Hi Lost bro

Yes, Finaly......someone is starting to see it
that is part of the key, The negative period (1/2 period wave) is cut off by the HV Ultra fast diodes
You only need the Positive halve from Tesla. You only want to call in Ions ( radiant energy )
and not to remove it but to store it and use it in the flow of the spin.
Ground will provide the negative charges. The Tesla will take away what it has givin if full period is done.
Other part  of this is all the correct tuning of the coils Wavelenght and  Freq match.


Cheerz~

Hi Geo,

Sounds like you have been PM'd by Enjoykin. 

Hi Lost bro

Yes, Finaly......someone is starting to see it
that is part of the key, The negative period (1/2 period wave) is cut off by the HV Ultra fast diodes
You only need the Positive halve from Tesla. You only want to call in Ions ( radiant energy )
and not to remove it but to store it and use it in the flow of the spin.
Ground will provide the negative charges. The Tesla will take away what it has givin if full period is done.
Other part  of this is all the correct tuning of the coils Wavelenght and  Freq match.


I have currently a second setup now with exact measurements of wirelenghts for the travelling waves
Which is now under experimentation and there is super positive results now and complete different behavior
and could really say, it looks like how ruslan has shown it on some of his videos back than.

I will soon enough show some demo's when i'm done.
Exciting times ahead now .

I think there is enough info now and everyone if comprehended well, now do this right,.

Cheerz~

Good day GeoFusion

Quick question: How did you calculate the capacitor value for the Inductor / Yoke circuit?

Did you have an 'Inductance meter' (L/C/R)?

What I am getting at is that this is a critical part of the Frequency puzzle.  It is the feedback frequency from this part of the circuit that drives and *regulates* the 'Push-Pull' which in turn is the heartbeat of the Grenade.

The 3 windings on the Yoke coil have an Inductance, and the 10 or so meters of windings on the Inductor have another distinct Inductance.  Both of these inductances are cumulative for the calculation of the 'C' for the series resonant *Inductor* circuit and as such any difference in the cross section and/or permeability of the Yoke core material will vary this cumulative inductance from that of Ruslan's device. Meaning that just using a .47uF cap. because Ruslan did, will NOT work........ unless you have the same exact yoke core as Ruslan (even if physical dimensions are the same, permeabilities can vary for the SAME piece from different manufacturing dates, let alone different companies)

This will necessitate a change of value for the calculated 'C' or a modification of the winding count (yoke/grenade) of same circuit in order to obtain the wanted/needed/calculated Fres.

Have you measured the Fres of your series Inductor/yoke circuit?

Just something to think about.

take care, peace
lost_bro

Hi Hoppy Good day to you.


There in the text there are the last keys exposed to what needs to be focused on.
if these texts wont help anyone, than they don't need to bother continuing .
enjoy .

Cheerz~

Hi Geo,

Yes, this detailed info should be of much help to those with the understanding and skills to implement.

The negative period (1/2 period wave) is cut off by the HV Ultra fast diodes You only need the Positive half from Tesla.

I'd like to remind everyone, that diodes don't rectify voltage.  Diodes rectify current.

I'd like to remind everyone that diodes don't rectify voltage.  Diodes rectify current.

Good point Verpies,

Thats also wy i wonder how Geo has these diodes connected.
On the internet there are different types of setups with kacher transistor diodes.

1- Wouldn't it be a idea to place a diode in series withe the ferrite coil...  so only positive/ negative current goes to antenna?
2- Or is it nescessary to drain it all to ground from top of the secunfairy (kacher)...

Greetings

You guys all remember this one don't you:
http://www.youtube.com/watch?v=GmlpV1MWm40

What do you suppose those coils are doing beyond being simple inductors...?

I say, they are configured in such a way to create a parametric oscillation; if they weren't, Nelson would have connected a battery in order to make those LEDs glow.

Short of hitting us over the head with the answer, Nelson gave us plenty to ponder in that little video.  How about we start asking ourselves the right questions...

You guys all remember this one don't you:
http://www.youtube.com/watch?v=GmlpV1MWm40

What do you suppose those coils are doing beyond being simple inductors...?

I say, they are configured in such a way to create a parametric oscillation; if they weren't, Nelson would have connected a battery in order to make those LEDs glow.

Short of hitting us over the head with the answer, Nelson gave us plenty to ponder in that little video.  How about we start asking ourselves the right questions...

Good day Dog_one,

I think your right.
As i maybe wrong but wasn't there a schematic of that nelson's led_selfrunner posted on this forum a while ago?
If so, i would suggest to do some back engineering on that schematic as it would give maybe the right answers.
Otherwise it would lead to the right questions. etc. etc.

Hoppy,... are you suggesting that that object might be a variant of a parametric coils_combination as shown in the posted video by Dog_one?

Greetings

  I believe that Nelson wraps the normal transformer with copper or other materials and takes the high voltage off of the metal wrap.