Did you measured little moustashes (current) with current transformer or maybe with resistor ?

Did you wound your bifilar like Tesla setup or Hooper setup. There is big difference between !!
Lenght of bifilar 18,75m (half of grenade).

This is important - Your second oscillogram at 22.18.43 is very important and very similar to Ruslan.
Watch his video again from 1.04 and compare yourself. He has on top of positive and negative peaks small humps. It means you have significant phase error in your setup.

I need some time to redraw Brutto schematic as i think it should be !! 

Picture for compose one's thoughts.

hi Enjoykin,

I may like Brutto drawing of the circuit diagram as you have shown us.

But Brutto have not produced any working device yet.

People are still using 1/4 and 1/8 resonance for this device.I think they are mixing up this with Don Smith device which is base on 1/4 wave.

Why isn't there anyone else besides me whom realized for Akula video it's all about the Harmonics or Sub-harmonics.30th Harmonics and 60th Harmonics for new device.

In order to see perfect frequency alignment only 30th harmonics and 60th harmonics is suitable .2 reasons one is to fit within yoke core capability to around 75khz and another fit within air-core capability not below 18khz as mentioned by Akula.

In the old Akula video tela coil tuning video .The frequency derive from his sprecturm analyser is 165khz and another signal is 55khz .

Use the attached Harmonics calculator it reveal "1650900hz" as 30th harmonics for 55030hz.This is to see prefect frequency alignment besides 60th harmonics.

This is the last time i will be talking about harmonics.

My variant of Ruslan device. 

to Itsu
Now i will watch your video. Thank you and good luck !!

Reg.

Can anybody give me some info about that small coil right behind the Tesla coil?. It is some turns OPPOSITE to Tesla . It is under the red tape.    (7:13 ,   https://www.youtube.com/watch?v=KN-ZmCW0W8w  ) ??
Cheers

Hi John. I don't think Ruslan has commented on why he did this yet, or at least I haven't
seen any translations where Ruslan explains why he did this. 
Ruslan may only have done this because he was replicating closely what Akula did.
It may be to try to isolate the tesla coil secondary somewhat from loading by the
big antenna coil. Not sure though.  May be for some other purpose entirely.
All the best...

hi Enjoykin,

I may like Brutto drawing of the circuit diagram as you have shown us.

But Brutto have not produced any working device yet.

People are still using 1/4 and 1/8 resonance for this device.I think they are mixing up this with Don Smith device which is base on 1/4 wave.

Why isn't there anyone else besides me whom realized for Akula video it's all about the Harmonics or Sub-harmonics.30th Harmonics and 60th Harmonics for new device.

In order to see perfect frequency alignment only 30th harmonics and 60th harmonics is suitable .2 reasons one is to fit within yoke core capability to around 75khz and another fit within air-core capability not below 18khz as mentioned by Akula.

In the old Akula video tela coil tuning video .The frequency derive from his sprecturm analyser is 165khz and another signal is 55khz .

Use the attached Harmonics calculator it reveal "1650900hz" as 30th harmonics for 55030hz.This is to see prefect frequency alignment besides 60th harmonics.

This is the last time i will be talking about harmonics.

Hello magpwr !! 

Why last time ?? I think you are right - everything here is about Complex-Harmonic-Mixing. Akula probably used 30th harmonic with his Tesla transformers - Ruslan used 50th Harmonic as he said in his new video. You can tray mixing of Telluric frequency with highest amplitude response (somwhere from 4-7 MHz) but is extremely difficult to get results as Akula said  - because he has tried it.

When i said  Harmonics or Sub-harmonics i mean not only to fit two main Harmonics but maybe all Harmonics and their all Sub-harmonics. To be sure what;s going on here we need something like Harmonic Spectrum anaylyser - to scan complete phase space from 0Hz up to 1GHz and more.
But Complex-Harmonic-Mixing is not only main stuff. Here is also Present Tesla Radiant which is totaly unknown for us - what he is doing, how and why he is doing like he do !! Tesla Radiant is pretty Big Shark for us - Megalodon Shark !!

Ruslan new video
https://www.youtube.com/watch?v=C8RcRlzk16w

Both of them used 1/2 wave lenght for consistent phase mxing. Maybe is there something more what we don't know or have not taken in account.

Reg.

