Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11719168 times)

Tomtech29

  • Sr. Member
  • ****
  • Posts: 447
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11640 on: January 19, 2016, 09:53:53 PM »
Hi Guyz :)

Yes, What I really want is for us to put our heads together,
we are so close to know how the device works, yet for what I managed up till now.We need to do further testings on this.

   Jeg, :)
yes, I will see where I could get  analog meter Volts and amps both Dc and Ac for the further tests.

  Hoppy,
Yes measuring equipments to continue to see differences, will make sure to get them asap.

 Tomtech29,
Hi there x), Yes amp analog meter is needed for measurements, I drew a schematic for you too see. down.

  Nick,
24V is fed to  Kacher input. As well PushPull. you will see in Diagram Edited on how I have everything hooked up.
Look at the Mediator connections and where effect takes place. follow the lines carefully, and see where I have it striped as example if tested.


Below here I have what is currently hooked up now. Today I will Continue with Experimentation.
Output is HV DC!!   it can be Done connecting Load to the AC lines
but DC line has better output with the proper Bipolar capacitors.
Sometimes I Have no idea what I'm expecting or what connections I might make, but It's Doing Something Exciting! :)

https://www.youtube.com/watch?v=7ELg1TclytM

            Cheerz~
hi Geo.
I do not quite understand this bridge rectifier is connected from  the positive side  (+) to the emitter of the transistor???
rather strange that this is an NPN transistor or indeed so you have connected? (Please check this 100%)
(if so is it with this voltage measurement will be difficult to Karcher ordinary tester) HV!
-Besides, if the transistor is closed, the voltage returns to the yoke on the primary windings, there appear peaks can be on one side of the transistor and therefore is one side heats up (I do not know whether the other party is able to level the playing field work) such a high voltage that you will be hard to measure pulse power Kv!!!
I have a question, or when the detachable bulb appears high voltage arc? (be careful I would not become foot on the ground) :D:


NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11641 on: January 20, 2016, 01:33:38 AM »
    Tomtech:
   I have been connecting the Kacher transistor emitter, to the 0.47uf, 2000v capacitor. To one side of the cap, or the other depending on other connections. This cap is also connected to my Earth ground line. This increases the kacher's output, some how, over what it can do normally.

   So now, I've connected my older 12 yoke from the previous tests to serve as a "mediator". As it had a total of 12 turns (6 and 6), on the primary coil, and about 22 turns on the secondary. I still need to finish some connections, and then to fire it up. We'll see what that does. At least for now, I can see that my previous yoke chokes which have been replaced by this big yoke core, instead, now, the big yoke is NOT heating up, like the smaller chokes normally do.
  More to come...

N20Wolf

  • Newbie
  • *
  • Posts: 17
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11642 on: January 20, 2016, 12:44:43 PM »
Hello! Torrent, to download files over the fuel-less generator Sergey Alexeew. Click here, to download СКАЧАТЬ/DOWNLOAD: https://yadi.sk/d/JSDrPu5BnNvbM

Author this Generator: my.mail.ru/mail/alexeewsergey/ , plus.google.com/u/0/100666972159221696809/posts

Video: m.my.mail.ru/mail/alexeewsergey/video/_myvideo/11.html

email: alexeewsergey@mail.ru

Forum: http://realstrannik.com/forum/freeenergylt-antanas/708-povtorenie-ustanovki-free-energi-kolobukhova?limitstart=0

Tomtech29

  • Sr. Member
  • ****
  • Posts: 447
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11643 on: January 20, 2016, 01:51:27 PM »
    Tomtech:
   I have been connecting the Kacher transistor emitter, to the 0.47uf, 2000v capacitor. To one side of the cap, or the other depending on other connections. This cap is also connected to my Earth ground line. This increases the kacher's output, some how, over what it can do normally.

   So now, I've connected my older 12 yoke from the previous tests to serve as a "mediator". As it had a total of 12 turns (6 and 6), on the primary coil, and about 22 turns on the secondary. I still need to finish some connections, and then to fire it up. We'll see what that does. At least for now, I can see that my previous yoke chokes which have been replaced by this big yoke core, instead, now, the big yoke is NOT heating up, like the smaller chokes normally do.
  More to come...
NickZ
we assume that the emitter is connected to the negative side power supply GND and an additional ground is contrary to what he said that we should not ground the power supply!
It implies that this scheme is flawed.
-but rescue us new message arrives :link containing recorded conversations with :Ruslan,not fully reveals the secrets and turns?
could do with a good translation!

