Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11719885 times)

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #10440 on: September 26, 2015, 04:26:35 PM »
Nick,  something is wrong here.

the second picture (0.47uF signal. jpg) is the same picture as in an earlier post of you here:
http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg461330/#msg461330

That one had a different timebase setting (20us/div.) then, so please double check your screenshots.

Regards Itsu

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #10441 on: September 26, 2015, 05:49:16 PM »
Forrest, Hoppy   that's exactly what I mean.  As I said before, I put my Ruslan's replication  on hold and do small experiments with radiant charging , experiments with cap/coils, effect of grounding on the system etc. 

With respect to what Acula says in that movie the most important element is an "inductor" between the Tesla and it's Antenna to get sharp face pulse (He says his pulse shoots over 30KV)  So, can you replicate this? Actually, is it even possible to sharp the front face of the sinus wave by inductor??

I would like to see a good description of the 'effect' being striven for. I saw a marked increase in bulb brightness with my first build when the kacher was energised but this turned out to be caused by HV affecting the PWM switching transistors. I assume that the effect can be observed without the device in loop-back / self-running mode. There are too many gaps in my knowledge to make it worthwhile to re-start building by guesswork and too much unnecessary time wasting as a consequence. I like your approach John, small experiments to gain a better understanding.

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #10442 on: September 26, 2015, 06:28:47 PM »
Nick,  something is wrong here.

the second picture (0.47uF signal. jpg) is the same picture as in an earlier post of you here:
http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg461330/#msg461330

That one had a different timebase setting (20us/div.) then, so please double check your screenshots.

Regards Itsu

   Itsu: That is correct, it's the wrong image which was made previous to installing the new WIMA 1600v, 0.47 turning cap.
  The right image taken yesterday, has replaced it, now, in the edit made to the same post.  Sorry about that.
   

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #10443 on: September 26, 2015, 06:59:59 PM »

Nick,

thats better, so we have for both, 20 cycles in 8 divisions (set at 100us/div.), so doing it the correct / Tinsel way:

20 cycles in (8 x 100 microseconds) = 20/(8 x 0.000100) = 25000 cycles per second = 25 KHz

So your mazilla, inductor and Grenade are running at 25 KHz there.

Regards itsu

magpwr

  • Hero Member
  • *****
  • Posts: 1168
    • Youtube Channel
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #10444 on: September 26, 2015, 07:02:25 PM »
hi everyone,

Taking a look at the 720p Akula video as posted by Nickz.

I have made latest discovery related to where Akula obtained the waveform as was shown in his circuit diagram base on this Tesla coil tuning video video 720p -

www.youtube.com/watch?v=fp3sed_eli0

13.27minute into video 17.xxkhz as shown in attachment.

14:14minute into video obtained as low as 3.1khz (Scope Time div setting at 50us)

With this findings i hope anyone whom is competent enough is able to decode further without theories.
-----------------------------------------------------------------------
Related to FE i have just finished designing 7KV 60ns..80ns 220khz circuit board.28volts -7volts gate drive for 1.2kv Cree SIC mosfet.
I am left with planning a new design for my "isolated" variable HV supply to be placed onto existing PCB.

-------------------------------------------------
I hardly get involved into this forum these days one of the reason being i am no Ruslan supporter.Hence i do get turn off just by the mention of his name every time.

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #10445 on: September 26, 2015, 07:09:27 PM »
 I had dropped the number of turns for the 3 turns coil, which was originally 6 turns, down to about 4 turns. These last images are showing it running with the 4 turns at the yoke.
  Now,  what should I do.... as my Kacher is running at 2.5Mhz, (100:1 ratio) to the 25Khz induction circuit, so all three circuits may be in sync. But, the grenade coil has not been tuned to it "best resonant peak"   Next step?

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #10446 on: September 26, 2015, 07:20:16 PM »

Nick, looking at these latest screenshots, i don't think neither the inductor nor the Grenade coil is in resonance.

I would try to get the inductor in resonance (highest peak, pure sine wave, bulbs on grenade lighting up) by changing the frequency of the mazilla (use your magnet to fine tune, use extra or less capacitance for bigger steps).

Once you have the combo (mazilla, inductor and 3-turn coil) in resonance you can decide the relationship (1:100, 1:60 etc.) for the kacher.