Meno,  It is not in your schematic. But if you watch one of his videos, he has on the tube - Tesla , after there are some turns in opposite direction (he clearly state that, also small gap between tesla and this coil) and then, this is connected to the coils on ferrite bar.  I didn't find more info about this anywhere.   His opposite coil is under the red tape.

Thanks.

That part need to hold ferite road.

Hello magpwr !! 

Why last time ?? I think you are right - everything here is about Complex-Harmonic-Mixing. Akula probably used 30th harmonic with his Tesla transformers - Ruslan used 50th Harmonic as he said in his new video. You can tray mixing of Telluric frequency with highest amplitude response (somwhere from 4-7 MHz) but is extremely difficult to get results as Akula said  - because he has tried it.

When i said  Harmonics or Sub-harmonics i mean not only to fit two main Harmonics but maybe all Harmonics and their all Sub-harmonics. To be sure what;s going on here we need something like Harmonic Spectrum anaylyser - to scan complete phase space from 0Hz up to 1GHz and more.
But Complex-Harmonic-Mixing is not only main stuff. Here is also Present Tesla Radiant which is totaly unknown for us - what he is doing, how and why he is doing like he do !! Tesla Radiant is pretty Big Shark for us - Megalodon Shark !!

Ruslan new video
https://www.youtube.com/watch?v=C8RcRlzk16w

Both of them used 1/2 wave lenght for consistent phase mxing. Maybe is there something more what we don't know or have not taken in account.

Reg.

hi Enjoykin,

It's not your fault.I have mentioned about Harmonics before you came to this forum.But other members are getting mixed up with Don smith by using 1/4 or 1/8 wave in the Russian forum.
They are being lead into the wrong direction by following brutto.

I like this coil presentation which you have attached previously.
This way no more stupid question from others related to how to wind a coil if they don't wish to dig for information.

Recall my findings on frequency used to connect to 1.0xuf capacitor in series with 25 turns windings.For my case it was found to be at 14.85khz upper frequency 871khz.
Then these needs to be multiplied by 2.   example : 14.85khz x 2 =29.7khz (Yoke core frequency at 3 turns) and 871khz x 2 = 1.742Mhz (Tesla coil)

This is the only area where 1/2 wave is applicable.

------------------------------------------------
I just received the Russian PIO capacitors 20uf 400volts which was sold as pairs and the KT926 transistor.

-----------------------------------------------

For Tesla coil at the top(Nearest to the middle of pvc pipe) just few turns around 5 with spacing with between those windings using the same continuous magnet core will do as well.

The reason for this few turn is to optimize streamers/spark from the top and ensure less wastage from the sides of coil.

The next 2 screenshots taken from this last Ruslan video clearly shows that the big moustache
signal was taken directly from across the main Grenade coil terminating via a FWBR into 2 capacitor.

Questions:
where is this FWBR with its caps shown in any diagram?
what is the purpose of this FWBR and caps?

Together with the current transformer measuring the current in the main Grenade (does it?), it makes sense
to monitor both voltage across and current through this main Grenade to get them aligned, meaning get this coil in resonance.

Regards itsu

hi itsu,

I thought no one will ask about it.

Since you mentioned about it .The reason why i merely used only 3 turns for the output for my previous setup without the 28 turns from the yoke\toroid which was previously used merely to be full -bridge rectified and was charging the pulse capacitor.

The new design is tapping from the output(Full bridge rectifier as you attached for the grey capacitor) which is leading back as A/C to the bulb & Power supply unit  for loop back purpose.

A/C voltage meant for bulb/PSU if rectified would produce higher dc voltage for pulsing application as compared to 28 turns which the diameter of the yoke was the constraint.


-------------------------

I have attached 2 photos of interest.

This toroid is where i previously spotted one of the 3 turns wire  from yoke core is going through.
Previously i though it was used for AFC then base on this video i noticed there is no interface wire spotted which is suppose to go back to PWM circuit with boost circuit and TC4420 driver.

This is the likely point to inject nanosecond pulse (low voltage first) which is the next stage of my experiment later.

Can be seen clearly for this video the probe is connected to toroid as attached.

I have editted my previous post concerning the current transformer position.

Magpwr, i understand the toroid is a simple current transformer to measure the current through this white wire.

Hoppy,  i agree, enjoykin has reversed all directions in his pictures/diagrams compared to what it really is,
but i don't think it really matters

Regards itsu