Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11718530 times)

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #10995 on: October 22, 2015, 04:49:36 PM »
  Itsu and Tomtech:
  Thanks for your videos.
  So, my question now is how does the light output on your set ups compare to normal grid powered bulbs?
  As it's hard to evaluate the output of a bulb when shown on a video, due to the camera adjusting light levels. So, how does your 100w test bulb light when the Kacher is connected, compare to normal 100w bulb on the grid.  20 -50%?

   I am still tuning, and more tuning.   I've now gotten my Kacher's HF, HV streaming to spark a 3-4mm long stream, and the HF stinging is back to be unbearable to the touch.  But, my antenna coil's scope reading is showing only 1.2Mhz, for this to happen, when all circuits are connected and running, and over 3Mhz from the Kacher secondary by itself, when the antenna is disconnected.
   Tomtech: I also have the problem with my Kacher's output and frequency dropping as the Kacher's transistor circuit gets hot. 
I use No heatsink fan on the Kacher heatsink, as I've been trying to avoid using fans.  As, No fans needed or even heatsinks for the fets on the Mazilli now.  I hate to have to hear any fans, in a solid state device.  But, the Kacher's transistor heating may not be the cause of the power drop after a few minutes running. What is the cause of the voltage/amp drop???

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #10996 on: October 22, 2015, 05:10:17 PM »

   I am still tuning, and more tuning.   I've now gotten my Kacher's HF, HV streaming to spark a 3-4mm long stream, and the HF stinging is back to be unbearable to the touch.  But, my antenna coil's scope reading is showing only 1.2Mhz, for this to happen, when all circuits are connected and running, and over 3Mhz from the Kacher secondary by itself, when the antenna is disconnected.
   

Nick,

I may be wrong here but taking T1000's comment to Verpies below, I read this as the Kacher frequency is supposed to be 1/4 or 1/3 of the grenades resonant frequency. So, if your grenade frequency is say 4MHz, then the Kacher should be 1.0MHz or 1.33MHz resp when running with top-load coil and ferrite inductor.

 "In brief: the yoke has series resonance which magnetizes grenade coil. The frequency of LC resonance in yoke matches subharmonics of standing wave resonance. The Tesla coil simulates nanosecond pulse generator and fires up high tension and high voltage RF pulse which is 1/4th - 1/3rth resonant to wavelength passing through grenade coil creating standing waves inside. The PLL takes peak of the current in the yoke and fires up the driver of Tesla coil for very brief period for EMP spike simulation."

T-1000

  • Hero Member
  • *****
  • Posts: 1738
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #10997 on: October 22, 2015, 05:20:21 PM »
I may be wrong here but taking T1000's comment to Verpies below, I read this as the Kacher frequency is supposed to be 1/4 or 1/3 of the grenades resonant frequency. So, if your grenade frequency is say 4MHz, then the Kacher should be 1.0MHz or 1.33MHz resp when running with top-load coil and ferrite inductor.
To be more precise we are talking about longitudinal wave resonance in grenade coil where the wire length defines what frequency is.

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #10998 on: October 22, 2015, 05:20:52 PM »
By the way, here the latest ALLEGGA diagram, it is missing some text and chip symbols and there is as far i can see 1 capacitor (decouple cap) added
to the IR2184 (C14) which has caused all other capacitor ID's to be upped by one.
Also the battery / switch / diode is added at the output

I have changed the input to the switch S1 as both polarities were the same, so the link from pin 4 of the IR2184 is removed and the one from pin 1 is added.
Now the switch really switches between 180° out of phase signals.

At the potmeters R5 and R9 i have added what they do (delaying / widening the pulse going to the Kacher).
The potmeter R14 (PLL) sets the the range that the PLL still locks on the feedback signal, so for my 15Khz resonance signal i have set it to
still lock between 9 and 21 KHz (15KHz in the middle).

