Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11715867 times)

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5460 on: October 01, 2014, 07:41:39 PM »
Hi Itsu. I am not sure if you mentioned it already or not, but did you measure the
inductance of your multi-layer bifilar coil? if so, what is the measured inductance?
Did you wind the 2x24 and 2x12 turns layers in the opposite direction to the 2x48 layer?
By any chance did you measure the full length of the wire you used to wind this coil, or
did you just wind it and not measure the full length of the wire?
I am going to wind my bifilar soon, so just wondering how you have done yours.
By the way, your coil assembly is a work or art. Very nice assembly job! :)
All the best.

Thanks void,

use plenty of electrical tape to restrict movement.

I just measured it, here the data from my Agilent U7133C LCR meter:

121.8uH @ 100Hz,    ESR=0.26 Ohm
145.8uH @ 1KHz,     ESR=0.27 Ohm
139.1uH @ 10KHz,   ESR=0.87 Ohm
121.8uH @ 100KHz, ESR=4.2 Ohm

First layers (2x 48 turns) is CCW, other layers (2x 24 and 2x 12) are CW.

I did not measure the lenght upfront  :-(

I again measured the resonance frequency as it is right now (with all the other coils around it) and the first strong resonance peak is at 4008KHz.

Regards Itsu   

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5461 on: October 01, 2014, 07:45:06 PM »
   Geo has suggested using one wire to wind the bigger air coil. Winding in one direction back and forth. But, That method is not a bifilar wound coil. OR is it?
    I've followed the way that TK's blue coil is wound, including being opposite wound for the cancelling effect.  Hopefully this will reduce the draw from the device's own feed back source.
  There are various ways to go on this. Which way works best, is to be seen.
Or, any way,  that finally WORKS...

Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5462 on: October 01, 2014, 08:00:42 PM »

I did not measure the lenght upfront  :-(


Regards Itsu

Give me the exact diameter of your pipe and the outer diameter of your wire including insulation

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5463 on: October 01, 2014, 08:06:33 PM »
   Geo has suggested using one wire to wind the bigger air coil. Winding in one direction back and forth. But, That method is not a bifilar wound coil. OR is it?
   

No, not IMO as the two conductors forming the bifilar should be wound in the same layer. The two wires can then be connected in different configurations. The TK coil shown is a continuous wind of a single conductor intended to form a Tesla type capacitor IMO. However, I'm not sure how its layers are phased. Perhaps Geo can give us exact winding details?

Void

  • Hero Member
  • *****
  • Posts: 2333
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5464 on: October 01, 2014, 08:13:22 PM »
Thanks void,
use plenty of electrical tape to restrict movement.
I just measured it, here the data from my Agilent U7133C LCR meter:
121.8uH @ 100Hz,    ESR=0.26 Ohm
145.8uH @ 1KHz,     ESR=0.27 Ohm
139.1uH @ 10KHz,   ESR=0.87 Ohm
121.8uH @ 100KHz, ESR=4.2 Ohm
First layers (2x 48 turns) is CCW, other layers (2x 24 and 2x 12) are CW.
I did not measure the lenght upfront  :-(
I again measured the resonance frequency as it is right now (with all the other coils around it) and the first strong resonance peak is at 4008KHz.
Regards Itsu

Hi Itsu. Thanks very much for the info.
All the best...

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5465 on: October 01, 2014, 08:42:49 PM »
Give me the exact diameter of your pipe and the outer diameter of your wire including insulation

Hi Jeg,


pipe is 5cm diameter, wire including insulation is 3.3mm.

Be aware that its very hard if not impossible to wire the next layer exactly on top of the lower layer, so normally what has happened is
that the next layer wire lies inbetween the lower layer wires  :o   
I measured the 6 layers at the left side of my coil to be 17.5mm thick, so 2.9mm each layer.


