Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11718071 times)

Enjoykin

  • Sr. Member
  • ****
  • Posts: 269
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5865 on: October 19, 2014, 06:42:57 AM »
Hi Jeg

In Katcher between base and 1K potentiometer should be closed connection. To protect transistor put small resistor about 100- 400 ohms in series with 3K potentiometer or don't twist potentiometer to lower value below 100 ohms.

You should tune your Katcher with oscilloscope to get 5kV-6kV output amplitude with nice sharp unipolar impulses (mono-polar impulses).

Do the same as Ruslan did in video.

Cool it like this:

Качер на КТ805  Anapa More
http://www.youtube.com/watch?v=4XWFtHG-90A

Reg.
________________________________
Hi Itsu

You should have 5kVpp-7kVpp amplitude at your Pulsar and lot of reactive power in circuit to trigger OU effect. Why ? Because OU effect has own absolute threshold on those levels. Also phasing coils is very important. Try winding coaxial from left to right and right to left. Also try coaxial with open and shorted ends and try "kick" HV impulse not on central conductor but on outer while central coductor put on ground potential or leave free in air.  Sweep your pulser from null to maximum and look on light bulbs and oscilloscope. Principle is working and was checked many people.

Reg.
« Last Edit: October 19, 2014, 09:16:50 AM by Enjoykin »

Enjoykin

  • Sr. Member
  • ****
  • Posts: 269
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5866 on: October 19, 2014, 07:35:43 AM »
Граната Руслана на 5кВт  -  Ruslan's granade at 5KWt


Make Ruslan coil on this way:

1. Obtain: oscilloscope 10....50MHz, 60m copper wire 2.5 mm2 PVC isolation, 4 m copper wire 4....6 mm2, 20 m copper wire 16....20 mm2, PVC water pipe 50 mm dimater 1 m long, 2m (or more better) cooper rod 20...40 mm diameter.
2. Cut 2.5 mm2 wire exactly at 37.5 m. Remain wire cut on 18.75m for bifilar inductor. Cut 16....20 mm2 wire exactly at 18.75m and weld one end to copper rod sticked into ground. Bifilar and ground wire should be exacly 18.75m.
3. Make your Grenade like Ruslan has shown at picture.
4. 1st and 2nd layer wind from left to right (your position is reference).
5. on half on 2nd layer wind 3rd layer from right to left. 4th layer same as 3rd.
6. on half of 4th start winding 5th from right to left. Also do for 6th layer.
7. remain wire put through the plastic tube. It will be one end.
8. wind bifilar inductor over 2nd layer, opposite to 1st and 2nd. In our case from right to left.
9. Make a Katcher coils on free half of PVC pipe. Primary shoud have 3..5 turns 4....6 mm2 wire with distance of 3 fingers between primary and secondary. Secondary should resonate about 3MHz...4MHZ without antenna and small bifilar choke between. Tune Katecher to get nice sharp unipolar impulses as Ruslan has shown in video. Secondary wire from 0,35mm....0.75mm - a lot of turns. Correct number depend from wire diameter.
10. Make antenna around inductor about 5..6 turns of 4....6 mm2 wire. Distance from antena to inductor should be minimum 3 fingers (Ruslan's measurement) on both side.
11. Make small bifilar choke on ferrite rod 10...12 cm lenght, 10mm diameter. wind one half 5..6 turns from left to right , other from right to left.  Connect grounding and tune Katcher secondary lenght (from base of transistor), antenna (find best tap on 5 turns coil) and use small bifilar choke for fine tuning. You should get as on picture above, exactly at 2 MHz with maximum amplitude you may get. All tuning should be done with grounding.

Than sit and drink beer.  :) First part was finished.

For more details download and look all Ruslan Kulabuhov vids.
http://www.youtube.com/channel/UC_zn0cdzv_qfsxQUm4e7R9w/videos

Reg.

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5867 on: October 19, 2014, 11:39:58 AM »

Thanks Enjoykin, 

looks simple enough   ::)




Guys,  take care NOT to use a lab PS when tuning/testing your Kacher, use a battery or a simple 12/24V PS.
Last night one half of my double PS went out with a big bang while tuning my new kacher  >:(

There is loads of RF going into your PS with the above result, the same warning i did read on the Russian forum last week or so.