The function of the R8 potmeter is not really clear to me, but i understand it will shift the Kacher pulse compared to the Voltage (or current) peak of the inductor
I should be able to shift the kacher to fire from my voltage peak to the current peak (90° off), but that potmeter range is not enough.
Perhaps i should change C5 to 33nF or 330nF as discussed earlier as now it is 330pF in my setup.

Sigh.

Regards Itsu

starcruiser

  • Hero Member
  • *****
  • Posts: 693
    • Starcruiser's Place
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #10999 on: October 22, 2015, 05:38:35 PM »
By the way, here the latest ALLEGGA diagram, it is missing some text and chip symbols and there is as far i can see 1 capacitor (decouple cap) added
to the IR2184 (C14) which has caused all other capacitor ID's to be upped by one.
Also the battery / switch / diode is added at the output

I have changed the input to the switch S1 as both polarities were the same, so the link from pin 4 of the IR2184 is removed and the one from pin 1 is added.
Now the switch really switches between 180° out of phase signals.

At the potmeters R5 and R9 i have added what they do (delaying / widening the pulse going to the Kacher).
The potmeter R14 (PLL) sets the the range that the PLL still locks on the feedback signal, so for my 15Khz resonance signal i have set it to
still lock between 9 and 21 KHz (15KHz in the middle).

The function of the R8 potmeter is not really clear to me, but i understand it will shift the Kacher pulse compared to the Voltage (or current) peak of the inductor
I should be able to shift the kacher to fire from my voltage peak to the current peak (90° off), but that potmeter range is not enough.
Perhaps i should change C5 to 33nF or 330nF as discussed earlier as now it is 330pF in my setup.

Sigh.

Regards Itsu

Itsu,

I would look at adjusting the capacitance value to adjust the timing delay, figure out the delay required (4x operating frequency I think) and us the RC time constant formula to see if the 1C value places it in range at mid point on the potentiometer.

starcruiser

  • Hero Member
  • *****
  • Posts: 693
    • Starcruiser's Place
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11000 on: October 22, 2015, 05:47:33 PM »
For those who are wondering what I am referring to see graphic attached, the reason for the 4x operating frequency is due to the 90° shift (90 x 4 = 360 one cycle), you will want the cap to reach 1C (charge) within the 90° to trigger the kacher, also the voltage achieved will only be about 63% of what is possible, thus the value of the driving voltage needs to be taken into consideration in order to trigger the gates properly.


starcruiser

  • Hero Member
  • *****
  • Posts: 693
    • Starcruiser's Place
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11001 on: October 22, 2015, 06:09:14 PM »
Itsu, the 3300pf (3n3), .0033uf cap with the 1k adj resistor shows to be a 300khz+ frequency now this is at a 1C charge rate, the question is will the gate trigger at 63% of the voltage? or will this take a second cycle? this second cycle will reduce the operating frequency to 150khz or a pulse every 2nd cycle of the grenade circuit.

Can you check the logic gates using your scope before and after each stage to determine how it is triggering prior to making any changes?

John.K1

  • Hero Member
  • *****
  • Posts: 679
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11002 on: October 22, 2015, 08:28:01 PM »
I have a question.

Ruslan's work is based on the Akula's work. Many pages back Nick was posting one of the Akulas movies explaining the principal work of this device.
The funny thing is - Akula consider the inductor (the ferrite bar) between the Tesla secondary and its antenna as a very important element of the device. And why? As he says- it change the sinusoidal wave from the secondary to the wave with sharp front edge .If I good understood  Akula is getting peaks of over 36KV there.  He says this is like a hammer.  Have you got anybody this effect yet?? I am trying to get it myself for two days and still nothing like that. In fact it is hard to believe it can work like that. What is your opinion about it?

Dog-One

  • Hero Member
  • *****
  • Posts: 1019
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11003 on: October 22, 2015, 09:18:01 PM »
I am trying to get it myself for two days and still nothing like that. In fact it is hard to believe it can work like that. What is your opinion about it?

The ferrite rod is wound in a bucking coil arrangement.  If there is anybody that should understand how it may work, it's Chris Sykes.

