as you please!

@JUSTAWATT

As you requested better late than never

Hope it helps

jj

it's a bit old now as does not have driver equalisation in this circuit.

Also this guy is obviously at it too. https://www.youtube.com/watch?v=CbH9WPOrZfQ


https://www.youtube.com/watch?v=LyHJN_ztOsw

kapanadze's weird noise motor-generator 2016
https://www.youtube.com/watch?v=qUlLDQkqreA

I tried to use a tesla like coil (200 turns) underneath the Grenade coil instead of the inductor.
Series resonance was set using some wima caps around 15KHz using the push-pull setup.

The result was minimal, about 20V dc coming out of the grenade, not able to light up a bulb.

Then i set up the tesla like coil in parallel resonance with similar wima caps as a stand-alone circuit (around 15KHz)
and added again the inductor coil (3 layers bifilar half the length of the grenade coil) and series resonate that also around 15KHz
with the push-pull.

The result was slightly better, but a 100W bulb was barely lit.

The nano-pulse in both above cases causes the voltage/light to further decrease/dim somewhat.

So the power transfer into the grenade coil in both cases is very bad (due to the coax inbetween the grenade and the inductor?)
and adding the nano-pulse only worsen that.

Finally i tried to measure the VSWR (Voltage Standing Wave Ratio) of the grenade, as that suppose to have (i think) a frequency where
it shows a worse VSWR so we could setup a standing wave on that frequency.

However, there is no such frequency to be found in a 1.5GHz range, only some good = low VSWR points are found.
So i am puzzeled about these references to tune the grenade to a worse VSWR so we can setup a standing wave doing its magic.


Video here:  https://www.youtube.com/watch?v=6htOsexWFGk


Regards Itsu

Hi Itsu
We have discussed it again before a year but seems that you forgot it. See attached image.

We measure an accurate length for our inductor for one reason. For being able to vibrate at the same high frequency as with our grenade. By forcing it down to KHz with the series cap is absolutely without any meaning. Ruslan seems that purposely made a mistake on here...

I tried to do the same but i can not tune it. I'll try again next week as i will have some time to play with. For now i took a break messing around with JohnK1's circuit. Looks interesting as in simulation creates sharp one way pulses at the output! I hope that Jan made some progress on this.

You need to tune it ti the Freq you want it tuned to, not any old F or it won't work and that caption has a coil that's wound in a different way so the values shown aren't correct, know what your doing or the coil might just get red hot and start a fire, oh yes !

Hi Itsu
We have discussed it again before a year but seems that you forgot it. See attached image.

We measure an accurate length for our inductor for one reason. For being able to vibrate at the same high frequency as with our grenade. By forcing it down to KHz with the series cap is absolutely without any meaning. Ruslan seems that purposely made a mistake on here...

I tried to do the same but i can not tune it. I'll try again next week as i will have some time to play with. For now i took a brake messing around with JohnK1's circuit. Looks interesting as in simulation creates sharp one way pulses at the output! I hope that Jan made some progress on this. 
 

Hi Jeg,

i was looking at the thread about a year ago, but do not see the discussion you mention, or do you mean by: "We have discussed it again before"
a discussion among other members?

I only found this post from T-1000: 

http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg454232/#msg454232

Here he translate something and he states:

"The only difference is you are dealing with non-Hertzian waves and the SWR has to be maximum inside of grenade coil as opposed to conventional tuning."

Itsu

Hi Jeg,

i was looking at the thread about a year ago, but do not see the discussion you mention

Hi Itsu
Sorry for not being more clear. I was referring to your series connection between your inductor and cap. Not about your VSWR measurements. We were saying about the affection of your probe when you connect it in parallel with your inductor and the high frequencies that get rise due to probe's capacitance. I will try to locate the post even it is very hard to do that among all those pages!

D1 thanks for this video.

NickZ, do you have any other details? Like which coils are in the same core? The circuit is not very clear to me.

Not certain, but maybe this video is worth a refresher:

https://www.youtube.com/watch?v=kH3ETTd6bPI

"No antenna.  Very intense ground."

interesting and in a sense relative but the wrong video you need the other video i think it's called lonesome pine crystal set challenge, something like that but it's no longer on youtube the took it off. but i think he will sell you a copy, if i'm not mistaken it's this you want / need http://www.crystalradioinitiative.com/