I understood something about the yoke that is in two parts between them is "something" possible piece of paper ,still says something about the yoke do not know whether it is: horizontal tape as it happened as it did with Lithuania experiment!


Tesla coil control is required # 2MHz system,it's really just the LC tank does not play any role first!

the video footage shows that the longer someone replicates the system fully looped and interesting effect of working with a note "Karcher": silent on such power

but it makes mixes this frequency to tune in Radio :D (sound from the yoke sounds like noise from the speaker) chaotic's not a squeak?
very interesting touches and moves the coil and you can hear how the system adjusts itself!
-To get more power at the output must be replace "Karcher"  used this pulsar Ns.

not all the words were spoken I realized that someone had already done are not published on the Internet or have any pressure from the Mount of power afraid to spread the word or simply they want to only have it for themselves?!.
Now is the moment of euphoria, guessing who will do the correct configurations?.
Please share it what have you discovered...


Tomtech29

  • Sr. Member
  • ****
  • Posts: 447
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11644 on: January 20, 2016, 05:17:20 PM »
Hi.
I have a question for you is this chip can replace the CD4011, for example 74Ac00?
 and the second is related to the push-pull (as the second transistor opens without signal The input to the driver mosfet?

Dog-One

  • Hero Member
  • *****
  • Posts: 1019
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11645 on: January 21, 2016, 12:50:51 AM »
Hello! Torrent, to download files over the fuel-less generator Sergey Alexeew.

Not finding any seeders at the moment.

Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11646 on: January 21, 2016, 08:36:19 AM »
Hi Itsu
(Allega's blue box)

I was wondering how did you drive 74HC00 by taking the 12V pulse output of 494, and feeding with that the 5V input of the CMOS. Did you use any kind of transistor, transforming 12V to a 5V pulse?
Did you make it  by resistor divider ( R2,R4)?

Tnks

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11647 on: January 21, 2016, 10:34:01 AM »
Zero point energy, where does it come from ? is it background energy from when the earth was created or is it constantly being created (thus making the conservation of cosmic energy necessary) ?

Dr Thorsten Ludwig - Zero point energy, The view point of modern physics on the sea of energy

Well watch this and find out !  https://www.youtube.com/watch?v=bCvbqMGPpa8


itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11648 on: January 21, 2016, 11:15:28 AM »
Hi Itsu
(Allega's blue box)

I was wondering how did you drive 74HC00 by taking the 12V pulse output of 494, and feeding with that the 5V input of the CMOS. Did you use any kind of transistor, transforming 12V to a 5V pulse?
Did you make it  by resistor divider ( R2,R4)?

Tnks

Hi Jeg,

no, i did not use anything else then whats in the blue box, so i guess the R2,R4 and/or the 1n4148 diodes are taking care for that.
The output of my little TL494 circuit feeds into 2 MOSFET drivers (UCC37322) and are also fed at that point (via a switch) to the blue box.
I don't know right now what level of output that TL494 circuit has.
By the way, i am using a 74HC132

Itsu

« Last Edit: January 21, 2016, 05:08:31 PM by itsu »

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11649 on: January 21, 2016, 02:13:27 PM »
  So, I made a "mediator" coil out of my older 12v Tv yoke from the previous tests. It has 12 turns on one coil, and 22 turns on the other side of the yoke coils.  I don't notice any benefit from taking the Kacher's circuit input from the 22 turns coil side of the yoke core, and also not much from the 12 turns side, either. But, my regular 24v yoke is not able to go into the chaotic mode now. And my two mosfets are heating up. One fet more than the other.  Like Geos do. Although the big mediator choke is not heating up, like the smaller chokes that I had on before did.
  However, there does seam to be a higher degree of sync with this set up, between my Kacher, and the induction circuit. But, I need more time to tune the device, using tuning caps, to see IF there's any additional output at the bulbs. 
In any case, I need some more time to work on all of this, to see any real "effect". 

  BTW: I do have one of those 1 1/2 inch green toroids, but I can't find it right now. I tried a smaller green toroid, also, but it heated up too much.