Regards Itsu

a.king21

  • Hero Member
  • *****
  • Posts: 1650
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5466 on: October 01, 2014, 10:46:27 PM »
Hoppy, and all:  Kapanadze told me that the earth wire can be replaced by a circuit.
When I pressed him further he said it could be replaced by the negative terminal of a car battery.
This is pure Tesla tech. I have read that Tesla used the same technique.
Tesla has stated that in some of his devices you could replace an earth ground with the negative
terminal of a lead acid accumulator (car battery).
I pressed both Mike and his interpreter (who were both present during the aquarium 2 demo)
and both confirmed that the earth wire was disconnected for a few minutes.
I talked to both of them independently and some days apart.
My conclusion is that the earth "ground" is required to keep the device in phase.
I have seen experiments on youtube where the disconnect of an earth wire caused experiments to lose power,
although I don't have these video urls now.
Kapanadze uses high frequency mixing in his device. This is proved by the "dancing meters" witnessed by independent testers of some of his devices.
The only other patent I have found which uses the same technique is by Carlos Benitez.
In one of  his patents he says that an "oscillatory circuit" is required to be mixed with DC to produce OU.
An oscillatory circuit is 19th century speak for "tank circuit".
Akula use the same principle.


itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5467 on: October 01, 2014, 11:12:13 PM »

A little progress video below.

I finished breadboarding the TL494 with ucc37322 MOSFET drivers and IRFP260N MOSFET's.
Nice 27KHz square wave signals on the gates (drains not connected yet).

I also used one of the ucc37322 signals as input for my nano pulser with result that i now have a synced (27KHz) nano pulse (240V pp / 30ns wide).
This nano pulser now used only 40V dc as input on its MOSFET, and can take 200V input or more for a 1500V pp pulse if needed.

I also show the signal on the multi layer coil with kacher activated.
It shows that the kacher is very instable as the HV probe makes it change from 1MHz without it to 723KHz with HV probe attached.

Finally i made a remark in the video about the used primary of the yoke as seen in the latest Ruslan video.
This primary has about 2x 12 turns, so NOT the 2x 6 turns in the diagrams, see screenshot below (yellow wiring):
I started with the yoke as mentioned in the diagram, meaning 2x 6 turns primary and 28 turns / 3 turn secondaries (all CW).


Video here:  https://www.youtube.com/watch?v=hDHbVJRSHKU&feature=youtu.be


Regards Itsu

magpwr

  • Hero Member
  • *****
  • Posts: 1168
    • Youtube Channel
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5468 on: October 02, 2014, 12:49:20 AM »
A little progress video below.

I finished breadboarding the TL494 with ucc37322 MOSFET drivers and IRFP260N MOSFET's.
Nice 27KHz square wave signals on the gates (drains not connected yet).

I also used one of the ucc37322 signals as input for my nano pulser with result that i now have a synced (27KHz) nano pulse (240V pp / 30ns wide).
This nano pulser now used only 40V dc as input on its MOSFET, and can take 200V input or more for a 1500V pp pulse if needed.

I also show the signal on the multi layer coil with kacher activated.
It shows that the kacher is very instable as the HV probe makes it change from 1MHz without it to 723KHz with HV probe attached.

Finally i made a remark in the video about the used primary of the yoke as seen in the latest Ruslan video.
This primary has about 2x 12 turns, so NOT the 2x 6 turns in the diagrams, see screenshot below (yellow wiring):
I started with the yoke as mentioned in the diagram, meaning 2x 6 turns primary and 28 turns / 3 turn secondaries (all CW).


Video here:  https://www.youtube.com/watch?v=hDHbVJRSHKU&feature=youtu.be


Regards Itsu

hi itsu,

Your progress amaze me as i am only at waiting for component stage eg:2C5200 x5 to be tested with existing tesla coil of different spec to see how it function especially at higher dc voltage around 100...150volts.

The diagram 12-12 turns primary for yoke would is meant for 24volts input.6-0-6 turns meant for 12volts as per circuit diagram.

The snubber circuit which was captured from Ruslan video seems to be very simple only consisting just 1 hv ceramics  capacitor around (2.2nf max possible value 10nf) around 1000volts rating.
The single resistor is just meant for the igbt /mosfet gates to source. 

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5469 on: October 02, 2014, 01:20:16 AM »
  Nice work so far Itsu.
  Glad that you decided to take the plunge.
  It will be interesting to see what happens when the kacher is tuned on, and then off, to see what difference it makes to the bulbs output brightness and readings.
 
  Remember that Ruslan and Akula are both joining the 12,12 turn resonator coil
(it's not really 25 turns times 2) to the bigger output coil. Then both are connected to an earth ground. This will probably further change your readings, and output.
Thanks for showing us your video.
 

