For T-1000 or any other russian... can you explain the following translation?

Of the gene on human trafficking....


Of the gene on human trafficking to the coil which voltage-150V? And gene-150 postoyanke?


От ген на ТЛ на катушку какое напряжение-150в?И на ген-150 постоянка?


Reh(ген) is short for General?  it's Gen?  is that Generator?  I see the short ген a lot.
human trafficing I guess is 'slaves to'?

Aidas, now you are Russian , congratulations on the promotion.
Ignore the trolls (Ganzha) and work quietly. Good luck!

to d3x0r. GEN - is Russian slang Electrotechnical is short for - generator. GEN - Generator ( ГЕН - генератор)
to the generals no relation.
постоянка - it's direct current
"От ген на ТЛ на катушку какое напряжение-150в?И на ген-150 постоянка?" - it's = "from a generator on ТЛ (TL494) on the coil how much voltage - 150 volts? and on genernator - 150 volts DC?"

Regards to all
Vasiliy

With regards to the nano pulser element of the circuit, is there something special about the KD203 diode (700V / 10A), which precludes substitution? It looks like a standard type of rectifier to me, please correct me if I'm wrong.
With a good spec for the green transformer, between us, we should be able to replicate accurately.

Regards
Hoppy

Yes, this is a standard rectifier diode, the old type.
KД203, KД204, and many others can be used, it is necessary to try.

Regards

What actually happens when you can douple the amplitude of a wave via superimposition of a reflected wave ?
Is the power not 4 times the initial wave ?


You send two waves into it and the output is double these two waves...


I know that Jdo300 tried to replicate exactly this in the times of steven marks tpu replication going on...
see here: [size=78%]http://www.youtube.com/watch?v=OqwPMAJsh3I[/size]

I did some measuring of my coils...
L1 is 2.28uH  28gauge
L2 is 1.265uH  24 gauge
l3 (insdie and outside) is 0.026uh (lowest end of my meter, not nesscarily accurate)
l4 is .126uh  12 gauge
the additional coil I had on L4 is .256uh



My L2 computes resonant around 4.3Khz with 1uf cap (almost exactly 1.0)


L2 was pk-pk 200V, the L1 driver voltage is something around 150V, as my neons only come on briefly, so, by turns, the best I could do ....


L1 is 22.5cm long, and using 28 gauge wire has 25 turns/cm for 562 turns.
L2 is 22.5cm long and using is approx 20 turns/cm for 450turns
L4 is wound with 12 gauge wire, 4 turns/cm, and is 24cm long, 96 turns.


L1 : 562:96 = 5.854 .... 150V/5.854 = 25V
L2 : 450:96 = 4.687 ... 100V/4.687 = 21V  (100V for half wave rectified...)


but I was clearly reading 75V on the capacitor across L4 (when L2 was at resonance)


The cap I was using on the L2 coil was also a 100V mylar capacitor, maybe that capped it?  But it didn't look chopped or have strange drops...

Don't you mean 2.28mH for L1?

Dally has only 159 turns for L2. You have almost three times more turns and almost 100 more turns on L1, so your voltage levels will be higher than from a Dally spec coil.

Regards
Hoppy

An interesting finding was that when I changed the nano VCO and nano pulser chips from SN7400's to 74HCT00's as per spec, the VCO immediately went into uncontrolled 'clean' sine wave oscillation at around 75MHz! I've heard about this problem in other applications with the HCT type chip. The SN7400's work fine. Its not a problem with the supply line as I still get the problem when powered on its own direct from my bench supply. Something to be aware of and I wonder if Dally had checked his VCO output on a scope.

Regards
Hoppy

Some GOOD NEWS !!


Dally have made another Solid-State-OU-Generator. He still waiting Chinese oscillograph. It's seems to me that Chinesse don't like to sell digital oscillographes  to Russian people.
The same as Americans. Interestingly almost all High-Tech Digital Oscillographs which are on auctions on Ebay don't sell to Russian people. If you don't belive me check youself. NO DELIVERY OF SUCH EQUIPMENT TO RUSSIA. Coonclusions make yourself !! I will not use "SHARP WORDS" for now !!

Second GOOD NEWS is this. Finally WE know The Secret of Stanley Meyer's water fuel cell. Now it's time to be revealed. The Secret is Nano-Pulser. Yes, he had used High-Energy sharp nano-pulses to separate water on Hydrogen and Oxigen in his water fuel cell. Unfortunately for him and all humankind American secret services had killed him and stop his genious production of Hydrogen and Oxigen to be spreaded over the world. Calculate how many toxic gases went to our atmosphere for last more than 20 years. Then calculat how many human lifes were lost in OIL BARONS WARS for oil production and how many people were died for presence of hard metals in their vital organs??

So my suggestion to members od this forum is very simple and reasonable. When next time some trolls wherever from which country they are, talk rubish, ask them about above present facts and shout-up their vile mouths for all times.

Look at last picture and tell me what did you seeing. In fact not me by tell the others to see and wake-up !! Maybe next chance will not be !! The Destiny is in hands all of us. Think about !!

http://www.liveinternet.ru/users/edward_lee

Very good info on the Russian parts!  Thank you.

For ГУН (VCO) use 74AC00PC and for ГНСИ (Nano-Pulser) КР1533ЛА3.

Does the КР1533ЛА3 Quad NAND Gate  belong to the 74ALS... family?
Why is it necessary to mix different logic families? AC and ALS ?

To make several kV Nano-Pulser pulses use several diodes serially. Ferrite ring i think you can find easy. You may use bigger ring up to 2 cm outer diameter.  Ðœ6000НМ or better.
Ferrite is going hot so must be sealed or glued on KT926 radiator. And connecting wires must be as short as possible if you want nano pulses !! For Ferrite ring use quality teflon wire or wire which isolation can handle more than 200 degrees temperaure. This is important coz Ferrite ring, Transistor and DSRD will running continuously. Use good radiator for DSRD diode!!

What do you think of the transformerless method of driving the DSR diode, like shown on the diagram below? I can get 800ps 320V pulse with 12VDC power supply.

Привет всем !!


I found our Russian parts on Ebay.com


RUSSIAN DSRD diode KD206A
http://www.ebay.com/itm/KD206A-USSR-RUSSIAN-RECTIFIER-DIODES-LOT-OF-50-NEW-/220683918392?pt=LH_DefaultDomain_0&hash=item3361c95c38

$38.50/50=0.77$ per part

RUSSIAN DSRD diode KD226G Rectifier Diode 600V 1.7A NOS
http://www.ebay.com/itm/100-PCS-KD226G-Rectifier-Diode-600V-1-7A-NOS-/251057009269?pt=LH_DefaultDomain_0&hash=item3a7429f275

US $5.50

MILITARY GRADE RUSSIAN AVALANCHE Rectifier DIODE DL171-320-14 320A 1400V 1,4kV
http://www.ebay.com/itm/MILITARY-GRADE-Soviet-AVALANCHE-Rectifier-DIODE-DL171-320-14-320A-1400V-1-4kV-/250979935248?pt=LH_DefaultDomain_0&hash=item3a6f91e410

US $59.99

RUSSIAN-MILITARY-KT926B-KT926-SILICON-PNP-TRANSISTOR
http://www.ebay.com/itm/RUSSIAN-MILITARY-KT926B-KT926-SILICON-PNP-TRANSISTOR-7pcs-all-1991y-/350603040082?pt=LH_DefaultDomain_0&hash=item51a191d552
RUSSIAN MILITARY KT926B

US $17.00

RUSSIAN-KR1533LA3 = 74ALS00 ( 74 ALS 00 )
http://www.ebay.com/itm/New-3-pcs-x-KR1533LA3-74ALS00-74-ALS-00-1533-3-/190598741118?_trksid=p2045573.m2042&_trkparms=aid%3D111000%26algo%3DREC.CURRENT%26ao%3D1%26asc%3D27%26meid%3D2475968235941317723%26pid%3D100033%26prg%3D1011%26rk%3D1%26sd%3D190598741118%26

US $1.89

For ГУН (VCO) use 74AC00PC and for ГНСИ (Nano-Pulser) КР1533ЛА3.

To make several kV Nano-Pulser pulses use several diodes serially. Ferrite ring i think you can find easy. You may use bigger ring up to 2 cm outer diameter.  Ðœ6000НМ or better.
Ferrite is going hot so must be sealed or glued on KT926 radiator. And connecting wires must be as short as possible if you want nano pulses !! For Ferrite ring use quality teflon wire or wire which isolation can handle more than 200 degrees temperaure. This is important coz Ferrite ring, Transistor and DSRD will running continuously. Use good radiator for DSRD diode!!

Thanks for the info. A couple of points: The KT926 transistor is shown incorrectly as PNP. It is as far as I can tell from spec, an NPN. Where did you find out that the KD226G is DSRD?

Regards
Hoppy