My feeling is you wind the ferrite rod slightly out of symmetry; if you have it backwards then you should see the tail end of the output wave getting chopped.  None of this will work though if one of the windings isn't exactly in-tune with the frequency of the Tesla coil.  My feeling is you do the following:

First, wind just enough turns in one direction only so this inductor resonates at the same frequency as the Tesla coil.
If you manage to get this working, then you wind a second coil with one less or one more turn in the opposite direction on the same ferrite rod.

I'm not sure of these two coils which one should be tuned to the Tesla coil, the input side or output side, one of them for sure.  Then, another guess is whether the other one should be higher or lower inductance.  Going to take some trial-n-error watching the scope to figure it out.

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11004 on: October 22, 2015, 09:22:04 PM »
  Akula is not showing a 36kv spark, or streamer. As his spark on the ferrite rod (second self runner video) is very weak, unlike Ruslan's streamer.
 It would be more believe able if Akula showed the mentioned voltage on the scope. Especially as neither Ruslan nor Akula use ferrite (like I do) inside of the Kacher former. And are only using relatively short Tesla secondary coils, so it's hard to imagine 36kv.
  But, the voltage is only part of the story, as both amps and frequency also have to be taken in consideration.  The ferrite rod is what creates the "stinging" effect at the antenna, so it does convert the fluffy HV into a stinging and angry sparking HV streamer.   
   Now my Kacher streamer is burning the test wire used to test the streamer. Not to mention what it does to my finger, from the 4 mm burning HV streamer, which smells like BBQ meat, my finger that is.

   What I still don't get, is why Akula or Ruslan don't show the system running at full speed ahead, and then disconnect the Kacher???
                 That's what I want to see...  Would there be any noticeable difference?  From the "boys", and their toys.
 

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11005 on: October 22, 2015, 09:26:44 PM »
How long have you all been working on the device, 5 years ? Show me an oscillograph of the coil under the yellow tap and the large coil on your grenade at the same time, it's obvious whats happening, show it if you will.

John.K1

  • Hero Member
  • *****
  • Posts: 679
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11006 on: October 22, 2015, 09:29:00 PM »
Hi Dog.
"Going to take some trial-n-error watching the scope to figure it out."  -   that's what I  do, and getting tired of it :D
You are right, I might  ask Chris. That delay is because it is saturating the core. This is what I do not understand as you saturate the core with the magnetic flux, but we have just pure potential (HV) there. And than what cause the release of that energy out of the core ?That would be like a spring effect?- and if yes- how to get it? Hmm, more dreamless nights. BTW, in his drawing I just spot the value 15 uH. Have to check my coil.

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11007 on: October 22, 2015, 09:48:12 PM »
    Alien Grey:
   There are no secrets, just many unknowns, but some of us are just busy working on building up, tuning, getting things done.
   I have shown scope shots of the running frequency of my grenade and Kacher several times, if you were following along. But, those are only preliminary readings, and for me those reading are not yet fully established, as that is what I'm up to now. 
Tuning this contraption can take, well,  a while longer anyways.  But, I'll be showing some more scope shots, soon.

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11008 on: October 22, 2015, 09:52:20 PM »
The ferrite rod your taking about  creates spin in the winding's are out of phase by 180 deg, your also changing voltage for current when that's done but the amount depends on other things to do with the other winding's. Done Smith talks about this in one of his seminars.

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11009 on: October 22, 2015, 09:58:18 PM »
    Alien Grey:
   There are no secrets, just many unknowns, but some of us are just busy working on building up, tuning, getting things done.
   I have shown scope shots of the running frequency of my grenade and Kacher several times, if you were following along. But, those are only preliminary readings, and for me those reading are not yet fully established, as that is what I'm up to now. 
Tuning this contraption can take, well,  a while longer anyways.  But, I'll be showing some more scope shots, soon.

Have you got a few links, I'm working on other experiments at the moment and pcbs stuff.