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5470 on: October 02, 2014, 08:38:50 AM »
Hoppy, and all:  Kapanadze told me that the earth wire can be replaced by a circuit.
When I pressed him further he said it could be replaced by the negative terminal of a car battery.
This is pure Tesla tech. I have read that Tesla used the same technique.
Tesla has stated that in some of his devices you could replace an earth ground with the negative
terminal of a lead acid accumulator (car battery).
I pressed both Mike and his interpreter (who were both present during the aquarium 2 demo)
and both confirmed that the earth wire was disconnected for a few minutes.
I talked to both of them independently and some days apart.
My conclusion is that the earth "ground" is required to keep the device in phase.
I have seen experiments on youtube where the disconnect of an earth wire caused experiments to lose power,
although I don't have these video urls now.
Kapanadze uses high frequency mixing in his device. This is proved by the "dancing meters" witnessed by independent testers of some of his devices.
The only other patent I have found which uses the same technique is by Carlos Benitez.
In one of  his patents he says that an "oscillatory circuit" is required to be mixed with DC to produce OU.
An oscillatory circuit is 19th century speak for "tank circuit".
Akula use the same principle.

Hi a.king21,

Thanks for chipping in on this earthing issue. I'm now of the firm opinion, having studied Akula's various videos, that a ground connection is not essential to operation in respect of being the 'feed' for the primary source of energy to the device. I'm also reasonably sure that TK does not use any sophisticated electronics in the form of nano or PWM circuitry.

Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5471 on: October 02, 2014, 08:53:37 AM »
The following equation is for accuracy maniacs like void and me! It is tested of course.

By giving the meters of the cable that you decide to use and the outer diameter of the wire including  insulation, you can calculate the exact diameter of the PVC pipe that you need for a 48-48 24-24 12-12 output coil.

R=(L-(1733.28 X D))/1055.04

R, the radius of the PVC pipe or any other material in mm
L, the length of the wire in mm
D, the outer diameter of the cable including insulation in mm

Example.

Length of the wire L=33.75m / 33750mm
Outer diameter of the cable D=3.4mm

Rpvc= 26.4mm So diameter is 2X26.4mm= 52.8mm or 5.28cm

In my case I used 35cm connection cables for each coil ends so in equation for a wavelength of 33.75m I put as L=33.05 m

Itsu, your wire length is 32,095 meters

Keep in mind that when you put in place the 2X25Turns coil, inductance of output coil is changing and high frequency resonance fall down to a lower harmonic. Just measure bifi's resonance frequency when in place so to find the frequency of tesla.

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5472 on: October 02, 2014, 08:55:34 AM »

The snubber circuit which was captured from Ruslan video seems to be very simple only consisting just 1 hv ceramics  capacitor around (2.2nf max possible value 10nf) around 1000volts rating.
The single resistor is just meant for the igbt /mosfet gates to source.

A 10nF cap (600 - 1000V rating) with 100K across it should be fine for the snubber.


itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5473 on: October 02, 2014, 09:38:16 AM »
Thanks guys for your comments.


@ magpwr, i did not know there was a 24V version too,  ok i will start with the 2x6 primary (12V version).


@ Nick, not sure what you mean by:
 
Quote
Remember that Ruslan and Akula are both joining the 12,12 turn resonator coil
(it's not really 25 turns times 2) to the bigger output coil.

Are you saying that the L3 coil (on top of the exposed 2x48 turns part of the big main coil) is NOT 2x25 turns?
Mind you that it DOES resonates at 27KHz with a 0.47uF capacitor attached, i don't think that 2x12 will do that.


@ Jeg, thanks for the main coil wire length (32 meters), not sure why its important as any wavelength/resonance
calculations are skewed in a coil compared to the full length wire.

 
@ Hoppy,  good to know the snubber details, thanks.


Regards Itsu

zcsaba77

  • Full Member
  • ***
  • Posts: 245
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5474 on: October 02, 2014, 10:38:21 AM »
In my schematic layer not cansels each other. You not properly read schematic. You can read about dots in woundings and that they mean and if you understand how they say in that side need wound, then you understand, that in my schematic dots is properly puted.

Hi MenoF

Can you explain how mean the dots in coil windings?

Regards zcsaba77