Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11718968 times)

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8955 on: June 27, 2015, 10:37:43 PM »
  Well, I'm a bit confused as well. About the Kacher's input, as Ruslan is showing running the Kacher on 24v input from batteries, or power supply. But, the schematic is showing a rectified voltage of 310v, to the kacher circuit. In any case he's getting a nice hefty spark, from what ever the source is.
  When I used non-uf series diodes (IN5408) to make a diode bridge at the output of the bigger grenade coil, they melted their solder points in less than a minute running time. I have not obtained more of the UF series diodes, yet,  to see if they will stand up the overheating issue.
  You'll notice that Ruslan is using 4 of the mosfet looking type of diodes for his bridge, and are also on a heat sink. Those are probably the ones that are overheating when 4000w is being drawn. Probably need more like 4.000 watt rectifier diodes.
  Those red (0.47uf) WIMA caps that Ruslan is using several of, cost $15 each, so, they're not cheap either.

starcruiser

  • Hero Member
  • *****
  • Posts: 693
    • Starcruiser's Place
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8956 on: June 27, 2015, 10:41:41 PM »
I'm guessing the IR2153 circuit boosts voltage to somewhere between 100 and 200 volts, which is triggered across the primary. 

This is the MOSFet driver Ckt using the driver IC is what is used for SSTC designs, my current driver uses this chip as well as its complement for its H bridge. This chip is coupled to the Gates via a small ferrite cored xformer to decouple the HV from the LV side of the circuit. The Fets use a DC supply and a capacitor to drive the primary coil. My initial tests will use this along with a variac to drive the DC side via a FWB and Cap at various voltages.

starcruiser

  • Hero Member
  • *****
  • Posts: 693
    • Starcruiser's Place
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8957 on: June 27, 2015, 10:47:57 PM »
  Well, I'm a bit confused as well. About the Kacher's input, as Ruslan is showing running the Kacher on 24v input from batteries, or power supply. But, the schematic is showing a rectified voltage of 310v, to the kacher circuit. In any case he's getting a nice hefty spark, from what ever the source is.
  When I used non-uf series diodes (IN5408) to make a diode bridge at the output of the bigger grenade coil, they melted their solder points in less than a minute running time. I have not obtained more of the UF series diodes, yet,  to see if they will stand up the overheating issue.
  You'll notice that Ruslan is using 4 of the mosfet looking type of diodes for his bridge, and are also on a heat sink. Those are probably the ones that are overheating when 4000w is being drawn. Probably need more like 4.000 watt rectifier diodes.
  Those red (0.47uf) WIMA caps that Ruslan is using several of, cost $15 each, so, they're not cheap either.

Those are UF diodes most likely and are only rated at 10 to 20 amps, he can increase their current handling if he places a few in parallel to each other, if more voltage handling is required then in series. I was looking at them and they have them from 600V to 1500 volt ratings but they are not cheap.

Bat1Robin2

  • Jr. Member
  • **
  • Posts: 94
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8958 on: June 27, 2015, 11:51:44 PM »
 Dog one,
"Understanding why Ruslan would want to phase lock at the zero crossing"

During experimentation and tuning you will have waveform similar to the one shown below called waveform output example may 7th. The 4046 even with a zero crossing detection circuit will have trouble locking onto that signal. That was my only point in saying the sine wave is not smooth i should have said symmetrical.

A good generator seems better for experimenting. once over unity is accomplished (which will be a long time if ever) then put in your fancy automatic stuff.
The circuit is obviously wish full thinking design due to the s1 wiring being dead wrong. Anyone who builds it like i did will see my point.

The uf diodes have no over heating issues on output with the smaller FETs. (IRF3710)
The Bemf feedback resistor is main overheating issue. ( just use a 7 watt resistor and be done with any overheating issue)
The Bemf is dumped right back onto the 24 volt line. so only the resistor itself is the loss on the bemf harvest. At only 7 watts its not a big factor in the overall efficiency. So no amount of improved bemf capture would help significantly.
Anyone want to buy a slightly used one owner of a over unity device operating at 72% just need a little tweaking and your own your way to no more electric bills.
Only my opinions of my build experience anyone is allowed to there own opinion.

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8959 on: June 28, 2015, 02:17:25 AM »
  Starcruiser:
  The UF4007-- UF4008 are 1000v ultra fast rectifier diodes, but are limited to only 1amp.  The UF series that I'm using, the UF306 diodes, I had thought were higher than that, 3 amps, or so, but I don't think that they are more than an amp. I have to check again.  As I'm probably drawing about 10 to 15 amps, or so, on my set up.  The more I tune for higher output, the hotter the fets get. You can't touch them after only one minute running. Heat-sinks and fans helps, but not enough.  I can't imagine drawing 4000 watts.  T-1000 says that the fets don't draw that much current, if things are working right.
I hope that he's right.

  Here's another image of Ruslan's newest drivers boards (below). As it was taken by my cell phone, from his very blurry video, so, it comes out blurry. When I turned the original image clockwise, it lost even more resolution. Some one can probably get a much clearer shot, but, as the video was blurry, you still won't be able to read the component values.  I don't think, but a much clearer image is doable.
BTW: Oleg, or whatever his name is, has done a nice clean job, fitting all the boards tightly into one junction box.  Great work! 
I can further imagine all three boards, all built onto a single mother board.    Nice!   How much?    Hey, just kidding...   


