Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11719475 times)

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #14250 on: May 26, 2016, 01:21:27 AM »
 Curious thing, but I'm onto the same situation concerning rectifying the 28 turns coil to DC, to be fed to the Kacher's input.
If the voltage off of the 28 turns coil is over 1000v, I'm supposed to rectify that and feed it into the Kacher??? I hope that the 2SC5200 transistor can take it? At least my horizontal deflection transistor was a 1500v.  So, we'll see what gives, first.
  What are the best diodes to use?  I'm trying out some IN5408 for the bridge after the 28t coil. Which is NOT connected to the grenade's 168t coil in this case.   
 
   I've also added Geo's mediator coil into the device, and now it seams to help keep the heat down a bit on the Kacher's transistor.
So that I'm able to run the Kacher without a fan, just a big passive heat sink (heater). As I hate fans...

  Here's a pic of my 1 1/4 inch green toroid which is now being used for the mediator coil. 
  I had made a mediator coil out of a yoke previously, (pictured below) which was when I had my burn out problems.
Hopefully this smaller mediator will work out ok, but I'm still going to add a couple more of the chokes that I had on there before, just in case. 
  Here's a pic of my device with the "Yoke Mediator"  which was what killed my Mazilli.  I'm going to get that Mazilli up and running soon, also. As it was a beast...


  So, Geo.  How's it going???

Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #14251 on: May 26, 2016, 07:16:48 AM »
Because it works as a load.  Measuring across a load gives you a current reading (not a voltage reading).
You can accomplish a very similar rectification with a single diode connected across points A and B in your diagram, while the other diode is deleted and replaced by a piece of wire.

Your confusion arises because you forgot that real diodes do not rectify voltage - they rectify current.
Once you set up your jig to measure the current flowing through the diode, everything will clear up.

This makes clear a lot of things. Indeed, i thought that a diode rectifies voltage! All of my confusion started from this wrong assumption  ::) Thanks for the clarification Verpies. I appreciate it.  ;)

Tomtech29

  • Sr. Member
  • ****
  • Posts: 447
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #14252 on: May 26, 2016, 08:27:30 AM »
Curious thing, but I'm onto the same situation concerning rectifying the 28 turns coil to DC, to be fed to the Kacher's input.
If the voltage the off of 28 turns coil is over 1000v, I'm supposed to rectify that and feed it into the Kacher??? I hope that the 2SC5200 transistor can take it? At least my horizontal deflection transistor was a 1500v.  So, we'll see what gives, first.
  What are the best diodes to use?  I'm trying out some IN5408 for the bridge after the 28t coil. Which is NOT connected to the grenade's 168t coil in this case.   
 
   I've also added Geo's mediator coil into the device, and now it seams to help keep the heat down a bit on the Kacher's transistor.
So that I'm able to run the Kacher without a fan, just a big passive heat sink (heater). As I hate fans...

  Here's a pic of my 1 1/4 inch green toroid which is now being used for the mediator coil. 
  I had made a mediator coil out of a yoke previously, (pictured below) which was when I had my burn out problems.
Hopefully this smaller mediator will work out ok, but I'm still going to add a couple more of the chokes that I had on there before, just in case. 
  Here's a pic of my device with the "Yoke Mediator"  which was what killed my Mazilli.  I'm going to get that Mazilli up and running soon, also. As it was a beast...


  So, Geo.  How's it going???
hello
you still need a little experiment and make certain verifications
and where there come from 1000?
"off of 28 turns coil is over 1000v"What...
This system could act as find a way to shift the phase current!
See the movie:
https://www.youtube.com/watch?v=4H6Q7Uthow4
when this happens?
- you have to dig deeper.

Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #14253 on: May 26, 2016, 12:19:32 PM »

  What are the best diodes to use?  I'm trying out some IN5408 for the bridge after the 28t coil.

I use the same diodes Nick, for the same task. They work just fine without any problem.

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #14254 on: May 26, 2016, 03:10:48 PM »
  Jeg:
  The reason I asked about the diodes is because when I previously tried to rectify the output of the grenade's 168t coil, using those same diodes, they got so hot that they would melt the solder points.  But, for now I'm just using the Kacher's output as an input source for the Kacher, only, as I don't have the induction circuit working, yet.  But, as there is HV going through the 3t coil circuit, and the 28t coil also from the Kacher's output, I'm trying to see if I can get the Kacher to self feed-back itself, with the same output from the Kacher, going back to the Kacher. As I have a feeling that the induction circuit may not really be needed, at all.  Or not???
 
