Author Topic: Kapanadze Cousin - DALLY FREE ENERGY (Read 11802954 times)

John.K1 · « **Reply #11685 on:** January 24, 2016, 12:28:48 PM »

That sucks. I made a long message with video references and translations etc.- It took me 1/2 hour to make it and when I clicked the save button all is lost due to time Log out.

Ok sometime next time.

Tomtech29 · « **Reply #11686 on:** January 24, 2016, 03:16:29 PM »

suggest that the scheme need to use:(enter it here)
I confused

Quote from: magpwr on January 23, 2016, 01:22:15 PM

hi Tomtech29 and everyone,

I have attached waveform and circuit diagram as downloaded from the huge torrent related to Sergey.
The circuit diagram was only revealed for a brief moment in one of the Russian video discussion as found in the torrent download.

2 things to note
1)Base on waveform sergey is using 1/100 ratio for the frequency.If the tesla frequency 1.66Mhz the pwm frequency is 16.663khz.The only thing i can't tell if the frequency in Mhz is derived from interrupter pulse ,harmonics or just tesla frequency.

2)Sergey circuit although i got no time to study this it would be likely generating few interrupter pulse say 5...9pulse in a row.
If you are familiar with tesla coil and interrupter circuit.I think Sergey is running this interrupter pulse at tesla coil resonance but using only 5...9 pulses in a row,in nanosecond.
"Like he is aiming for nearly maximum point and not going further."

Oleg circuit merely generate single nanosecond pulse compared to Sergey's circuit.

But i do find it strange Sergey's circuit did not Superimpose high frequency in Mhz to center tap.Worst there is no choke implemented.Maybe this was his early design.

-----------------------------------------------------------------------------------
My last experiment with "Tesla Transponder 2.0" circuit with interrupter pulse (10...20pulse in a row)without kapanadze coil yield max 32Amps to Earth .Power using full bridge rectifier from a high power 12 to 220volts inverter.
Interrupter circuit does produce little better output at a cost of increased current draw.

---------------------------------------------------------------------------------

All the while my primary aim without dabbling further was just to get some spark from the ferrite rod which i had failed miserly."This was the test Akula did before even providing power to the bulbs in the old video"

After watching the recent video of Geofusion.This gave me hope to complete this feat successfully at least. .

I have no such experience in building PCB and I have so far not managed to put together even one efficient controller to Tesla!
I care that it was such scheme in such form as above where I know where paths ( strange Sergey's circuit ) drawn with pen does not appeal to me!
I know it may seem ridiculous,these logic gates-background checker:D
-I would like to make a controller that could perform several experiments on the Tesla coil .
You suggest that a good start is a single pulse Ok.
would you how to control this Tesla? where should I start / guys suggest unipolar?
-pulse packages or single?
Thank you all.

John.K1 · « **Reply #11687 on:** January 24, 2016, 03:35:36 PM »

Hi Tom

About the pulses- start with this info. Think about train of pulses.probably unipolar pulses. Ruslan shows a difference of this pulses between in phase and out of phase with the current wave. I think he says he takes a picture of pulses from the gate of his transistor. That video was here already but is not any more on YouTube.

https://www.dropbox.com/s/p064duendpvhowy/%D0%AD%D1%84%D1%84%D0%B5%D0%BA%D1%82.mp4?dl=0

Dog, Jeg other- in short what I wanted to write before. If the grenade coil is wound as a normal transformer, how do you inductively de-couple between the current coil? How should current coil be wound like? In other word- how to wide bifilar with one wire? It confuse me.

Thanks.

NickZ · « **Reply #11688 on:** January 24, 2016, 04:22:38 PM »

Since no one has managed to see any amplification effect (OU), from the simple Kacher circuit, or winding the grenade coils in either way. Why would you want to make the much more complicated pulse train system for the Kacher?
Get it working, first, like Ruslan showed as a simple Kacher crt, then make the more complicated set up, once you have the Kacher circuit working. Not before, like you're all trying to do. Or you may get stuck, where you all are right now. Burning out components, and going no where.

