Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11717662 times)

starcruiser

  • Hero Member
  • *****
  • Posts: 693
    • Starcruiser's Place
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12705 on: March 13, 2016, 09:32:32 PM »
@void,

Yes it is, I worked on TV repair some years back and understand the horizontal and vertical sweep frequencies of the old CRT based sets. typically most run at 15.725Khz (or close) for the horizontal refresh rate and the vertical is usually at line rate, this is 60Hz in the US and similar markets where the AC line rate is 60Hz, in the other markets this is 50Hz, thus the 2 standards of NTSC and PAL for the video.

For color TV's the time base was around 3.58Mhz for the color signals which are on the back-porch of the Horizontal sync pulse for sync'ing.

ANyways, the yoke core is designed to operate in that frequency range and will have issues with signals above this frequency. Thus the old yoke cores are less reactive to the higher frequency of the Nano pulse or the Telsa coil. Using a newer torrid core is not a good idea when working in the lower Khz range as it is not going to respond as well or will allow the higher frequency pulses to overload the lower frequency driver stage as it will back bleed and most likely kill the MosFets due to the high voltage this allowed to pass.

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12706 on: March 13, 2016, 10:18:54 PM »
Hi Star,

you are so right, i happen to be using my T520-2 toroid in a loss-less clamp setup, but it is not so stable as i hoped for, probably because what you were saying.

The T520-2 is designed for 2-30Mhz, so i had to use more primary windings (52 double magnet wire (1mm) turns for each primary) to get the push-pull to even start working.
They measure 88uH each and cover each a half of the toroid closely wound at the inner circumference, see picture.


The signals across the drains/source of each MOSFETs shows  oscillations as can be seen in screenhot 1
The Spectrum Analyzer shows that more frequency peaks are involved, see screenshot 2
One thing that did improve was that the 4 stacked magnets have no influence anymore on this setup, and no audible hissing was heared when tuning  :)


Itsu

verpies

  • Hero Member
  • *****
  • Posts: 3473
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12707 on: March 14, 2016, 02:58:07 AM »
The signals across the drains/source of each MOSFETs shows  oscillations as can be seen in screenhot 1
The oscillations are so asymmetrical between the two MOSFETs !!!
What causes so much asymmetry horizontally & vertically ?


verpies

  • Hero Member
  • *****
  • Posts: 3473
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12709 on: March 14, 2016, 03:24:45 AM »
My question referred to the asymmetry of signals between two identical MOSFETs - not the asymmetry of the architecture between drains and sources of MOSFETs.

stivep

  • Hero Member
  • *****
  • Posts: 3567
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12710 on: March 14, 2016, 03:36:45 AM »
My question referred to the asymmetry of signals between two identical MOSFETs - not the asymmetry of the architecture between drains and sources of MOSFETs.
when you do not have symmetry ( paired  properties) that it is hard to ask for symmetry in signals .
The  additional consideration is  impedance symmetry.
Presence of  reactances  changes with not only frequency but with shape of the input signal  processed independently.


e.g. square wave is  made out of http://www.mathworks.com/help/matlab/examples/square-wave-from-sine-waves.html?requestedDomain=www.mathworks.com
there you have it, when  you  average component  harmonics
in square wave the top is DC and what  is significant is leading edge and falling  edge. (AC) There are important harmonic components forming the edges. So in the bridge mode when you have distribution of the signals individual impedances of interacting sine waves with its newly created reactances  matters.(  identical distribution is  expected)


Wesley
« Last Edit: March 14, 2016, 06:25:46 AM by stivep »

hartiberlin

  • Administrator
  • Hero Member
  • *****
  • Posts: 8154
    • free energy research OverUnity.com
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12711 on: March 14, 2016, 04:20:36 AM »
hi everyone
check out this circuit and see the video link
maybe this could be the last thing we can try to get free energy.
the video does not belong to me.
But i have made circuit based on the video ,i would like some one to try this circuit.

https://www.youtube.com/watch?v=5K3HrhH5Qrs

https://www.youtube.com/watch?v=RUF7eJAOjF4


I think the circuit diagram on this is wrong, as it does not need a ground
and it seems it just uses only 2 Teslacoils in some kind of oscillator circuit and
the battery is only delivering probably not much more than 100 Watts, as judging from
when  connecting the cables and the arc that is involved at this moment...
So below the white towel are probably some transistors to get these 2 Teslacoils oscillating
with the higher turn coils and the 2 x 6 Windings copper coils will just be the
output coils probably put in series via the standing blue electrolytic cap...