   Today I'll complete the full bridge rectifier using those IN5408 diodes, for the Kacher's input source from the 28t coil. This 28t yoke secondary coil will NOT be connected to the grenade.  As I could not find resonance between the Kacher, and the induction circuit previously, with the 28t yoke coil connected to the grenade's 168t coil. And now my Kacher is stronger than it was before.
And, it looks like he stronger the Kacher's output, the brighter the bulbs, and "effect".
 
   Thanks for the reply.  And good luck with your project.

   TomTech:  With the induction circuit running, and NO load, I get was getting over 1000v output from the 28t coil. With or without the grenade connected. This was the normal output of my set up, when using the Mazilli as the driver, when it's running on a 12v, or 24v source.

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #14255 on: May 26, 2016, 05:38:26 PM »
  Jeg:
 
   Today I'll complete the full bridge rectifier using those IN5408 diodes, for the Kacher's input source from the 28t coil. This 28t yoke secondary coil will NOT be connected to the grenade.  As I could not find resonance between the Kacher, and the induction circuit previously, with the 28t yoke coil connected to the grenade's 168t coil. And now my Kacher is stronger than it was before.
And, it looks like he stronger the Kacher's output, the brighter the bulbs, and "effect".
 
   Thanks for the reply.  And good luck with your project.

   TomTech:  With the induction circuit running, and NO load, I get was getting over 1000v output from the 28t coil. With or without the grenade connected. This was the normal output of my set up, when using the Mazilli as the driver, when it's running on a 12v, or 24v source.
Nick don't use 1N5408 diodes they are far too slow for this type of work get some FAST low break over voltage type. Like MUR460's

Use something like this http://www.onsemi.com/pub_link/Collateral/MUR420-D.PDF
« Last Edit: May 26, 2016, 11:19:56 PM by AlienGrey »

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #14256 on: May 27, 2016, 12:07:46 AM »
  AlienGrey:
  Yes, thanks,  I'll see what I can do, but for now the IN5408 diodes have already been installed. We'll see how they work out for this. I can always switch them out, if they don't do the job.
  I'll be getting stronger 4A diodes like the MUR420 (25ns) that you recommended, to build the full diode bridge, that will be mounted on a heat sink for the grenade's 168t output coil. They're also really inexpensive. But, they can't be mounted on a heat-sink, for added cooling, like the 220 package ones can.
 
  I'd like ask Itsu how his bridge diodes were working out, as far as heating up, or not. And which diodes he is using.

GeoFusion

  • Sr. Member
  • ****
  • Posts: 449
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #14257 on: May 27, 2016, 12:57:53 AM »
Hi guyz :)

 Nick,
Well there is alot of good news and alot still to test :).
hopefully to post a new vid for the eyes to see what is going on.
But I wanted to point out to not really use the smaller green toroid, just use the Yoke as mediator for the work.
The diameter of what the yoke ferrite is perfect.
The red windings ( secondary ) on mediator yoke should not be to thick. use thin wire about 1mm diameter.
reason why you also fried some of your circuitry. The voltage you see on 28T is not correct, it's the ions
that are making the false readings on meter, 28T will generate a amount when having power supply connected to
mazilli as how it should but the mix will happen eventually as you see ;)
But you could just use the White windings for the mediator to work, one end on the positive rail and output end
both katcher & mazilli positive connecting to it and negative rail direct to power supply.
So as I have read you want to hook it up as original way, the Roman way :)
alot of tuning required. But the Ruslan way will be easier for you Nick :),
is what I am doing now. Roman's way will come in play soon enough. T-1000 will show it working too :).
A TL494 and driver is needed to able to tune it where it is. but If the mazilli's fixed freq is there already, that would be nice.
but what will be interesting to see is when you synchronize them with the mediator ;) with current setup.
See if it works out with a mazilli/royer circuit. But remember you need atleast a Tl494 & diver board.