Regards itsu

Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5868 on: October 19, 2014, 01:06:31 PM »
Граната Руслана на 5кВт  -  Ruslan's granade at 5KWt


Make Ruslan coil on this way:

1. Obtain: oscilloscope 10....50MHz, 60m copper wire 2.5 mm2 PVC isolation, 4 m copper wire 4....6 mm2, 20 m copper wire 16....20 mm2, PVC water pipe 50 mm dimater 1 m long, 2m (or more better) cooper rod 20...40 mm diameter.
2. Cut 2.5 mm2 wire exactly at 37.5 m. Remain wire cut on 18.75m for bifilar inductor. Cut 16....20 mm2 wire exactly at 18.75m and weld one end to copper rod sticked into ground. Bifilar and ground wire should be exacly 18.75m.
3. Make your Grenade like Ruslan has shown at picture.
4. 1st and 2nd layer wind from left to right (your position is reference).
5. on half on 2nd layer wind 3rd layer from right to left. 4th layer same as 3rd.
6. on half of 4th start winding 5th from right to left. Also do for 6th layer.
7. remain wire put through the plastic tube. It will be one end.
8. wind bifilar inductor over 2nd layer, opposite to 1st and 2nd. In our case from right to left.
9. Make a Katcher coils on free half of PVC pipe. Primary shoud have 3..5 turns 4....6 mm2 wire with distance of 3 fingers between primary and secondary. Secondary should resonate about 3MHz...4MHZ without antenna and small bifilar choke between. Tune Katecher to get nice sharp unipolar impulses as Ruslan has shown in video. Secondary wire from 0,35mm....0.75mm - a lot of turns. Correct number depend from wire diameter.
10. Make antenna around inductor about 5..6 turns of 4....6 mm2 wire. Distance from antena to inductor should be minimum 3 fingers (Ruslan's measurement) on both side.
11. Make small bifilar choke on ferrite rod 10...12 cm lenght, 10mm diameter. wind one half 5..6 turns from left to right , other from right to left.  Connect grounding and tune Katcher secondary lenght (from base of transistor), antenna (find best tap on 5 turns coil) and use small bifilar choke for fine tuning. You should get as on picture above, exactly at 2 MHz with maximum amplitude you may get. All tuning should be done with grounding.

Than sit and drink beer.  :) First part was finished.

For more details download and look all Ruslan Kulabuhov vids.
http://www.youtube.com/channel/UC_zn0cdzv_qfsxQUm4e7R9w/videos

Reg.
Enjokin, your gift is welcomed and well appreciated! :) If you don't mind, I have some few questions so to be more compatible with.

1. In which direction you wind your Tesla coil compares to the first two grenade layers as a reference
2. In which direction you wind katcher's antenna compares to the first two grenade layers
3. Is a coupling capacitor needed between grenade and yoke windings? Because without coupling there, we have to count/add the length of the 28T yoke secondary to the length of the grenade as they are in series..

Thanks again
Jeg


Ps. Yesterday night I saw Menoffather in my dreams talking with Itsu about the decoupling capacitor. Is it something to worry about??? :D

Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5869 on: October 19, 2014, 01:15:40 PM »
Thanks Enjoykin, 

looks simple enough   ::)




Guys,  take care NOT to use a lab PS when tuning/testing your Kacher, use a battery or a simple 12/24V PS.
Last night one half of my double PS went out with a big bang while tuning my new kacher  >:(

There is loads of RF going into your PS with the above result, the same warning i did read on the Russian forum last week or so.

Regards itsu

Itsu i already burned my 75Euro scope's probe with katcher, when an arc occurred between katcher's antenna and grenade! You should know that it is not the proper way for tuning katcher by feeding it through batteries. The frequency is absolute depend on katcher's voltage supply. I learned it the hard way. I was tuning my katcher a whole evening. And when I changed batteries to some fresh ones, the res. Frequency changed again... a lot!! 

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5870 on: October 19, 2014, 01:32:14 PM »
Enjokin, your gift is welcomed and well appreciated! :) If you don't mind, I have some few questions so to be more compatible with.

1. In which direction you wind your Tesla coil compares to the first two grenade layers as a reference
2. In which direction you wind katcher's antenna compares to the first two grenade layers
3. Is a coupling capacitor needed between grenade and yoke windings? Because without coupling there, we have to count/add the length of the 28T yoke secondary to the length of the grenade as they are in series..

Thanks again
Jeg


Ps. Yesterday night I saw Menoffather in my dreams talking with Itsu about the decoupling capacitor. Is it something to worry about??? :D


Also could Enjoykin please explain why 16mm sq earth cable is needed when I see Ruslan using thin wire?

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5871 on: October 19, 2014, 01:44:42 PM »
Itsu i already burned my 75Euro scope's probe with katcher, when an arc occurred between katcher's antenna and grenade! You should know that it is not the proper way for tuning katcher by feeding it through batteries. The frequency is absolute depend on katcher's voltage supply. I learned it the hard way. I was tuning my katcher a whole evening. And when I changed batteries to some fresh ones, the res. Frequency changed again... a lot!!


What are the two diodes being used for on Ruslan's Kacher circuit board?

Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5872 on: October 19, 2014, 01:52:48 PM »

What are the two diodes being used for on Ruslan's Kacher circuit board?

I didn't notice them! You mean that he keeps his supply input voltage steady with some zeners?

Just saw again ruslan's video and you are right.
Do you know about the type of his katcher's input choke in common mode? Any proposal for the number of turns and the awg of the magnet wire used?
Thanks Hoppy

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5873 on: October 19, 2014, 02:19:25 PM »
I didn't notice them! You mean that he keeps his supply input voltage steady with some zeners?