We need to start simple. It took several years to perfect this all to the point it is being shown now. Thanks to Oleg, and Ruslan.
But, we still aren't seeing or obtaining the desired "effect", at all.

Geo: You're partially lighting less than 100w worth of bulbs while using a 360 watt PS.
If the effect is to happen, we need to show it lighting more bulbs than the input power that is being provided for.

I don't see any Magic in the mediator, as it is not working as a normal choke, and allowing more current to pass into the circuit, and burning out the fets, or overheating components.
I found my green toroid, but it is not as big as yours. Only about an 1 1/4 inches, or so. I had it mounted onto the device, to see the current wave form of the grenade. I'll try that core out next, once I get my device working again.
I've replaced the fets, and it still won't fire up. I still don't know what's up with that. The strong vibration from the yoke killed more than just the fets. Beware!!!

Hoppy · « **Reply #11689 on:** January 24, 2016, 05:01:24 PM »

Quote from: NickZ on January 24, 2016, 04:22:38 PM

We need to start simple. It took several years to perfect this all to the point it is being shown now. Thanks to Oleg, and Ruslan.
But, we still aren't seeing or obtaining the desired "effect", at all.

Nick,

I was of the understanding that Geo has seen the desired effect. Although you say that Geo is using a high powered supply, he / we do not yet know how much power his PSU is supplying, or how much power his load is consuming. His next video should shed some light on this as he says he will be taking measurements. Don't assume that a 360W PSU is actually delivering 360W or anywhere close to its rating to Geo's device. I get the distinct impression that you still do not understand power.

Your mosfets are most likely being destroyed by high voltage, not current through the introduction of the mediator.

Tomtech29 · « **Reply #11690 on:** January 24, 2016, 05:59:05 PM »

Hi. NickZ
you ask why I wade further with a complex system, I believe that the circuit Kacher is just an example of how to find the pulse point.
there is no system using a looped.
so really the power that we have the same reservoir LC It is not comparable to the example Ruslan! It fires from the yoke of 650 Watts without reinforcement!
It is more efficient!
What is behind the winding inductance type grenade?
-now we use resonance to until extinction/I do not understand what it's like for him that does not happen?
the second thing is to maintain the resonance to be out of tune.
The pulse system is second to none I would like to come up with what to do with these impulses / He conducted an experiment on different types of coils
and I found that the pulses appear after bridge rectifier at the output of coil but this arrangement inductive (I connected the same yoke 28 directly to the inductor) using ZVS the capacity of the inductor 28 closes rotation I observed considerable power! at 8kHz. and connected the output of the second coil is on the bridge appears in DC and beyond the high-voltage rock peaks!
Now the :"Dog one" He showed me that mustache on top of the current! More Kacher will not help because you will only see the effect of increased tension! and as the voltage is reversed magnetic field of the inductor?
you find that to insist but one of the oscilloscope line video can be seen opposite the bell!
still I do not know how this bell to get on Tesla?
Primary Dally is based on pulsed and that to hold that!
(he was so short material to align Kacher and pulses at the base of transistor le not show what is happening on the air signal penetrating into the tank :

)

Jeg · « **Reply #11691 on:** January 24, 2016, 06:13:02 PM »

Quote from: John.K1 on January 24, 2016, 03:35:36 PM

Dog, Jeg other- in short what I wanted to write before. If the grenade coil is wound as a normal transformer, how do you inductively de-couple between the current coil? How should current coil be wound like? In other word- how to wide bifilar with one wire? It confuse me.
Thanks.

John, a coil with two opposite direction layers can be called as a current coil only when using it as a choke and not as a secondary like grenade is. This is because when you inject a signal through it, voltage is being canceled out between the opposite turns, so there is not any significant magnetic field to the choke and so current passes free with no drag.

Looking from my mistakes the last couple of years, I now think that there is not any real reason to have my grenade opposite wounded. In fact now that I see the device as a Bemf gen, one direction winding will give higher bemf peaks. Simple logic.

May I ask something? Is anyone here that have tuned his inductor coil to the same frequency like grenade? If not, then why do you care about related wavelength for inductor?