 
 
 

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8960 on: June 28, 2015, 08:24:23 AM »
I managed to find this Pic.

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8961 on: June 28, 2015, 11:31:04 AM »

Anyone want to buy a slightly used one owner of a over unity device operating at 72% just need a little tweaking and your own your way to no more electric bills.
Only my opinions of my build experience anyone is allowed to there own opinion.

Maybe you could sell your push-pull to Nick, as IMO he needs to ditch his Mazilli.

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8962 on: June 28, 2015, 02:01:12 PM »
Ive just been going over some of the scope shots presumably some of our Russian friends have been posting, one shot shows a 'mustache ' shape photo Enjoykin explains is how the wave form should be but i can't understand how that waveform can be generated from the circuits at this moment, as the sine wave peek goes positive at the top a huge positive EHT spike is generated and on a negative sine wave peak is generated on the reverse polarity a negative EHT spike is generated, are you with what I’m showing and saying ?

Have a good look at this photo your self, and think about what’s suppose to be happening. My next question is has any one achived this waveform yet ?

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8963 on: June 28, 2015, 02:20:46 PM »
Ive just been going over some of the scope shots presumably some of our Russian friends have been posting, one shot shows a 'mustache ' shape photo Enjoykin explains is how the wave form should be but i can't understand how that waveform can be generated from the circuits at this moment, as the sine wave peek goes positive at the top a huge positive EHT spike is generated and on a negative sine wave peak is generated on the reverse polarity a negative EHT spike is generated, are you with what I’m showing and saying ?

Have a good look at this photo your self, and think about what’s suppose to be happening. My next question is has any one achived this waveform yet ?

Yes, me and I think Magpwr achieved a very similar waveform. Mine is below. I can't remember what post number this was discussed under but it was some way back in this thread.

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8964 on: June 28, 2015, 02:59:39 PM »
  Aliengrey:
  Nice image of Ruslan's newest device drivers, but like I had mentioned,  I don't think that it's clear enough to read the component values.
  I wonder if the three red colored capacitors on the Kacher board are there to filter out the 300v input in to the Kacher circuit. Or not?
 
 

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8965 on: June 28, 2015, 05:30:29 PM »
For those experimenting on simpler lines, the circuit arrangement from radiant_one below, may be worthwhile to try out. Basically, replace the oscillator with a push-pull and L2 with the grenade coil.

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8966 on: June 28, 2015, 06:32:33 PM »
  Hoppy, from what I can see of the diagram that you just posted. That is a Dr. Stiffler Exciter circuit. Or a version of it, and only works with leds. "Energy from the air" (Docs title).  Not from the ground. The ground just aids in the process.
  My kacher won't light a bulb without an earth ground connection to the Kacher transistor negative rail.  That doesn't mean that I'm getting anything FROM the ground though.

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8967 on: June 28, 2015, 06:50:43 PM »
  Hoppy, from what I can see of the diagram that you just posted. That is a Dr. Stiffler Exciter circuit. Or a version of it, and only works with leds. "Energy from the air" (Docs title).  Not from the ground. The ground just aids in the process.
  My kacher won't light a bulb without an earth ground connection to the Kacher transistor negative rail.  That doesn't mean that I'm getting anything FROM the ground though.

Nick,

Yes indeed, the circuit shown only works with LED's. I wrote suggesting replacing this oscillator with a suitably designed high powered version and replacing L2 air cored inductor with the grenade coil - inductor. The grenade coil would then pass the coil discharge to ground via the Ruslan / Akula style lamp array. I think this maybe basically what Kapanadze is doing.

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8968 on: June 28, 2015, 07:33:13 PM »
  If a Mazilli is connected to the yoke coils, then from the 3 turns yoke coil to the grenade inductor, (which is what I have already). And if the 168 turns output coil on the grenade is connected only to a small bulb, that is going to earth ground. Then that should be some what like what you suggested doing, with your mods to the above diagram. Or not?

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8969 on: June 28, 2015, 08:35:22 PM »
  If a Mazilli is connected to the yoke coils, then from the 3 turns yoke coil to the grenade inductor, (which is what I have already). And if the 168 turns output coil on the grenade is connected only to a small bulb, that is going to earth ground. Then that should be some what like what you suggested doing, with your mods to the above diagram. Or not?

Nick,

I don't see it as a transformer interface. A PWM push-pull with just the top half of the drive coil connected is how I envisage the oscillator. It's likely that in the Kapanadze type device, the oscillator coil discharge charges a cap bank and a capacitive discharge circuit controlled by a spark gap is needed to discharge high frequency and high voltage pulses into the grenade coil. The operating frequency, ground cable length and earth resistance may then prove critical for optimum performance (impedance matching). Its likely that Kapanadze used his inverter to provide an isolated AC supply that was then transformed and rectified down to a suitable lower DC voltage to drive the power oscillator. The heatsink and fan arrangement on Kapanadze's oscillators suggest that considerable heat is dissipated.

I believe the 'effect' is something to do with how the lamps respond to a particular and optimally adjusted pulsed waveform and nothing to do with NMR or any other fancy effect.