  EDIT:  The device started up into a strongly felt "Vibrating" mode. And I let it run in that mode for a minute or two. until one of my fets started to smoke. Of course now the device does not start, at all. I'll replace that fet, and try not go into that mode again, at least not for longer than a few seconds.
  What is the value of the diode that is to be use at the PS?  10A??? 

   Any one else working on this mediator coil set up?

Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11650 on: January 21, 2016, 03:46:28 PM »
Hi Jeg,

 R2,R4 and/or the 1n4148 diodes are taken care for that.

You are very right. Thanks a lot ;)

GeoFusion

  • Sr. Member
  • ****
  • Posts: 449
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11651 on: January 21, 2016, 08:51:04 PM »
Hi there Guyz :).

Had no time to work on the Davice last days, had some matters to take care of. will see If I can get some time on it Today.
My WIMA caps 2000V 0.47 reached :). and  radio material to make into a Spirit Radio finally.
I recently Downloaded a 1.70Gb file from russian Forum.thnk you N20Wolf for links.  I could Upload some to the forum.
Torrent Links

http://realstrannik.com/forum/freeenergylt-antanas/708-povtorenie-ustanovki-free-energi-kolobukhova?limitstart=0

From a Latest update of a person which replicated the device In the same manner as How Akula has his schematic :).

is Sergey :)
He replicated the system, The schematic he drew is so similar as Akula's but easier to understand. 
I see now where and how the Effect takes place and I Did not expect what I saw, but it's Brilliant!
The Mediator is the Ferrite YOKE ( any round transformer core )with high Perm.!
With proper connections on the Circuit board of Push-pull and Tesla Nano-sec Gen. and of course
High Voltage capacitors are needed for the effect to take place.
Makes sense now while taking a look at the Schematics and Videos ( High Quality close ups ). at the same time.

Like I said befor guyz, this system is combining External Voltage and External amps to combine together. to form many watts.
Radiant Fusion Generator I would call it.


   Nickz,
The Value of the Diode I used at the power supply is 1N5408, 1000V 3A.
Srry to hear about the smoked Fet. Btw try to find the 1 1/2 inch Toroid, maybe there will be a difference. I soorted out my Fet problem.
But Nick, make sure you have Atleast a TL494 circuit or what Sergey has or Oleg boards. for tuning you will need it.
How do you connect the 22T coil for kacher? Both Negative and Positive leads of the kacher to the 22T coil of mediator?
Or just 1 lead of the 22T to Kacher positive and the negative to the PS?

Tomtech29,
Yes exactly how you see it in the schematic I had it connected just like that.
but changed the Emitter connection to the ground side and saw better effect.
Btw the Voltage at output is 102 Volts, i managed to measure it. but will eat when putting more load,
because the system doesn't have a good high voltage cap yet.

magpwr,
Yes Vasmus System is very different in setup compared to Akula/Ruslan devices, especially the sumator Core is something.
yes kacher is powered by one of the outputs of the sumator coils the nano crystalline plated coiled up core.
I thinking the sumator with the mixing circuit is the Mediator. yes it's like mixing.
Kacher and coiled plate pulser, as you can see they are similar components in these systems

   
        Cheerz~

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11652 on: January 22, 2016, 01:56:04 AM »
  Geo:
   I was also busy today and haven't taken the time to work on my device.

   You asked, "How do you connect the 22T coil for kacher? Both Negative and Positive leads of the kacher to the 22T coil of mediator?
Or just 1 lead of the 22T to Kacher positive and the negative to the PS"?
                                                                                       end quote.

   The ending of the 22T coil on my mediator is not connected to anything,  as it only dimmed the Kacher's output, not brighten it.
The end of the 12 turns coil of the mediator goes to both the Kacher transistor's positive rail, and also to the yoke center tap.
The PS is the negative for both Kacher and the yoke circuits.
  I still need to tune, and adjust things though, once I get it all working again.
  I did notice some kind of sync going on, but would lose it, like as if there wasn't enough power to sustain it.
Also, at times this strong magnetic vibration from the yoke.
 And, now I can't get into the "chaotic mode", anymore. So, I'm probably not hitting the right resonant point, yet. 
I need more tuning caps in anycase,  but which ones?   
  I'll take another look for my 1 1/2 inch green toroid core. Or I'll just  use a smaller yoke with the 12t, and 60t like is recommended.