Can you please direct me to the right picture or video?

Thanks Hoppy


I can't tell whether they are zeners or how they are placed into circuit.


Clip is from Ruslan video: -


http://www.youtube.com/watch?v=KlXM2nYtbus&list=UU_zn0cdzv_qfsxQUm4e7R9w&spfreload=10%20Message%3A%20JSON%20Parse%20error%3A%20Unexpected%20EOF%20(url%3A%20http%3A%2F%2Fwww.youtube.com%2Fwatch%3Fv%3DKlXM2nYtbus%26list%3DUU_zn0cdzv_qfsxQUm4e7R9w)

Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5874 on: October 19, 2014, 02:22:39 PM »

I can't tell whether they are zeners or how they are placed into circuit.


Clip is from Ruslan video: -


http://www.youtube.com/watch?v=KlXM2nYtbus&list=UU_zn0cdzv_qfsxQUm4e7R9w&spfreload=10%20Message%3A%20JSON%20Parse%20error%3A%20Unexpected%20EOF%20(url%3A%20http%3A%2F%2Fwww.youtube.com%2Fwatch%3Fv%3DKlXM2nYtbus%26list%3DUU_zn0cdzv_qfsxQUm4e7R9w)

Thanks man. I just modified my previous answer. Just saw the video again. Any ideas about his input choke?

There many chances for being zeners because as I told before, frequency and voltage level are closely dependent values between each other.

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5875 on: October 19, 2014, 02:27:13 PM »
Thanks man. I just modified my previous answer. Just saw the video again. Any ideas about his input choke?


I have an identical one and as wired its inductance is in milli-henries, not micro-henries. If you look carefully, you will see that he has re-wound it with what looks like thin PVC covered wire. I did this and got the inductance down to around 300uH. I doubt whether his is as low as 100uH as shown on the circuit. My choke came from a stripped down SMPS and it is a common mode type.

magpwr

  • Hero Member
  • *****
  • Posts: 1168
    • Youtube Channel
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5876 on: October 19, 2014, 02:42:28 PM »
hi everyone,

I have just created a simple prototype high frequency divide by 60 circuit in the virtual at this moment using just 2  I/C 74HC4017.One doing div by 6 and another div by 10.Total div by 60.
Maximum tested frequency at 10Mhz although i don't need that high.

Recall the waveform which i was talking about which is aligned.I found that by playing with signal generator at the lowest test frequency 18khz .The upper frequency needed is 1.075Mhz...1.08Mhz.
By referring to the Harmonics calculator it is always divide by 60 to get the alignment.

Currently i only got just 1 4017 I/C which is only able to handle up to 2.4Mhz base on signal generator.


The 4017 clock input is protected by 1N4148 to positive and negative supply.I just use a short wire as antenna and tested with my existing old tesla coil resonating at around 556khz.
The 4017 is able to properly div by 10 and produce nice waveform at 55.6khz.

This div by 60 is not completed yet since i just completed the basic design few hours ago.

The primary objective in creating this circuit is to ensure the tesla coil resonating frequency will always be divided by 60 via
 small wire antenna and this output of div by 60 will be fed to the yoke driver at the later stage. :D :D :D


If i have it my way then i am no longer worried about tuning the pwm generator to match tesla coil harmonics.Since i just use tesla coil frequency to sync the
yoke driver at 60th sub-harmonics at the later stage.Or worst no need to worry about tesla coil run away resonating frequency.

This is my future planning since i don't have yoke/large toroid core yet.

My utimate plan is to fit all the circuit including the yoke/toroid core into one large pcb board.There will be various section in the circuit board.
The only component to be placed external would be the high energy discharge capacitor.

"Slowly all the puzzle will be fitted together at a quantum level to form this unit" ;D

 

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5877 on: October 19, 2014, 03:24:07 PM »
Thanks man. I just modified my previous answer. Just saw the video again. Any ideas about his input choke?

There many chances for being zeners because as I told before, frequency and voltage level are closely dependent values between each other.


Jeg,


Yes, most likely a couple of  zeners / transorbs in series (cathode to cathode) across the collect / emitter.

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5878 on: October 19, 2014, 03:31:07 PM »
Thanks Enjoykin, 


Guys,  take care NOT to use a lab PS when tuning/testing your Kacher, use a battery or a simple 12/24V PS.
Last night one half of my double PS went out with a big bang while tuning my new kacher  >:(

There is loads of RF going into your PS with the above result, the same warning i did read on the Russian forum last week or so.

Regards itsu


Good advice Itsu! I've repaired my dual channel PSU four times in the past playing with Bedini circuits!!

Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5879 on: October 19, 2014, 03:34:58 PM »

Jeg,


Yes, most likely a couple of  zeners / transorbs in series (cathode to cathode) across the collect / emitter.

Thanks Hoppy, i appreciate it.
I saw somewhere in my scrap storage a similar choke. I am going to search for it.  ;)