Cheerz~

lacphong

  • Newbie
  • *
  • Posts: 21
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #14258 on: May 27, 2016, 06:48:37 AM »

GeoFusion,
It's good to hear that you're getting some positive results finally.  Can you tell us which schematic you are using for your set up that is working right now?


Thanks in advance.





Hi guyz :)

 Nick,
Well there is alot of good news and alot still to test :) .
hopefully to post a new vid for the eyes to see what is going on.
But I wanted to point out to not really use the smaller green toroid, just use the Yoke as mediator for the work.
The diameter of what the yoke ferrite is perfect.
The red windings ( secondary ) on mediator yoke should not be to thick. use thin wire about 1mm diameter.
reason why you also fried some of your circuitry. The voltage you see on 28T is not correct, it's the ions
that are making the false readings on meter, 28T will generate a amount when having power supply connected to
mazilli as how it should but the mix will happen eventually as you see ;)
But you could just use the White windings for the mediator to work, one end on the positive rail and output end
both katcher & mazilli positive connecting to it and negative rail direct to power supply.
So as I have read you want to hook it up as original way, the Roman way :)
alot of tuning required. But the Ruslan way will be easier for you Nick :) ,
is what I am doing now. Roman's way will come in play soon enough. T-1000 will show it working too :) .
A TL494 and driver is needed to able to tune it where it is. but If the mazilli's fixed freq is there already, that would be nice.
but what will be interesting to see is when you synchronize them with the mediator ;) with current setup.
See if it works out with a mazilli/royer circuit. But remember you need atleast a Tl494 & diver board.


Cheerz~

Dog-One

  • Hero Member
  • *****
  • Posts: 1019
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #14259 on: May 27, 2016, 08:17:51 AM »
It's good to hear that you're getting some positive results finally.


It won't be too much longer, Geo will be saying:


"I'd be happy to burn your light bulbs out."
  -- Donald L. Smith - 1996 Tesla Symposium

lost_bro

  • Sr. Member
  • ****
  • Posts: 282
    • youtube channel
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #14260 on: May 27, 2016, 05:34:38 PM »

It won't be too much longer, Geo will be saying:


"I'd be happy to burn your light bulbs out."
  -- Donald L. Smith - 1996 Tesla Symposium

Good Day all:

Could resist this one so:

https://www.youtube.com/watch?v=K9xCEgDaUlA

This is how to burn out/explode any light bulb you might be wanting to get rid of:

Take care, peace
lost_bro

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #14261 on: May 27, 2016, 07:42:04 PM »
  AlienGrey:
  Yes, thanks,  I'll see what I can do, but for now the IN5408 diodes have already been installed. We'll see how they work out for this. I can always switch them out, if they don't do the job.
  I'll be getting stronger 4A diodes like the MUR420 (25ns) that you recommended, to build the full diode bridge, that will be mounted on a heat sink for the grenade's 168t output coil. They're also really inexpensive. But, they can't be mounted on a heat-sink, for added cooling, like the 220 package ones can.
 
  I'd like ask Itsu how his bridge diodes were working out, as far as heating up, or not. And which diodes he is using.

Hi Nick,

i am using 12r06di  diodes and they are not getting warm, but are mounted on a fairly big heatsink.

Itsu

a.king21

  • Hero Member
  • *****
  • Posts: 1650
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #14262 on: May 28, 2016, 10:08:43 AM »
Understanding Kapanadze. Benitez stated that if you charge one plate of a capacitor and ground the other plate through a transformer the ground will give you the same through eletrostatic induction. It's ac (kind of) as you can see on the neon bulb in my replication.


https://www.youtube.com/watch?v=Jnee3xSxP4U


This echoes what Don Smith was saying.

Utopia Now

  • Full Member
  • ***
  • Posts: 100
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #14263 on: May 29, 2016, 12:56:36 AM »
Here also  a video about the extra charging effect (on a capacitor)  when "Earth Grounding" is connected.
Video on Youtube : Resonance effects for everyone to share test 1       https://www.youtube.com/watch?v=4mr3Xikrgak

Utopia Now

  • Full Member
  • ***
  • Posts: 100
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #14264 on: May 29, 2016, 01:00:29 AM »
This is a picture from the video : resonance effects for everyone to share test 1