Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11719950 times)

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12165 on: February 15, 2016, 06:39:16 PM »
Hoppy,

I will do measurements when I have it up and running again, need to fix the Pushpull still.
But take a look at the provided link of Ibrahim ( URFA) He shows some readings there when Kacher connects
and when effects plays.

Cheerz~

Geo,

Good luck with the repair.

URFA needs to show the input current next to the voltmeter. He should also scope the PWM drain to source waveform on both mosfets to show how the duty cycle is being affected by connection of the Kacher.

T-1000

  • Hero Member
  • *****
  • Posts: 1738
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12166 on: February 15, 2016, 07:25:04 PM »
T-1000,

thanks for your info, i doubt the ucc37322 is to slow, it is specified at 20ns rise/fall times which seems faster then the IR2184.
It will take major rebuilding to change it over, but i will keep it in mind if anything else fails (i don't think it will be of much influence as the resulting resonance sine waves are clean, but i just want to understand what is happening in my setup).

Not sure i understand what you are saying about the pin / chip layout (pin 14 of the IR2184?)

Itsu
The easy way to see if there is mosfet gate timing problem is to temporary swap transformer to pair of resistors then see on scope if the mosfets output signals overlap.
For the mosfet driver chip it is 8 pin variant used in Oleg circuit for the single mosfet and my suggestion was to use 14 pin variant which drive both mosfets - http://www.irf.com/product-info/datasheets/data/ir2184.pdf
Also the dead time before mosfet switch-on is required for BEMF spike to finish from previous half-cycle.

Cheers!

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12167 on: February 15, 2016, 08:29:16 PM »
   Geo, Hoppy, and All:
   URFA is on line here as I type this note. So maybe direct your suggestions to him.
   What I'd like to know is if he has his device self running, yet?  Or what's the point of taking suggested readings.
 
   I have not watched his video yet, but I will.

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12168 on: February 15, 2016, 09:09:11 PM »
   Geo, Hoppy, and All:
   URFA is on line here as I type this note. So maybe direct your suggestions to him.
   What I'd like to know is if he has his device self running, yet?  Or what's the point of taking suggested readings.
 
   I have not watched his video yet, but I will.

No point - he will no doubt have read them.  ;)

Void

  • Hero Member
  • *****
  • Posts: 2333
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12169 on: February 15, 2016, 09:14:47 PM »
   Geo, Hoppy, and All:
   URFA is on line here as I type this note. So maybe direct your suggestions to him.
   What I'd like to know is if he has his device self running, yet?  Or what's the point of taking suggested readings.
    I have not watched his video yet, but I will.

For GeoFusion and NickZ:
URFA made it clear back in Oct 2014 that the current draw to his PWM driver increased substantially
when he switched on the kacher and the lights got brigher.  URFA stated himself that it was not an OU
effect. Here's what URFA said about it back then:

"In my setup.
Power consumption of kacher: 24 V  1.8-2 A
Power consumption of push pull driver circuits: Without kacher 24V 2A but I measured when kacher runing Its power consumption is growing about 24V 7-8 A.
Power consumption of kacher and push pull driver totally 9-10A(24V)
I have 4x40w and 1x100w  220v light bulbs. Totaly 260w and When kacher run they are fully brightness.
My setup not OU.I only share this video with you to show the effect of Kacher. I'm still working on this system like you."
( http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg421773/#msg421773 )

As we all know, it is very difficult to judge the true brightness of bulbs with any degree of real accuracy just by
looking at them. Are they 75% bright, 80% bright, 90% bright? In reality this is really hard to tell accurately.
In the least you have to be carefully measuring the the input power consumption of both the kacher and PWM driver
when testing, otherwise it is like trying to cross an ocean in a row boat without oars and without even a compass.
You are going blind and are completely at the mercy of the wind and currents. You may guess at where you are and
where you are going, but you could be way off the mark. :)

URFA also mentioned that he saw no significant effect from connecting earth ground when he was running from batteries,
but he saw some effect when connected to a mains connected power supply.