Regards itsu

 

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #10447 on: September 27, 2015, 01:31:35 AM »
    Itsu:
    Ok, I've added a couple more tuning caps along with the bigger 0.47uf wima capacitor, now. Although they are just two lower voltage 400v caps, they do improve the output, and brighten the 3 100w bulbs that I have as the load. I'll also check to see if the primary coil needs more capacitance to be added to it, as well.  Tuning away...

   Edit:  After placing the magnetite magnet into the yoke core, and further adjusting and tuning using the ferrite pieces inside of the grenade, I'm able to kick the circuit into a higher output mode.  It seams to be obtaining some form of resonance, now.
  Here the best tuning I have obtained with the available tuning caps that I have, and the magnet on the yoke, and ferrite in the grenade coil, on the 3 turns coil/0.47uf cap/induction coil circuit. This is with the 100x probe on channel 2, and the settings shown on the second image below.
 
« Last Edit: September 27, 2015, 07:18:27 AM by NickZ »

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #10448 on: September 27, 2015, 11:35:43 AM »

Nick, i think the best is to leave the 0.47uF wima without any other (lower voltage) caps, and ONLY add/remove caps from your mazilla to tune.

The screenshot shows a (not pure sine wave, so not in resonance) 400V pp signal, so it will become more when in resonance.
So only use 2000/1600V capable caps there.



I see 8.4 cycles in 8 divisions (set at 50us/div.), so doing it the correct / Tinsel way:

8.4 cycles in (8 x 50 microseconds) = 8.4/(8 x 0.000050) = 21000 cycles per second = 21 KHz

Happy tuning......Regards Itsu

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #10449 on: September 27, 2015, 12:46:11 PM »
    Itsu:
    Ok, I've added a couple more tuning caps along with the bigger 0.47uf wima capacitor, now. Although they are just two lower voltage 400v caps, they do improve the output, and brighten the 3 100w bulbs that I have as the load. I'll also check to see if the primary coil needs more capacitance to be added to it, as well.  Tuning away...

   Edit:  After placing the magnetite magnet into the yoke core, and further adjusting and tuning using the ferrite pieces inside of the grenade, I'm able to kick the circuit into a higher output mode.  It seams to be obtaining some form of resonance, now.
  Here the best tuning I have obtained with the available tuning caps that I have, and the magnet on the yoke, and ferrite in the grenade coil, on the 3 turns coil/0.47uf cap/induction coil circuit. This is with the 100x probe on channel 2, and the settings shown on the second image below.

Nick,

I think that you need to get hold of a suitable signal generator (up to 5 or 10MHz) before you go any further with tuning. This is needed to establish the natural resonant frequency of your grenade coil as a basis for tuning the inductor at a 50th, 60th or 100th of that frequency, or pick a suitable strong harmonic that can synch with a frequency within the range of your kacher. Having established this, you can then use the SG to tune the inductor combo to the chosen lower KHz frequency. Then the Mazilli can be tuned to run at that frequency eg 25KHz to resonate the inductor. This is my present understanding of the tuning process. Please anybody correct me if I'm wrong.

Dog-One

  • Hero Member
  • *****
  • Posts: 1019
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #10450 on: September 27, 2015, 03:21:04 PM »
I think that you need to get hold of a suitable signal generator (up to 5 or 10MHz) before you go any further with tuning. This is needed to establish the natural resonant frequency of your grenade coil as a basis for tuning the inductor at a 50th, 60th or 100th of that frequency, or pick a suitable strong harmonic that can synch with a frequency within the range of your kacher.

Yes and while you have the capacitors disconnected for this task, it's probably good to have a look at the grenade resonant frequency for both grounded and ungrounded.  There should be a noticeable difference if you think of the grenade coil behaving like a spring.  When one side is held solid, the frequency should be lower than it would with both ends open.  If the two frequencies are nearly the same, I suspect this means your grounding is inadequate.

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #10451 on: September 27, 2015, 04:08:35 PM »
Yes and while you have the capacitors disconnected for this task, it's probably good to have a look at the grenade resonant frequency for both grounded and ungrounded.  There should be a noticeable difference if you think of the grenade coil behaving like a spring.  When one side is held solid, the frequency should be lower than it would with both ends open.  If the two frequencies are nearly the same, I suspect this means your grounding is inadequate.

