Author Topic: Kapanadze Cousin - DALLY FREE ENERGY (Read 11809789 times)

Hoppy · « **Reply #11055 on:** October 24, 2015, 06:28:48 PM »

Quote from: NickZ on October 24, 2015, 04:49:27 PM

Hoppy and Itsu:
I remember the increase in power that both you and Itsu had previously shown. HOWEVER, that is no where the same increase as what is being shown by this last Russian guy, (I forget his name).

Nick,

Incorrect. The increase was dependant on me tuning the Kacher with a ferrite rod, as that guy Ypok was doing. I could get the bulb really bright that way, up to almost 280V across the 240V rated bulb, bringing it close to blowing out! However, as mentioned before, this was at the expense of more supply current and therefore not the power amplification effect that T1000 is talking about.

Tomtech29 · « **Reply #11056 on:** October 24, 2015, 06:43:45 PM »

Quote from: itsu on October 24, 2015, 05:34:22 PM

Here a zoomed in screenshot of the firing of the kacher (purple) ontop of the current peak (green).
Gate pulse is at its maximum width and narrowing it down decreases the kachers amplitude
The kacher runs/rings at 1.28MHz, see top right purple delta data.

Regards Itsu

nice work if you can do something with this bell get sharp edges or high-voltage seen something on the bulb?
if you checked the performance of the winding 28 out?

itsu · « **Reply #11057 on:** October 24, 2015, 11:01:12 PM »

Taking a look at the kacher output with my HV probe (x1000).
I connected it to the open end of the antenna which will load the kacher to some extent presenting a lower frequency and amplitude, but it shows somewhat what we are up against.

Certainly no 26KV or wavefront peak as drawn by akula/ruslan....yet.

Regards Itsu

verpies · « **Reply #11058 on:** October 24, 2015, 11:34:48 PM »

Quote from: T-1000 on October 24, 2015, 05:51:40 PM

Introducing bigger cap lets you give more time for delay but also you need to be aware of catch 22 situation if your PLL trigger input is still on the peak of voltage. The time delay you set on pot will not match time delay between voltage and current peaks if the frequency will change too much.

You are correct but I don't see how the PLL could not be synched to voltage if it is transferring energy to the LC circuit (Grenade) from AC voltage sources (switched MOSFETs).

starcruiser · « **Reply #11059 on:** October 24, 2015, 11:37:52 PM »

Quote from: T-1000 on October 24, 2015, 05:51:40 PM

Hi itsu,

Introducing bigger cap lets you give more time for delay but also you need to be aware of catch 22 situation if your PLL trigger input is still on the peak of voltage. The time delay you set on pot will not match time delay between voltage and current peaks if the frequency will change too much.

I do not think so as the trigger signal is take from the drive signal from the PLL to the Fets for the 15Khz push/pull. SO if the frequency changes the pulse should follow. But you may be correct now that I think about it, but this would always be the issue anyways.

The issue I am concerned with is the fact the more capacitance means it should take a few more cycles to reach trigger point for the logic gates, i.e. t increases. this can be verified by probing the drive signal in the logic gate chain (see capture below) scope the output of the NAND gate against the drive signal, I figure we are seeing a multiple cycles to a signal to the next stage transition signal. like a 4:1 or something like that.

I circled the drive signal sample point after the 3.6k resistor and a blue circle after the second NAND stage.

starcruiser · « **Reply #11060 on:** October 24, 2015, 11:41:32 PM »

Quote from: itsu on October 24, 2015, 11:01:12 PM

Taking a look at the kacher output with my HV probe (x1000).
I connected it to the open end of the antenna which will load the kacher to some extent presenting a lower frequency and amplitude, but it shows somewhat what we are up against.

Certainly no 26KV or wavefront peak as drawn by akula/ruslan....yet.