Jeg · « **Reply #11692 on:** January 24, 2016, 06:33:26 PM »

In other words. If inductor is to be tuned in series with a cap at low KHz, why does it need to be wavelength related with grenade?

John.K1 · « **Reply #11693 on:** January 24, 2016, 06:48:50 PM »

Quote from: Jeg on January 24, 2016, 06:33:26 PM

In other words. If inductor is to be tuned in series with a cap at low KHz, why does it need to be wavelength related with grenade?

Hi Jeg, it is actually coincidence as I spot the answer for your question in Ruslans video today. In some of his last vidoe he says the granade can have any frequency what ever capacitor you use (if I right understood -Russian is not my native language

) He says important is to get a synchronization between Tesla and current LC loop.

If this can help.

Edit1:

So if I right understund my Grenade coil will be like a normal wound like a normal transformer - how is normal ransformer wound? Back and forward? That what he show with his finger -right? So the direction of my first layer will be a reference for opposite direction of current coil?

As very important he see the effect of the increasing of magneic field due to HV pulse. That's what is the last video about . He says the pulses in anti-phase does the effect. I do not see it-I do not know what should I look for as both -in phase and anti-phase they looks similar. Check the increase of frequency when he fires pulses. It increase almost double.

Jeg · « **Reply #11694 on:** January 24, 2016, 06:55:28 PM »

Quote from: John.K1 on January 24, 2016, 06:48:50 PM

Hi Jeg, it is actually coincidence as I spot the answer for your question in Ruslans video today. In some of his last vidoe he says the granade can have any frequency what ever capacitor you use (if I right understood -Russian is not my native language ) He says important is to get a synchronization between Tesla and current LC loop.

If this can help.

Thanks John. What do you think that sync means? I know that when we interest about specific wavelength in a coil, then it is because it has to be able to vibrate at this frequency. Can your inductor ring at this MHz frequency?

John.K1 · « **Reply #11695 on:** January 24, 2016, 07:14:02 PM »

Quote from: Jeg on January 24, 2016, 06:55:28 PM

Thanks John. What do you think that sync means? I know that when we interest about specific wavelength in a coil, then it is because it has to be able to vibrate at this frequency. Can your inductor ring at this MHz frequency?

Jeg, I think as I said in my previous edited answer, the important is to increase the magnetic field by firing the HV pulses (that's what he says). I am not sure about it. Not sure how can pulse increase magnetic field. Maybe it can. My opinion is more like electrons accelerator?

He calls antenna a Plate of capacitor. Exactly as some of us here - forming Asymetrical capacior.

Why MHz on inductor? There should be KHz range -no?

nelsonrochaa · « **Reply #11696 on:** January 24, 2016, 07:17:49 PM »

Quote from: Tomtech29 on January 24, 2016, 05:59:05 PM

Hi. NickZ
you ask why I wade further with a complex system, I believe that the circuit Kacher is just an example of how to find the pulse point.
there is no system using a looped.
so really the power that we have the same reservoir LC It is not comparable to the example Ruslan! It fires from the yoke of 650 Watts without reinforcement!
It is more efficient!
What is behind the winding inductance type grenade?
-now we use resonance to until extinction/I do not understand what it's like for him that does not happen?
the second thing is to maintain the resonance to be out of tune.
The pulse system is second to none I would like to come up with what to do with these impulses / He conducted an experiment on different types of coils
and I found that the pulses appear after bridge rectifier at the output of coil but this arrangement inductive (I connected the same yoke 28 directly to the inductor) using ZVS the capacity of the inductor 28 closes rotation I observed considerable power! at 8kHz. and connected the output of the second coil is on the bridge appears in DC and beyond the high-voltage rock peaks!
Now the :"Dog one" He showed me that mustache on top of the current! More Kacher will not help because you will only see the effect of increased tension! and as the voltage is reversed magnetic field of the inductor?
you find that to insist but one of the oscilloscope line video can be seen opposite the bell!
still I do not know how this bell to get on Tesla?
Primary Dally is based on pulsed and that to hold that!
(he was so short material to align Kacher and pulses at the base of transistor le not show what is happening on the air signal penetrating into the tank :)

Finaly someone put brain work ! 😀 i sad months ago that same effect could be reproduced without
Ruslan coil configuration ... Is not the coil but the effect .
But well, people just copy .. But if stop a bit to think by own maybe it could achive better results but well , maybe this área of research is not to everyone 😉

Jeg · « **Reply #11697 on:** January 24, 2016, 07:33:36 PM »

Quote from: John.K1 on January 24, 2016, 07:14:02 PM

Why MHz on inductor? There should be KHz range -no?