Using a mains connected power supply is convenient when just doing basic circuit testing, but for any serious testing
looking for an OU effect with this setup you have to power from batteries only. That should be a given at this point. ;)
« Last Edit: February 15, 2016, 11:37:08 PM by Void »

Tomtech29

  • Sr. Member
  • ****
  • Posts: 447
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12170 on: February 15, 2016, 10:01:50 PM »
"Void"
better that I did not specify .

-Power consumption of kacher: 24 V  1.8-2 A
-Totaly 260w and When kacher run Power consumption totally 9-10A(24V) is to strengthen the long way:D
question to:"Verpies"
...of the Tl494 I mean some unusual combinations or something that kind of shift in phase how you want it done?

-or Itsu already has a finished project with a double primary winding yoke?

Void

  • Hero Member
  • *****
  • Posts: 2333
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12171 on: February 15, 2016, 10:16:48 PM »
"Void"
better that I did not specify .
-Power consumption of kacher: 24 V  1.8-2 A
-Totaly 260w and When kacher run Power consumption totally 9-10A(24V) is to strengthen the long way:D

Plugging the light bulbs directly into a mains socket is just as effective, but much simpler. :)

URFA

  • Jr. Member
  • **
  • Posts: 70
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12172 on: February 15, 2016, 10:35:51 PM »
Hi Geo and all.
First of all I want to say, I have not had time to develop my setup.Sadly, I would say that my setup did not OU %100. But my setup had the a chance. I haven't a osciloscope. You can not succeed this system without oscilloscope. "URFA also mentioned that he saw no effect from connecting earth ground when he was running from batteries" My setup can run hot end of the grenade and only ground.(when running from bateries) And when kacher run, the effect is do  %100.
1 year ago I run 420w brightness of bulbs %100 full and with 24V 11A(With kacher). And I measure output voltage 190V 2.2A.I could not record a video. I want to say something friendly.I ruin the my setup, while trying to improve. I changed secondary of the kacher and inductor coil then I could not get strong effect. After I did a lot of experimenting.But I did not get strong effect like my first setup.Frequency of the Kacher is very important.I was not working on this system for a long time.My advice to you,if you have not the an oscilloscope,do not waste your time with my setup. I found random frequency harmony and after I lost effect when I editing my setup. Now I ordered some electronic materials and I will work on other system again.

Geo: I used Akula Pushpull Circuit from his first device in my setup. The scheme below. My Friend I advise you work on the system of the Alexee Sergey.I believe that his system will work.And it's easy and understandable explanation.

Good luck everyone

Regards

Ibrahim.

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12173 on: February 15, 2016, 11:22:04 PM »
"Void"
better that I did not specify .

-Power consumption of kacher: 24 V  1.8-2 A
-Totaly 260w and When kacher run Power consumption totally 9-10A(24V) is to strengthen the long way:D
question to:"Verpies"
...of the Tl494 I mean some unusual combinations or something that kind of shift in phase how you want it done?

-or Itsu already has a finished project with a double primary winding yoke?


TT, yes,  see this post for a screenshot:

http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg460729/#msg460729

Follow the 2th link there to way back to see more about this.

Itsu

Void

  • Hero Member
  • *****
  • Posts: 2333
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12174 on: February 15, 2016, 11:33:08 PM »
My setup can run hot end of the grenade and only ground.(when running from bateries) And when kacher run, the effect is do  %100.

Hi URFA. What I was referring to was based on what you stated here previously in regards to
earth ground not improving the performance of your setup in any significant way:

"I think it is not necessary connected to earth (To my way of thinking ) I don't any different effect when I connect it to ground."
http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg423137/#msg423137

"I have effect of the ground now in my experiments.  But when my power supply connected to the network effect is bigger. And when I use battery,the effect of the ground verry little."
http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg422658/#msg422658


1 year ago I run 420w brightness of bulbs %100 full and with 24V 11A (With kacher). And I measure output voltage 190V 2.2A

Previously you stated:
"In my setup.
Power consumption of kacher: 24 V  1.8-2 A
Power consumption of push pull driver circuits: Without kacher 24V 2A but I measured when kacher runing Its power consumption is growing about 24V 7-8 A.
Power consumption of kacher and push pull driver totally 9-10A(24V)
I have 4x40w and 1x100w  220v light bulbs. Totaly 260w and When kacher run they are fully brightness.
My setup not OU.I only share this video with you to show the effect of Kacher. I'm still working on this system like you."
http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg421773/#msg421773

I guess you are you talking about a different test later where you powered 420W of light bulbs?
If you really measured 190V at 2.2A (potentially around 418W, i.e.  if no phase angle) to the light bulbs, with 264W input power consumption, then yes,
that would an interesting result. Were they all filament type light bulbs, or were some of the lights other types?
Were you powering from a battery or mains connected power supply?


