #23279 on:** February 25, 2022, 01:48:00 PM »

Quote from: AlienGrey on February 24, 2022, 03:20:29 PM

Hi Magpwr 8Mhz would be difficult to produce a self oscillating catcher coil and to get it going as so with 6 or 4 Mhz it wold possibly need 2 inverted driver stages before the NPN 2sc5200 for the feed back oscillation and the 0.6volt device voltage drop would produce a lot of heat as in that mode the bias needs setting to the mid point of the gain locust which draws loads of current before it starts and runs, where an on off rail to rail would work just as well but would be far less energy wast full.

It might be best to use a MOSFET a but that two would need some power full driving due to the charge discharge capacitance
how did you solve that problem ?

#
Regards Sil

hi AlienGrey,
I have attached one of my early prototype of HFSSTC using "transistor" at 12volts.
Please try think outside the box and see what you can produce.

https://www.youtube.com/watch?v=-AQmaAEyTic
---------------------------------------

Somebody in forum once mentioned high "frequency is king".There is indeed some truth in it.Which one you think likely produce more supporting Amps blue or yellow/orange plasma.

News:

User Menu

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY (Read 11826809 times)

kolbacict

Re: Kapanadze Cousin - DALLY FREE ENERGY

AlienGrey

Re: Kapanadze Cousin - DALLY FREE ENERGY

Dove

Re: Kapanadze Cousin - DALLY FREE ENERGY

magpwr

Re: Kapanadze Cousin - DALLY FREE ENERGY

AlienGrey

Re: Kapanadze Cousin - DALLY FREE ENERGY

Dove

Re: Kapanadze Cousin - DALLY FREE ENERGY

magpwr

Re: Kapanadze Cousin - DALLY FREE ENERGY

AlienGrey

Re: Kapanadze Cousin - DALLY FREE ENERGY

AlienGrey

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

AlienGrey

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

Dove

Re: Kapanadze Cousin - DALLY FREE ENERGY

magpwr

Re: Kapanadze Cousin - DALLY FREE ENERGY