I see that vibrates at KHz due to series resonance. But even if it wasn't wavelength related to grenade, then again it would be able to vibrate at KHz due to the series resonance. There is not any sense for inductor to be wavelength related to grenade if it wasn't be for vibrating at MHz. Don't you see the hole??

Tomtech29 · « **Reply #11698 on:** January 24, 2016, 07:33:38 PM »

hi
"John, a coil with two opposite direction layers can be called as a current coil only when using it as a choke and not as a secondary like grenade is. This is because when you inject a signal through it, voltage is being canceled out between the opposite turns, so there is not any significant magnetic field to the choke and so current passes free with no drag."
some truth in this is ,once I tested a simple coil in the same direction I had weaker results! (I had the impression that when the load coil is greater toll on the disadvantage LC) This means the load grenade and inductor gets ass

NickZ · « **Reply #11699 on:** January 24, 2016, 07:51:19 PM »

Jeg:
That's why it has to be a harmonic of it, and not the same frequency. As the induction circuit of the 3 turns coil. won't reach the same Mhz frequencies, with the recommended windings, and doesn't need to, anyway. But, in any case the Kacher circuit won't do much at higher Mhz frequencies. Like 2.6Mhz, or higher.
I think that Itsu gave something like that a try, (same frequencies tests), but I don't remember how it all went.
Maybe he can explain it better.

Hoppy: Lighting up a bulb or bulbs with more than their needed input power from a PS, does not really show an "effect"?
The effect should produce more that what the input source provided can provide. Or not? So, place more than 360w worth of bulbs on it, not 100w.
I'm not assuming anything, as yet. One way or the other.
But, I'd like to see more output from a device than what a PS can provide to it, as proof of anything.
I still don't get the OU, part. As it has been mentioned that in order to see an effect, that will allow a device to self run, first, it has to provide more power out, than in. Not just a brighter 100w bulb, that is still not fully lit, by the 360w supply. Even the measurement won't be enough for me, that in itself is not enough, to show the needed effect. Self running will do it though.

However, I'm not knocking what's been shown, and do appreciate it. And, I'm also waiting to see what the long term effects of the mediator (mixing voltage with current) in that way will do to the device and it's components.

I still can't get mine to fire up again. After is went into the vibration mode, like you like to see.
I should of made a video of it. The vibrating dance of death.
Somewhere in my device there is still a short circuit, but things look ok, so far, I haven't been able to find it yet.
I've replace both fets, and there's still something shorting out. I'll get it though...

News:

User Menu

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY (Read 11802954 times)

John.K1

Re: Kapanadze Cousin - DALLY FREE ENERGY

Tomtech29

Re: Kapanadze Cousin - DALLY FREE ENERGY

John.K1

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

Hoppy

Re: Kapanadze Cousin - DALLY FREE ENERGY

Tomtech29

Re: Kapanadze Cousin - DALLY FREE ENERGY

Jeg

Re: Kapanadze Cousin - DALLY FREE ENERGY

Jeg

Re: Kapanadze Cousin - DALLY FREE ENERGY

John.K1

Re: Kapanadze Cousin - DALLY FREE ENERGY

Jeg

Re: Kapanadze Cousin - DALLY FREE ENERGY

John.K1

Re: Kapanadze Cousin - DALLY FREE ENERGY

nelsonrochaa

Re: Kapanadze Cousin - DALLY FREE ENERGY

Jeg

Re: Kapanadze Cousin - DALLY FREE ENERGY

Tomtech29

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY