Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11719109 times)

Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5445 on: October 01, 2014, 04:52:08 PM »
Hummm, I'm not at all convinced on the telluric currents hypothesis for the Kapa devices. You will recall that a.king21 was adamant that his 'team' witnessed disconnection of the earth wire and Kapaanadze's Aqua2 device continued to operate. The crude termination of the earth wire to Rusian's domestic radiator also is far from convincing me that ground currents are instrumental in the operation of these devices.

It is a question how that happened. But I am sticked with the elastic medium Tesla's proposal which say that em waves up to some 20-70khz are trapped inside the earth until someone to tap on them.

Void

  • Hero Member
  • *****
  • Posts: 2333
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5446 on: October 01, 2014, 05:56:16 PM »
The L1 (2x 48, 2x 24, 2x 12 turns) bifi coil self resonates at 1950KHz (with only the scope probe capacitance), but it has more (lower amplitude) resonant points higher up.

Hi Itsu. I am not sure if you mentioned it already or not, but did you measure the
inductance of your multi-layer bifilar coil? if so, what is the measured inductance?
Did you wind the 2x24 and 2x12 turns layers in the opposite direction to the 2x48 layer?
By any chance did you measure the full length of the wire you used to wind this coil, or
did you just wind it and not measure the full length of the wire?
I am going to wind my bifilar soon, so just wondering how you have done yours.
By the way, your coil assembly is a work or art. Very nice assembly job! :)
All the best.

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5447 on: October 01, 2014, 05:56:34 PM »
  The first Akula device (750w) did not need to use an earth ground connection, but he said that it ran cooler (possibly) and with higher output when using his earth ground connection.
  Which should also prove to some degree that the energy is NOT coming from the ground. As there are at least two self running devices that ran without an earth ground. But, not as well, possibly.

  So, the Ruslan hand drawn diagram (also Brutto's) does not have a nano pulser modulator crt for the Kacher oscillator???  Much simpler...?

  The 48,48  24,24 12,12 that is being mentioned is not bifilar wound. The 25 turns times 2 coil is the bifilar. But neither Akula nor Ruslan are using 2 times 25 turns, as it looks like they are using only 12,12 turns.
  Both the bifilar and the bigger air core are connected together in both Akula's diagram, as well as Ruslan's diagram. So, there are three different frequencies including the Kacher, heterodyned together to produce the results, all connected to a long earth ground cable.

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5448 on: October 01, 2014, 06:28:00 PM »


  So, this last Ruslan drawn diagram (also Brutto's) does not have a nano pulser modulator crt for the Kacher oscillator?  Much simpler...

Interestingly, it also lacks a Kacher oscillator or spark gap!  ???   So, what is Brutto trying to put over with this schematic?? Possibly that it can be made so simple that you'll laugh  ;D , or maybe its just intended as a diversion.  :-\

GeoFusion

  • Sr. Member
  • ****
  • Posts: 449
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5449 on: October 01, 2014, 06:30:23 PM »
Hi

@Mag
Thank you for posting the Tesla interview and thoughts.
I have somehow read that somewhere last year.

great to see this happing.
On the right path within this forum.


Check this out:

Akula's TT load test and frequency of arc. good material too see.

https://www.youtube.com/watch?v=1Rr-qTvTrdU

https://www.youtube.com/watch?v=uG705Ayant8#t=121




Void

  • Hero Member
  • *****
  • Posts: 2333
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5450 on: October 01, 2014, 06:37:55 PM »
Interestingly, it also lacks a Kacher oscillator or spark gap!  ???   So, what is Brutto trying to put over with this schematic?? Possibly that it can be made so simple that you'll laugh  ;D , or maybe its just intended as a diversion.  :-\

Ha ha, easy mate. :) Brutto just redrew Ruslan's hand drawn schematic from Ruslan's video.
Probably for simplicity, the component details on the push pull driver and kacher driver circuits were not included
in Ruslan's drawing, but instead were just shown as blocks. It doesn't mean that those driver circuits are not there. :)
We just don't know all the exact components that Ruslan used since he showed only blocks for those two devices.
It could be Ruslan didn't want to show exact details there, or maybe he felt those circuits are widely known
now, so to save time he just drew blocks for the driver circuits.
All the best...


NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5451 on: October 01, 2014, 06:42:42 PM »
  Hoppy:
  It looks like that are some unnecessary things in the older versions, which are being discarded as they are possibly not needed anymore.
   
  Also, check my edit to my last previous post.

  Geo: I built a new Mazilli crt to use, instead of the fet protection crt used by Ruslan. This is because I don't see much difference in that part of the induction crt. And since I don't have the nano pulser thingy, I still need to turn the induction crt part using the tuning caps. Or the amplitude is not a good as I had it working previously with my original Mazilli tuned using the capacitors.
Possibly these tuning caps are doing what the frequency adjustment pots are doing in the nano pulser. I tune to maximum output by using these caps.
What do you think?

  Void:  Ruslan has a new circuit, and did not show it in the "blocks".
But, may include it later on in his diagram, when he get the new set up tested and working properly.
  My question is, if this new circuit includes a separate modulator to control the Kacher's duty cycle, and frequency controller. Or not?

d3x0r

  • Hero Member
  • *****
  • Posts: 1433
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5452 on: October 01, 2014, 06:43:58 PM »
re 7414/7400


The high/low on of that system can be reversed by reversing the connection on the 40/.5 transformer
it's overall an enabled system, that even the chips aren't powered on a low state.
that provides the pull-up basis for the kacher... otherwise it's low-normal, and not conducting.


 it looks like the drive kacher would be pulled high during a high on the output. 
It operates on one half or the other of the low frequency drive... but again just reverse the connection to the 40 turn coil and it's the other side.


re: removable coil -
think that's the whole coil assembly... the one in this schematic that doesn't have specific turns labeled...
I sometimes think he refers to a specific coil on that... like the extra drive coil on the kapa-coil... but maybe it's the whole assembly.

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5453 on: October 01, 2014, 06:56:14 PM »
Ha ha, easy mate. :) Brutto just redrew Ruslan's hand drawn schematic from Ruslan's video.
Probably for simplicity, the component details on the push pull driver and kacher driver circuits were not included
in Ruslan's drawing, but instead were just shown as blocks. It doesn't mean that those driver circuits are not there. :)
We just don't know all the exact components that Ruslan used since he showed only blocks for those two devices.
It could be Ruslan didn't want to show exact details there, or maybe he felt those circuits are widely known
now, so to save time he just drew blocks for the driver circuits.
All the best...

I am are referring to Brutto's drawing in post 5436, not his neatly drawn schematic based on Rusian's circuit diagram. The empty blocks  obviously signify other circuit elements.

Void

  • Hero Member
  • *****
  • Posts: 2333
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5454 on: October 01, 2014, 07:00:22 PM »
I am are referring to Brutto's drawing in post 5436, not his neatly drawn schematic based on Rusian's circuit diagram. The empty blocks  obviously signify other circuit elements.

That's a simplified drawing to show an overview of component connections.
It likely was meant to show all components.  :)
All the best.

Void

  • Hero Member
  • *****
  • Posts: 2333
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5455 on: October 01, 2014, 07:02:49 PM »
re: removable coil -
think that's the whole coil assembly... the one in this schematic that doesn't have specific turns labeled...
I sometimes think he refers to a specific coil on that... like the extra drive coil on the kapa-coil... but maybe it's the whole assembly.

Hi d3x0r. Thanks for the comments on that. It is confusing why he is using the
term 'removable coil', but maybe it has a different meaning altogether in Russian
than it comes out in the English translation. ;)
All the best...

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5456 on: October 01, 2014, 07:04:49 PM »
That's a simplified drawing to show an overview of component connections.
It likely was meant to show all components.  :)
All the best.

Maybe  ;) Perhaps he ran out of pencil lead.  ;D

Void

  • Hero Member
  • *****
  • Posts: 2333
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5457 on: October 01, 2014, 07:04:57 PM »
   The 48,48  24,24 12,12 that is being mentioned is not bifilar wound.

Hi Nick. Each layer of two windings of the same count can be viewed as a bifilar winding.
All the best...

starcruiser

  • Hero Member
  • *****
  • Posts: 693
    • Starcruiser's Place
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5458 on: October 01, 2014, 07:35:18 PM »
Thanks starcruiser, but why is that important? What is it with this 1.8MHz operating frequency?  (66.6 times 27KHz?).

Thanks,  itsu

@itsu, I think it is more important to match a harmonic of the fundamental frequency you are trying to hit. The coils should be sized, IMPO, to a wavelength that is a harmonic as I mentioned prior. The pull down you mention could be a 1/4 wave, i.e. a 4th harmonic.

I really do think the coils need to be matched in order to function effectively. This is truly the case with radio tuning sections.

starcruiser

  • Hero Member
  • *****
  • Posts: 693
    • Starcruiser's Place
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5459 on: October 01, 2014, 07:38:07 PM »
Hi Nick. Each layer of two windings of the same count can be viewed as a bifilar winding.
All the best...


I see the coil is wound to reduce self inductance, the base layer is LH wind, then back as a RH wind then the next shorter one is opposite, RH wind then LH, the smallest seems to follow the middle wind direction... a picture was posted of one of the TK coils which shows this (in this thread recently). Posted by Geo

http://www.overunity.com/12736/kapanadze-cousin-dally-free-energy/msg418454/#msg418454