Regards Itsu

I think this might be due to the hit and miss I mentioned above. Please take a look and let us know if this is indeed true. IF this is indeed the case this would be why the secondary of the Kacher is not building a higher voltage than the 5kv or so you indicate in your scope shot. THis would indicate that the capacitance at this point should just be enough to provide the adjustment required but not too much. Just my .02

The pulse width IMO should be no less than the time period of the secondaries resonant frequency to get a good output. Less will starve it and too much will mess with its resonance I think.

1.28Mhz = 0.781250 uSec

Tomtech29 · « **Reply #11061 on:** October 25, 2015, 12:07:09 PM »

Hi.
I have long been a wonder see for yourself
16:26
https://www.youtube.com/watch?v=0CUVsS56xqo
The energy must come with a ferrite core coil 28!

at this point he says that it is necessary that the ferrite rod reverses the magnetic field
that acts as a spring!
3:33
https://www.youtube.com/watch?v=iJniq9SjZiY
Attention
and now see note oscilloscope wave direction
1:31
https://www.youtube.com/watch?v=NVUgZAa1CvM

Good which of you I will explain this to me?

I listen to what he says and I saw as well as the 800 Watt light without the use Kacher!
Pll uses or not after it is strange?

Hoppy · « **Reply #11062 on:** October 25, 2015, 12:47:52 PM »

Quote from: Tomtech29 on October 25, 2015, 12:07:09 PM

Attention
and now see note oscilloscope wave direction
1:31
https://www.youtube.com/watch?v=NVUgZAa1CvM

Good which of you I will explain this to me?

I listen to what he says and I saw as well as the 800 Watt light without the use Kacher!
Pll uses or not after it is strange?

This is rather strange as well: -

John.K1 · « **Reply #11063 on:** October 25, 2015, 01:24:38 PM »

In one movie Ruslan says how to wind the coil, in other he says don't do it that way, In one movie he says Akula used the ferite rod to fine tune frequency, in different he says it helps to get some spring effect and in his last movies he says there doesn't need to be that ferrite rod at all.

Tomtech29 · « **Reply #11064 on:** October 25, 2015, 01:36:54 PM »

Quote from: John.K1 on October 25, 2015, 01:24:38 PM

In one movie Ruslan says how to wind the coil, in other he says don't do it that way, In one movie he says Akula used the ferite rod to fine tune frequency, in different he says it helps to get some spring effect and in his last movies he says there doesn't need to be that ferrite rod at all.

16:45
https://www.youtube.com/watch?v=CpuU2mJxR4k
You understand what he's talking about what's going on with that disperse power?

-and that the output of Tesla is to have the impulse and not to the input
I come back to the old system
https://www.youtube.com/watch?v=Qo4DkJnmCSM
8:00
where the output from the coil grenade is charged capacitor
voltage of 980 Volt enter key (pulse at the gate) a current transformer which is It provides about 6 Ampere 36 volt.- (14V.inverter on)
and further inverter and bulb only to the power of 300 watts.

good is can anyone remember how this transformer is to be wound?

John.K1 · « **Reply #11065 on:** October 25, 2015, 02:43:47 PM »

Hi Tomtech- I will take a look at it later one. Going away now. Talk you later

itsu · « **Reply #11066 on:** October 25, 2015, 03:31:38 PM »

Quote from: verpies on October 24, 2015, 11:34:48 PM

You are correct but I don't see how the PLL could not be synched to voltage if it is transferring energy to the LC circuit (Grenade) from AC voltage sources (switched MOSFETs).

So the question is if they (Akula/Ruslan) are aware that in this case a current transformer will peak on the VOLTAGE and NOT on the CURRENT?
They might THINK that they fire the kacher ontop of the current peak, but instead it is firing ontop of the voltage peak and we should too.

Itsu

itsu · « **Reply #11067 on:** October 25, 2015, 03:49:31 PM »

Quote from: starcruiser on October 24, 2015, 11:37:52 PM

I do not think so as the trigger signal is take from the drive signal from the PLL to the Fets for the 15Khz push/pull. SO if the frequency changes the pulse should follow. But you may be correct now that I think about it, but this would always be the issue anyways.