So it seems to be a power amplificator circuit, maybe on the phase shift of the 2 x 6 winding copper
coils always being maybe 90 degrees out of phase, so they do not drag each other down, so this oscillator
maybe a Lenz law violator...
As I find this device very easy to build and also does not seem to need a ground cable, this could also be used for
mobile applications like cars or electric bikes, etc...
So it is a very interesting device and probably easily to replicate...

Regards, Stefan.

stivep

  • Hero Member
  • *****
  • Posts: 3567
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12712 on: March 14, 2016, 05:04:52 AM »



That was  some time ago when I introduced  electrostatic pump theory.
It was working based on phenomena of electron inertia.\
The mass of electron is small but that mass while is moving  in conductor creates significant  heat.
In series of impulses electron does not stop in the intervals  between the pulses.
for that I foresee ground to be essential.
However ground plane antenna antenna works with its artificial  ground at 10floor of the building and that is sufficient size metal plate that this antenna is standing at.  for car  FM antenna the counterpoise is the metal body of the car. In some of the applications there is small tuning resonance circuit  between  metal body and antenna.






The theory relates to electrons flow due to  difference of potential from the ground to the device.
There is coil ( receiving coil)on the side that is  coupled in near field to the coil that is connected  between ground and the end destination  of the electron flow.
the ratio between that coil and receiving coil is up to us to decide.
At the  receiving coil  there is capacitor in parallel that is creating tunned circuit to resonate with the first coil.
 part of the energy flow from the ground.
the missing part of that theory is the mechanism of recovery of energy used by the load vs energy  sustaining that pull(  HV potential) 
In theory that would be no problem to use ionosphere /earth  potential difference and put our load on its way.


I have made analogy that car that pushed by 15  15years old girls after the wile requires 1 girl to push the car and then only 1 finger of  that girl to sustain the motion and compensate the losses.
I have  made analogy   to person trying to suck  gasoline from the car to the container  using flexible tubing.
The first he is introducing initiating force with his mouth  and that gravity does the rest.
So missing part of that theory is actually  me pointing at additional force that sustain device to pull electrons from the ground


This is part of it:
https://youtu.be/GnE1fjVANS8?t=516





and here is the rest
https://youtu.be/GnE1fjVANS8?t=650
but mechanism of that phenomena must contain the same set of elements ( in different form) as the example with the fuel "pumped" from the car.

Wesley

T-1000

  • Hero Member
  • *****
  • Posts: 1738
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12713 on: March 14, 2016, 10:25:04 AM »
Hello,

For the phenomena Wesley (stivep) is describing "the right moment" for high voltage spike to go through over capacitive  link to the ground seems is on the peak of current in the coil - https://youtu.be/Wt68ehFYVs4?t=16s
Bearing in mind about the support of high tension electrical field spike which do not require much amount of energy to sustain from the mutual power amplification effect being created - that may be root fundamental in Kapanadze style device.
We shall see if we can reproduce that in ongoing replication...

Cheers!

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12714 on: March 14, 2016, 10:27:39 AM »
The oscillations are so asymmetrical between the two MOSFETs !!!
What causes so much asymmetry horizontally & vertically ?

Yeah, i noticed that to, and tripple checking on the new toroid windings (first without the 4 turn secondary, later with it) did not show any wrong wiring.
I traced it back to the gates, the yellow MOSFET gate has these oscillations, the blue not, but is shows on both outputs.