Yes, a good point, also raised by T1000 that needs to be included in the tuning procedure. I'm unsure about the need for a really thick earth wire of 25mm sq as has been quoted on a couple of schematics. Can someone please explain the technical reason for this. I think it has something to do with heavy pulse currents that are either going to ground or coming from ground, although I cannot understand this given that once the device is running there is no copper return path to the battery power supply. If its purely for running stability purposes for HF capacative grounding, then I think a much small gauge conductor should suffice? However, if there is a source of considerable aetheric 'free' energy requiring a heavy earth grounding, then it suggests that the induction coil is receiving this energy under the influence of the transmitting tesla / Kacher coil antenna. As has been said before, we need to fully understand the modus-operandi of this device and to do that we need to pinpoint the real source and nature of the 'free' energy that enables the device to be looped for self-running as claimed by a few people.

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #10452 on: September 27, 2015, 04:17:47 PM »
Nick, i think the best is to leave the 0.47uF wima without any other (lower voltage) caps, and ONLY add/remove caps from your mazilla to tune.

The screenshot shows a (not pure sine wave, so not in resonance) 400V pp signal, so it will become more when in resonance.
So only use 2000/1600V capable caps there.



I see 8.4 cycles in 8 divisions (set at 50us/div.), so doing it the correct / Tinsel way:

8.4 cycles in (8 x 50 microseconds) = 8.4/(8 x 0.000050) = 21000 cycles per second = 21 KHz

Happy tuning......Regards Itsu

  Itsu:
  I just have a single tuning cap on the Mazilli primary coil, none of my other capacitors will do anything to raise the output there.
  I can correct the shape of the wave form, but it is normally the additional bulbs that are causing it to do that, or tuning caps.
 I can make it look like a perfect sine wave, but the output will go down. And, the best output is obtain when using three 100w bulbs, or more.
  So, if I remove additional caps on the 0.47uf WIMA cap,  the output will go down (not up), as mentioned. And so will the brightness of the bulbs. The end result will be the same wave form, and output as I had shown previously, at the 25Khz readings.

  Hoppy: Yes, I know about the signal generator... But, no one has answered if SCOPE probes will work on a SG, as the one that I can borrow has NO probes. I have one new 1x - 10x probe, that I'm not using at the moment, and also a probe with just two crock clips at the ends. CAN THESE BE USED on the SG???

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #10453 on: September 27, 2015, 04:39:59 PM »
  Itsu:
  I just have a single tuning cap on the Mazilli primary coil, none of my other capacitors will do anything to raise the output there.
  I can correct the shape of the wave form, but it is normally the additional bulbs that are causing it to do that, or tuning caps.
 I can make it look like a perfect sine wave, but the output will go down. And, the best output is obtain when using three 100w bulbs, or more.
  So, if I remove additional caps on the 0.47uf WIMA cap,  the output will go down (not up), as mentioned. And so will the brightness of the bulbs. The end result will be the same wave form, and output as I had shown previously, at the 25Khz readings.

  Hoppy: Yes, I know about the signal generator... But, no one has answered if SCOPE probes will work on a SG, as the one that I can borrow has NO probes. I have one new 1x - 10x probe, that I'm not using at the moment, and also a probe with just two crock clips at the ends. CAN THESE BE USED on the SG???

Nick,

You could use your scope probe set to x1 (straight through or in some cases 1k in line). However you do risk damaging the probe with any heavy current, so my advice would be get hold of a 50 ohm coax lead with BNC termination and croc clips at the other end, which you might already have from the description of your leads.

As you have been advised in the past, ditch your Mazilli for a tuneable PWM, push-pull oscillator.

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #10454 on: September 27, 2015, 04:46:59 PM »
Nick,

you can tune the combo (mazilla, inductor coil, 3-turn coil) to get into resonance by either:

# changing the frequency of the mazilla (to match the present (hidden) resonance frequency of the inductor, 3-turn coil 0.47uF cap)   or by
# changing the frequency of the inductor, 3-turn coil, 0.47uF cap (to match the present (known) resonance frequency of the mazilla).

The first you do by using your magnet on the yoke and/or by adding/removing caps on the mazilla circuit.
The second you do by adding more caps to the 0.47uF caps parallel (more capacitance) or in series (less capacitance) but be aware of the possible high voltage there


Don't care to much for the mazilla output for now, just try to find the resonance frequency of the combo.

See also the good advice from Hoppy.

You can use the probe with the 2 crock clips on the SG, i think its the one Hoppy is talking about (looking at the picture of your scope and cables).

Regards Itsu