The issue I am concerned with is the fact the more capacitance means it should take a few more cycles to reach trigger point for the logic gates, i.e. t increases. this can be verified by probing the drive signal in the logic gate chain (see capture below) scope the output of the NAND gate against the drive signal, I figure we are seeing a multiple cycles to a signal to the next stage transition signal. like a 4:1 or something like that.

I circled the drive signal sample point after the 3.6k resistor and a blue circle after the second NAND stage.

Starcruiser,

i measured at the points you mentioned, see below screenshot.

Yellow is voltage across the inductor caps
green is the current through the inductor (we are at resonance)
blue is the signal on your red circled point (pin 1 of the 74HC132)
purple is the signal at your blue circled point (pin 6 of the 74HC132)

All referenced to ground.

Itsu

verpies · « **Reply #11068 on:** October 25, 2015, 04:24:26 PM »

Quote from: itsu on October 25, 2015, 03:31:38 PM

So the question is if they (Akula/Ruslan) are aware that in this case a current transformer will peak on the VOLTAGE and NOT on the CURRENT?
They might THINK that they fire the kacher ontop of the current peak, but instead it is firing ontop of the voltage peak and we should too.

Maybe they also hacked the subsequent delay of monostables to fire the "Kacher" where they want to.

AlienGrey · « **Reply #11069 on:** October 25, 2015, 06:59:18 PM »

Quote from: Tomtech29 on October 25, 2015, 01:36:54 PM

16:45
https://www.youtube.com/watch?v=CpuU2mJxR4k
You understand what he's talking about what's going on with that disperse power?

-and that the output of Tesla is to have the impulse and not to the input
I come back to the old system
https://www.youtube.com/watch?v=Qo4DkJnmCSM
8:00
where the output from the coil grenade is charged capacitor
voltage of 980 Volt enter key (pulse at the gate) a current transformer which is It provides about 6 Ampere 36 volt.- (14V.inverter on)
and further inverter and bulb only to the power of 300 watts.

good is can anyone remember how this transformer is to be wound?

I'm glad you have put a device like this one on here, Some time ago some guy called Sargent Gates made an odd device similar in winds to this but a bit different, any how to cut a story short, i also noticed Akula Roman used this idea, the thing is it's a real Bugger to get such a device to work, but when it does it does do some magical things, but as i said Tuning is will drive you in sane until you find out whats going on, have fun. Both wingdings have to be in resonance or you get nothing !!!!!!!!!!!!!!!!!!!!!!

News:

User Menu

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY (Read 11809789 times)

Hoppy

Re: Kapanadze Cousin - DALLY FREE ENERGY

Tomtech29

Re: Kapanadze Cousin - DALLY FREE ENERGY

itsu

Re: Kapanadze Cousin - DALLY FREE ENERGY

verpies

Re: Kapanadze Cousin - DALLY FREE ENERGY

starcruiser

Re: Kapanadze Cousin - DALLY FREE ENERGY

starcruiser

Re: Kapanadze Cousin - DALLY FREE ENERGY

Tomtech29

Re: Kapanadze Cousin - DALLY FREE ENERGY

Hoppy

Re: Kapanadze Cousin - DALLY FREE ENERGY

John.K1

Re: Kapanadze Cousin - DALLY FREE ENERGY

Tomtech29

Re: Kapanadze Cousin - DALLY FREE ENERGY

John.K1

Re: Kapanadze Cousin - DALLY FREE ENERGY

itsu

Re: Kapanadze Cousin - DALLY FREE ENERGY

itsu

Re: Kapanadze Cousin - DALLY FREE ENERGY

verpies

Re: Kapanadze Cousin - DALLY FREE ENERGY

AlienGrey

Re: Kapanadze Cousin - DALLY FREE ENERGY