Need to further stiffen up the driver voltage (12V) i guess.
It could probably be the cause of the oscillations with the yoke loss-less clamp setup to

Itsu

ramset

  • Hero Member
  • *****
  • Posts: 8073
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12715 on: March 14, 2016, 01:26:08 PM »
Wesley
Have you ever heard of this man or about this crazy simple experiment in 2001 ?
http://www.energeticforum.com/renewable-energy/20419-hawkings-generator.html

Chet


Dog-One

  • Hero Member
  • *****
  • Posts: 1019
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12716 on: March 14, 2016, 02:42:11 PM »
For the phenomena Wesley (stivep) is describing "the right moment" for high voltage spike to go through over capacitive  link to the ground seems is on the peak of current in the coil - https://youtu.be/Wt68ehFYVs4?t=16s
Bearing in mind about the support of high tension electrical field spike which do not require much amount of energy to sustain from the mutual power amplification effect being created - that may be root fundamental in Kapanadze style device.

In that particular video Ruslan demonstrates a CRT yoke is not needed.  He is clearly using an E-core to build current in the induction heater coil.  This should eliminate any factor of the yoke being necessary for OU operation.

This phenomena appears to me to be a case of reactive power amplification.  You have an idle condition where voltage and current is 90 degrees out of phase and you introduce an external high voltage source that is in-phase with the current.  This creates a condition where you now have real power that can be extracted.  Somehow the external voltage source is mixing with the available current in the tank circuit.  I think two things must be happening here.  We are getting electrostatic induction into the grenade coil from the external high voltage source AND we are getting magnetic induction into the external high voltage coil from the induction heater coil.  Both are happening simultaneously.

How can this work?

Two circuits:
   1st inductive -- voltage leading current
   2nd capacitive -- current leading voltage

When brought together and mixed in the grenade coil, the phase mis-alignment of each circuit is compensated by the other, creating two conditions of real power, one which we draw out to power the load and the other compensated by equalizing to earth ground.  Each circuit only "feels" its reactive component as would happen in any properly tuned tank circuit.  When mixed though, there is real power to be extracted since two conditions exist where voltage and current are in-phase.

I've thought many hours about this and see no other way this could work.  It's just a matter of getting each circuit tuned with the common mixing point (grenade or Dally coil).  We should be able to attack each circuit with its partner shut down and observe the proper wave forms and phase alignment.  Then we turn on both circuits; magic happens.



Void

  • Hero Member
  • *****
  • Posts: 2333
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12717 on: March 14, 2016, 03:11:37 PM »
hi everyone
check out this circuit and see the video link
maybe this could be the last thing we can try to get free energy.
the video does not belong to me.
But i have made circuit based on the video ,i would like some one to try this circuit.

Hi justawatt. Welcome to the forum. You didn't mention where you got that schematic drawing from.
The person who made the videos you linked to covered up the circuitry and also taped over the
top of the blue vertical tube. They obviously don't want people to know the details of what they are doing.
I guess someone was just guessing based on what they see in the videos when they made that schematic?

Regarding the schematic you posted,  whatever is in that blue vertical tube is not likely at all an electrolytic capacitor.
There also does not appear to be any earth ground wire connected to the circuit in the video, but some of the schematic
otherwise looks like it might possibly be potentially close to the rest of the circuit layout which we can see in the video.
Can you provide some specific details about what is the origin of that schematic and what it is based on?

You said you built the circuit. What are your results with your testing?

All the best...

Void

  • Hero Member
  • *****
  • Posts: 2333
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12718 on: March 14, 2016, 03:36:08 PM »
Hi Dog-one. Yes, it would seem that this is a possibility for how this sort of circuit might work,
and something I have been conducting various experiments with as well. I still
don't see anything too earth shattering, so far at least. :)

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12719 on: March 14, 2016, 04:39:01 PM »
   Justawatt:
   I don't see the part where the battery is disconnected from the circuit. So, not a self runner, like is being mentioned in the tittle of the video. It's just an inverter.  Or what?
   These videos are showing something we'll never know how it was done, or what was done. No schematic of the driver circuit, either. So, How could you replicate it, not knowing the basic layout and circuitry? 
   And I'll bet that your result were....  Not self running...