My Friend I advise you work on the system of the Alexee Sergey.I believe that his system will work.And it's easy and understandable explanation.

Where can info be found on Alexee Sergey? His name sounds familiar...

All the best...

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12175 on: February 15, 2016, 11:43:18 PM »
https://www.youtube.com/watch?v=bXwfFV4DIyk 
Published on May 3, 2015
* Push the lamp from the pool is not 60V, and 95V .. (Well I vskidku said that .. 60V)
* c high-voltage part, somewhere around 190-200V, but the system is not configured, assembled to show you the effect of HV ..

Dont get too hooked on this one, and read the comments on the page.

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12176 on: February 16, 2016, 12:56:49 AM »
   Urfa.
    You removed your video???

URFA

  • Jr. Member
  • **
  • Posts: 70
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12177 on: February 16, 2016, 01:01:55 AM »
   Urfa.
    You removed your video???

Yes, I removed.Because  I don't want to be misleading. That video is not important.

URFA

  • Jr. Member
  • **
  • Posts: 70
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12178 on: February 16, 2016, 01:05:40 AM »
Hi URFA. What I was referring to was based on what you stated here previously in regards to
earth ground not improving the performance of your setup in any significant way:

"I think it is not necessary connected to earth (To my way of thinking ) I don't any different effect when I connect it to ground."
http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg423137/#msg423137

"I have effect of the ground now in my experiments.  But when my power supply connected to the network effect is bigger. And when I use battery,the effect of the ground verry little."
http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg422658/#msg422658


Previously you stated:
"In my setup.
Power consumption of kacher: 24 V  1.8-2 A
Power consumption of push pull driver circuits: Without kacher 24V 2A but I measured when kacher runing Its power consumption is growing about 24V 7-8 A.
Power consumption of kacher and push pull driver totally 9-10A(24V)
I have 4x40w and 1x100w  220v light bulbs. Totaly 260w and When kacher run they are fully brightness.
My setup not OU.I only share this video with you to show the effect of Kacher. I'm still working on this system like you."
http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg421773/#msg421773

I guess you are you talking about a different test later where you powered 420W of light bulbs?
If you really measured 190V at 2.2A (potentially around 418W, i.e.  if no phase angle) to the light bulbs, with 264W input power consumption, then yes,
that would an interesting result. Were they all filament type light bulbs, or were some of the lights other types?
Were you powering from a battery or mains connected power supply?


Where can info be found on Alexee Sergey? His name sounds familiar...

All the best...

Hi Void.
Hopefully I can express myself in English.
I made many experiments. I tried sometimes ridiculous experiments.Sometimes I have tried many different things from Ruslan's(Akula) system.
So I got very different results.I did not write them all here.Some of my experiment did not influence the ground.
But the grounding had an impact in some my experiments. Many times was greater the input power than output power.
But I obtained 24V 11A input and 190V 2.2A output. I did different experiments for higher output power.But after I changed my setup, I could not achieve the same results in a more. Because I was constantly making changes my setup.I used filament type light bulbs in my all experiments.
I burn nearly the 20 power supply in my experiments. I sometimes use battery and sometimes grid.In both I used.

About Alexee Sergey. He is succesfull Ruslan-Akula setup. No more information is currently about him on the
Internet.Information deleted. GeoFusion shared his scheme on this forum.
I attack some of Sergey's picture and schemas.

İbrahim

URFA

  • Jr. Member
  • **
  • Posts: 70
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #12179 on: February 16, 2016, 01:11:02 AM »
Sergey's Setup