Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11688536 times)

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #19980 on: June 10, 2018, 11:03:37 AM »
   Itsu:   Ok, well it looks like you have produced the same signals are what Stalker is showing. I believe he compresses the signal (on the scope) to obtain what looks like a sharper peak with not much ringing. I saw how he did that on one of his videos.
I'll look for that, again.
   
   I wonder if some type of snubber added onto the IRF4905 or the other fets, would help to reduce the ringing. Some type of snubber cap and resistor. Apecore had suggestion something earlier, but I don't remember all the details right now. Perhaps check his posts again.
   
   In any case other than the ringing, your set up and signals look how they should look. And more than just good enough for me to follow up on.   
   As you are not using an earth ground, you might consider connecting one up to your water pipes, or where ever you can find something to ground to. I get a better output when the ground line is also connected up to the transistor's emitter. And, perhaps  it might change the ringing signal at bit as well. Connecting up the yoke/grenade may also make some difference in the signals.
   
    We'll see what happens on my end, when I get to that point. As I do use an earth ground line, and have my grenade intact.    Sorry I can't be of more help, as I'm still waiting my parts to get here.
                                                                                                             NickZ
   EDIT.  I wonder if your previous simpler Kacher version which showed a sharper on off signal, might be a better way to go.

Nick,

i think that the setup used in your ringingless kacher video (Adrian?) had a sparkgap at the end of the antenna.
I can imagine that that could cause the ringdown to abruptly stop when the spark fires as momentarily there then exists
a path to ground.

But to test we need a spark capable setup, meaning 1000V or more Kacher voltage and a solid ground.

Itsu

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #19981 on: June 10, 2018, 04:38:28 PM »

See the link, just a short impression of my current setup, showing the kacher interaction related to the voltage at grenade.


https://youtu.be/VP2jjTP22gw

   apecore:  Thanks for showing us your current set up.  I would be interested in seeing what effect the Kacher has on the grenade's output, but at the bulbs. Perhaps you can tell us what you see, as a result of the interaction.  I can see is the scope signals, which seam to look pretty good, but seeing what the effect has at the bulbs, is also needed.
    I notice that you are controlling the kacher pulse to hit the sine wave TWICE, both in the upward as well as in the downward pulse of the sine wave. Normally it's one or the other.  However, Stalker pulses the valley of the sine wave, and not the peaks or the sides. Would you think that that would make any difference? And what are you currently working on now?
   Thanks for sharing.

r2fpl

  • Hero Member
  • *****
  • Posts: 744
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #19982 on: June 14, 2018, 08:50:46 AM »
deleted..

Sorry, this is not the thread, please delete

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #19983 on: June 14, 2018, 04:08:57 PM »
   Itsu:
   Anything new and exciting???
   I have not received anything yet.

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #19984 on: June 14, 2018, 04:45:27 PM »

Nick,   

no, nothing to report as i stopped working on the circuits for now.

I have some idea's to try to get these ringingless bursts, but i don't know if and when i will be exploring them.

Thanks for the info.


Itsu

zalmoxis

  • Newbie
  • *
  • Posts: 39
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #19985 on: June 14, 2018, 11:01:27 PM »
After a year of silence I'm back with new forces and new equipments (Spectrum analyzer and signal generator)
I wanted to let you know that I have managed to get the same results as Stalker did with his small TC4220 , IRF840 drived by the signal generator in pulse mode.
I have teste more than 8-9 grenates what i have built in the past 2 years and just one shows this specific effect. I will attach some pictures.
I want to add some notes, that wire length including ends is 37.5, wire is 2.5mm^2 , an wire diameter is 3,3-3,4mm
The grenate is winded in Ruslan mode/configuration.
The coil radiates maximum on her top head and at the exact frequency of 1,682Mhz
Inductance 324uH
Connecting the cold end to my so called ground (40m of heating pipes) the fluorescent lamp increases in intensity a lot!
I'm very happy to see this result after 2 years of hard work.
Please let me know if someone have got the same effect !


PS: my next step is to build an identical grenate, i will keep you posted

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #19986 on: June 15, 2018, 01:52:36 AM »
Hi congratulations are in order, you must have standing waves. There have been any number of ways published on winding the grenade
I will have a look and see if I can find the original, and see if the effect can be duplicated, I have been a bit busy this last week
with a number of other problems so not much done on the building and testing,  s8uch is life.

Regards AG

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #19987 on: July 03, 2018, 12:33:35 AM »
Can any one shed any light on this ?