   Good idea about the yoke being the mediator... 
   A yoke with a full circle of thick mag wire, then all the other coils wound on top of that.
 I wound a yoke like that at one time, but didn't connect the Kacher up to it, as you're doing.

Dog-One

  • Hero Member
  • *****
  • Posts: 1019
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11653 on: January 22, 2016, 02:24:49 AM »
I recently Downloaded a 1.70Gb file from russian Forum.thnk you N20Wolf for links.  I could Upload some to the forum.
Torrent Links

http://realstrannik.com/forum/freeenergylt-antanas/708-povtorenie-ustanovki-free-energi-kolobukhova?limitstart=0

From a Latest update of a person which replicated the device In the same manner as How Akula has his schematic :).

is Sergey :)
He replicated the system, The schematic he drew is so similar as Akula's but easier to understand. 
I see now where and how the Effect takes place and I Did not expect what I saw, but it's Brilliant!
The Mediator is the Ferrite YOKE ( any round transformer core )with high Perm.!
With proper connections on the Circuit board of Push-pull and Tesla Nano-sec Gen. and of course
High Voltage capacitors are needed for the effect to take place.
Makes sense now while taking a look at the Schematics and Videos ( High Quality close ups ). at the same time.

I finally downloaded the torrent and will continue to seed it for others that may want to investigate.  The schema
looks remarkably simplistic.  There is a hand drawn color highlighted schema that should prove most useful as well
as a new schema computer generated (January 2016).  Be cautious of this new schema as I found a few mistakes
in it already--one being the implementation of the LM2596, which looks to have the output inductor and feedback
mechanism backwards.

The older hand drawn schematic shows all the coils and antenna wound in a clockwise direction except for the last
two segments of the grenade coil.

It does look as though Sergey is working towards a single circuit board solution requiring only the hookup of the large
or power heavy components.  From what I can see, you will only need to connect the power transistors, toroid coil,
high voltage capacitors, diodes and the main coils to have a fully functional system.

I'm still concerned about why all these replications are using massive heatsinks and fans.  Like Nick has mentioned,
if properly sized and tuned, the transistors should be able to run with passive heatsinks just fine.


Like I said befor guyz, this system is combining External Voltage and External amps to combine together. to form many watts.
Radiant Fusion Generator I would call it.

I found this quote stating a Method of Operation:
Quote from: Anton Dremliyga (AntonW)
Key to the scheme:

There choke coil through which a current is passed to the transformer.  This current creates on reel-throttle
electromagnetic field with salient pole like a permanent magnet, the North and South if the North apply an
electrostatic field, the current consumed by the load will increase from 1A to 3A, if the electrostatic field to
submit the South, the current to 3A drops to 1A.  That is thus throws electrostatics in excess 2A, but
nevertheless these 2A consumed from the power supply.  If you submit a South magnetic field, the 2A that
throws an electrostatic field in the system will be compensated by the magnetic field coils supplied from the
South and not the consumption of 2A power supply.  As a result, the system consumes 1A, and the electrostatic
field and the magnetic field applied to the different poles of the coil-throttle will pop loose in extra 2A.

Explanation of the theory:

An atom of copper as a result of explosive impulses and influences MP pulls itself assume a charge in the
electrostatic field at the same time, the charge must be balanced by another similar charge, but opposite
in sign.  If at a given time will not be submitted to a magnetic field, electrostatic charge compensates the
magnetic charge with the power supply.  Since the magnetic field is applied with respect to a predetermined
time of submission of the electrostatic field, this process takes place synchronously.  and electrostatic charge
compensates for magnetic.  As a result, a copper atom and receives magnetic charge and the electric charge
is uniformly and pulls the magnetic charge from the power source.

https://www.youtube.com/watch?v=jOxdsFsJc7k

So I would have to agree Geo, we have a system that is mixing amperage and voltage from two different
sources giving us real output power.
« Last Edit: January 22, 2016, 08:58:56 AM by Dog-One »

Dog-One

  • Hero Member
  • *****
  • Posts: 1019
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11654 on: January 22, 2016, 08:46:45 AM »
This is something new, an antenna spark gap.  I wonder how much it helps...?