AG

Bat1Robin2

  • Jr. Member
  • **
  • Posts: 94
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #19988 on: July 04, 2018, 06:31:45 AM »
That is the grenade coil it has a very specific wrapping the spot you refer to is where i believe the winding changes from cw to ccw or vise versa. The early post will show much more details.

bolt

  • Hero Member
  • *****
  • Posts: 921
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #19989 on: July 07, 2018, 08:38:11 PM »
Seems right too me. The kacher will run at any frequency it likes and it doesn't matter. Lets say 1Mhz  You then chop the katcher to provide sync burst to the collector coil.  The collector coil MUST have a known resonant frequency. In the Khz range lets say 38khz it doesn't matter so long as you know what it is.  The katcher sync is then timed to induce and create the collector 38Khz sine wave by precion burst of the tesla coil 1Mhz pulses.  There is no OU yet this is all sync and tuning. Need to add caps and fine tune the collector coil and yoke collector to max sine amplitude.. still no ou yet just tuning!


THEN turn on power fets to bang sine peaks. Using about 5uS slits and then you might get OU.


Problem katcher is a bad choice its a sloppy sleepy oscillator then keep asking it to sleep for 1500uS then wake up for like 10uS it has a slow start response time as the base current slews all over the place everytime you ask it to wake up so the burst is shitty.  You need a clock driven tesla burst but then you must tune the clock to the antenna and base induction coil aka normal tesla coil tuning.




apecore

  • Guest
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #19990 on: July 08, 2018, 03:48:35 PM »

Problem katcher is a bad choice its a sloppy sleepy oscillator then keep asking it to sleep for 1500uS then wake up for like 10uS it has a slow start response time as the base current slews all over the place everytime you ask it to wake up so the burst is shitty.  You need a clock driven tesla burst but then you must tune the clock to the antenna and base induction coil aka normal tesla coil tuning.


Hi Bolt,

I think this is a main problem....  no OU because the kacher is too sloppy..
And second ....   to get a sharp unipolair puls from the antenna... (package)

Ok to figure out a differnt way is first to understand its meaning.

Do you agree..  the kacher/ HV burst need to collaps the magentic wave inside grenade/ inducor?
Also what matters is its pulsfreq. ... you should think it has to be the same as the grenades resonance freq. so it excites the grenade?

How about (just suggesting) make the inductor "burst" ... it is clock driven...
I would choose to replace the inductor coil....  and put some capacitor/ coil instead (bifilar foil wounded).... letting it spark at APEX...
Only thing to adjust is to get the Inductor wave synchronise the grenade Voltage wave... If we are clocking the burst moemnt at APEX grenade voltage wave?

I don t know if it is possible,...  but when it works it solves the sloppy issue?


Greetings.



P.s. NickZ,...  are you building yuor interupter already?


AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #19991 on: July 08, 2018, 06:48:49 PM »
Seems right too me. The kacher will run at any frequency it likes and it doesn't matter. Lets say 1Mhz  You then chop the katcher to provide sync burst to the collector coil.  The collector coil MUST have a known resonant frequency. In the Khz range lets say 38khz it doesn't matter so long as you know what it is.  The katcher sync is then timed to induce and create the collector 38Khz sine wave by precion burst of the tesla coil 1Mhz pulses.  There is no OU yet this is all sync and tuning. Need to add caps and fine tune the collector coil and yoke collector to max sine amplitude.. still no ou yet just tuning!


THEN turn on power fets to bang sine peaks. Using about 5uS slits and then you might get OU.


Problem katcher is a bad choice its a sloppy sleepy oscillator then keep asking it to sleep for 1500uS then wake up for like 10uS it has a slow start response time as the base current slews all over the place everytime you ask it to wake up so the burst is shitty.  You need a clock driven tesla burst but then you must tune the clock to the antenna and base induction coil aka normal tesla coil tuning.
What!   ;D ;D can you explain that one ?
I will tell you, It will never work the way it is!  there is a reason why it doesn't work if you look at Adrian Gustors Tesla coil you might notice the L2 coil has about 12 to 24 turns on it
have you ever wondered why ? and you couldn't count the number of turns on the Tesla coil so why would that be ? And the L2 is one third from the bottom of the Tesla coil any idea's ?
And as well as that there is no where to store the current or the voltage now why would you want to do that ?

Solve all that then you might crack the problem.

If you were to sling the katcher out you could just wind a tuned coil and place it inside the grenade coil center and supply it with the HV at the resonant frequency and pulse it at a select low frequency.

AG

stivep

  • Hero Member
  • *****
  • Posts: 3567
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #19992 on: July 08, 2018, 08:05:32 PM »

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #19993 on: July 09, 2018, 02:28:19 AM »
   Apecore:   No, some parts have made it to Costa Rica, but now I need to make a long 4 hour trip to pick them up.I will be getting them this week, I hope, if all goes well.

   It has been a bit disappointing that no one is continuing to build and test this Akula/Ruslan type of device. Even Itsu has a hard time getting the pulse packets to work right. I don't know if I can do any better. 
   Anything new with you. Staying out of the bars??? Or drinking alone...

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #19994 on: July 09, 2018, 11:43:21 AM »
.
« Last Edit: July 09, 2018, 06:34:11 PM by AlienGrey »